Router and Routing Basics Final Exam

Frage 1 von 80

1

Refer to the exhibit. What will be the effect of entering the command that is shown in the exhibit on R2 as part of the dynamic NAT configuration?

Wähle eine der folgenden:

It will define a pool of addresses for translation.
It will identify an inside NAT interface.
It will bind NAT-POOL1 with ACL 1.
It will define the source ACL for the external interface.

Erklärung

Frage 2 von 80

1

A network engineer has configured a router with the command ip nat inside source list 4 pool corp overload. Why did the engineer use the overload option?

Wähle eine der folgenden:

The company has more private IP addresses than available public IP addresses.
The company needs to have more public IP addresses available to be used on the Internet.
The company router must throttle or buffer traffic because the processing power of the router is not enough to handle the normal load of external-bound Internet traffic.
The company has a small number of servers that should be accessible by clients from the Internet.

Erklärung

Frage 3 von 80

1

What is the purpose of port forwarding?

Wähle eine der folgenden:

Port forwarding allows an external user to reach a service on a private IPv4 address that is located inside a LAN.
Port forwarding allows users to reach servers on the Internet that are not using standard port numbers.
Port forwarding allows an internal user to reach a service on a public IPv4 address that is located outside a LAN.
Port forwarding allows for translating inside local IP addresses to outside local addresses.

Erklärung

Frage 4 von 80

1

Refer to the exhibit. Based on the output that is shown, what type of NAT has been implemented?

Wähle eine der folgenden:

dynamic NAT with a pool of two public IP addresses
PAT using an external interface
static NAT with one entry
static NAT with a NAT pool

Erklärung

Frage 5 von 80

1

Using NAT terminology, what is the address of the source host on a private network as seen from inside the network?

Wähle eine der folgenden:

inside local
inside global
outside global
outside local

Erklärung

Frage 6 von 80

1

What is an advantage of deploying IPv4 NAT technology for internal hosts in an organization?

Wähle eine der folgenden:

makes internal network access easy for outside hosts using UDP
provides flexibility in designing the IPv4 addressing scheme
increases the performance of packet transmission to the Internet
enables the easy deployment of applications that require end-to-end traceability

Erklärung

Frage 7 von 80

1

What are two of the required steps to configure PAT? (Choose two.)

Wähle eine oder mehr der folgenden:

Define a pool of global addresses to be used for overload translation.
Create a standard access list to define applications that should be translated.
Define the range of source ports to be used.
Identify the inside interface
Define the hello and interval timers to match the adjacent neighbor router.

Erklärung

Frage 8 von 80

1

Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server?

Wähle eine der folgenden:

unicast DHCPACK
broadcast DHCPACK
unicast DHCPREQUEST
broadcast DHCPREQUEST

Erklärung

Frage 9 von 80

1

Which set of commands will configure a router as a DHCP server that will assign IPv4 addresses to the 192.168.100.0/23 LAN while reserving the first 10 and the last addresses for static assignment?

Wähle eine der folgenden:

ip dhcp excluded-address 192.168.100.1 192.168.100.10
ip dhcp excluded-address 192.168.100.254
ip dhcp pool LAN-POOL-100
network 192.168.100.0 255.255.255.0
ip default-gateway 192.168.100.1
ip dhcp excluded-address 192.168.100.1 192.168.100.10
ip dhcp excluded-address 192.168.101.254
ip dhcp pool LAN-POOL-100
network 192.168.100.0 255.255.254.0
default-router 192.168.100.1
dhcp pool LAN-POOL-100
ip dhcp excluded-address 192.168.100.1 192.168.100.9
ip dhcp excluded-address 192.168.100.254
network 192.168.100.0 255.255.254.0
default-router 192.168.101.1
ip dhcp excluded-address 192.168.100.1 192.168.100.9
ip dhcp excluded-address 192.168.101.254
ip dhcp pool LAN-POOL-100
ip network 192.168.100.0 255.255.254.0
ip default-gateway 192.168.100.1

Erklärung

Frage 10 von 80

1

Under which two circumstances would a router usually be configured as a DHCPv4 client? (Choose two.)

Wähle eine oder mehr der folgenden:

The router is intended to be used as a SOHO gateway
The administrator needs the router to act as a relay agent.
The router is meant to provide IP addresses to the hosts.
This is an ISP requirement.
The router has a fixed IP address

Erklärung

Frage 11 von 80

1

A network administrator configures a router to send RA messages with M flag as 0 and O flag as 1. Which statement describes the effect of this configuration when a PC tries to configure its IPv6 address?

Wähle eine der folgenden:

It should contact a DHCPv6 server for all the information that it needs.
It should use the information that is contained in the RA message exclusively.
It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.
It should contact a DHCPv6 server for the prefix, the prefix-length information, and an interface ID that is both random and unique.

Erklärung

Frage 12 von 80

1

An administrator wants to configure hosts to automatically assign IPv6 addresses to themselves by the use of Router Advertisement messages, but also to obtain the DNS server address from a DHCPv6 server. Which address assignment method should be configured?

Wähle eine der folgenden:

SLAAC
stateless DHCPv6
stateful DHCPv6
RA and EUI-64

Erklärung

Frage 13 von 80

1

Refer to the exhibit. Based on the output that is shown, what kind of IPv6 addressing is being configured?

Wähle eine der folgenden:

SLAAC
stateful DHCPv6
stateless DHCPv6
static link-local

Erklärung

Frage 14 von 80

1

Which two characteristics are shared by both standard and extended ACLs? (Choose two.)

Wähle eine oder mehr der folgenden:

Both kinds of ACLs can filter based on protocol type.
Both can permit or deny specific services by port number.
Both include an implicit deny as a final entry.
Both filter packets for a specific destination host IP address.
Both can be created by using either a descriptive name or number.

Erklärung

Frage 15 von 80

1

A network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.)

Wähle eine oder mehr der folgenden:

Router1(config)# access-list 10 permit host 192.168.15.23
Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.0
Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.255
Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.0
Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.255

Erklärung

Frage 16 von 80

1

Refer to the exhibit. What will happen to the access list 10 ACEs if the router is rebooted before any other commands are implemented?

Wähle eine der folgenden:

The ACEs of access list 10 will be deleted.
The ACEs of access list 10 will not be affected.
The ACEs of access list 10 will be renumbered.
The ACEs of access list 10 wildcard masks will be converted to subnet masks

Erklärung

Frage 17 von 80

1

An administrator has configured an access list on R1 to allow SSH administrative access from host 172.16.1.100. Which command correctly applies the ACL?

Wähle eine der folgenden:

R1(config-if)# ip access-group 1 in
R1(config-if)# ip access-group 1 out
R1(config-line)# access-class 1 in
R1(config-line)# access-class 1 out

Erklärung

Frage 18 von 80

1

What is a limitation when utilizing both IPv4 and IPv6 ACLs on a router?

Wähle eine der folgenden:

A device can run only IPv4 ACLs or IPv6 ACLs.
Both IPv4 and IPv6 ACLs can be configured on a single device, but cannot share the same name.
IPv4 ACLs can be numbered or named whereas IPv6 ACLs must be numbered
IPv6 ACLs perform the same functions as standard IPv4 ACLs.

Erklärung

Frage 19 von 80

1

What method is used to apply an IPv6 ACL to a router interface?

Wähle eine der folgenden:

the use of the access-class command
the use of the ip access-group command
the use of the ipv6 traffic-filter command
the use of the ipv6 access-list command

Erklärung

Frage 20 von 80

1

Which three implicit access control entries are automatically added to the end of an IPv6 ACL? (Choose three.)

Wähle eine oder mehr der folgenden:

deny ip any any
deny ipv6 any any
permit ipv6 any any
deny icmp any any
permit icmp any any nd-ns
permit icmp any any nd-na

Erklärung

Frage 21 von 80

1

Which three statements describe the similarities between OSPFv2 and OSPFv3? (Choose three)

Wähle eine oder mehr der folgenden:

They both are link-state protocols.
They both use the global address as the source address when sending OSPF messages.
They both share the concept of multiple areas.
They both support IPsec for authentication.
They both use the same DR/BDR election process.
They both have unicast routing enabled by default.

Erklärung

Frage 22 von 80

1

What is a function of OSPF hello packets?

Wähle eine der folgenden:

to send specifically requested link-state records
to discover neighbors and build adjacencies between them
to ensure database synchronization between routers
to request specific link-state records from neighbor routers

Erklärung

Frage 23 von 80

1

What are the two purposes of an OSPF router ID? (Choose two.)

Wähle eine oder mehr der folgenden:

to facilitate the establishment of network convergence
to uniquely identify the router within the OSPF domain
to facilitate the transition of the OSPF neighbor state to Full
to facilitate router participation in the election of the designated router
to enable the SPF algorithm to determine the lowest cost path to remote networks

Erklärung

Frage 24 von 80

1

Which wildcard mask would be used to advertise the 192.168.5.96/27 network as part of an OSPF configuration?

Wähle eine der folgenden:

0.0.0.32
0.0.0.31
255.255.255.224
255.255.255.223

Erklärung

Frage 25 von 80

1

Which three addresses could be used as the destination address for OSPFv3 messages? (Choose three.)

Wähle eine oder mehr der folgenden:

FE80::1
FF02::5
FF02::6
FF02::A
FF02::1:2
2001:db8:cafe::1

Erklärung

Frage 26 von 80

1

What does a Cisco router use automatically to create link-local addresses on serial interfaces when OSPFv3 is implemented?

Wähle eine der folgenden:

the highest MAC address available on the router, the FE80::/10 prefix, and the EUI-48 process
the FE80::/10 prefix and the EUI-48 process
the MAC address of the serial interface, the FE80::/10 prefix, and the EUI-64 process
an Ethernet interface MAC address available on the router, the FE80::/10 prefix, and the EUI-64 process

Erklärung

Frage 27 von 80

1

A network administrator enters the command ipv6 router ospf 64 in global configuration mode. What is the result of this command?

Wähle eine der folgenden:

The router will be assigned an autonomous system number of 64.
The router will be assigned a router ID of 64
The reference bandwidth will be set to 64 Mb/s.
The OSPFv3 process will be assigned an ID of 64.

Erklärung

Frage 28 von 80

1

Which command will provide information specific to OSPFv3 routes in the routing table?

Wähle eine der folgenden:

show ip route ospf
show ip route
show ipv6 route
show ipv6 route ospf

Erklärung

Frage 29 von 80

1

What is a disadvantage of using dynamic routing protocols?

Wähle eine der folgenden:

They are only suitable for simple topologies.
Their configuration complexity increases as the size of the network grows.
They send messages about network status insecurely across networks by default.
They require administrator intervention when the pathway of traffic changes.

Erklärung

Frage 30 von 80

1

Which two statements are true regarding classless routing protocols? (Choose two.)

Wähle eine oder mehr der folgenden:

sends subnet mask information in routing updates
sends complete routing table update to all neighbors
is supported by RIP version 1
allows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
reduces the amount of address space available in an organization

Erklärung

Frage 31 von 80

1

While configuring RIPv2 on an enterprise network, an engineer enters the command network 192.168.10.0 into router configuration mode.

Wähle eine der folgenden:

The interface of the 192.168.10.0 network is sending version 1 and version 2 update
The interface of the 192.168.10.0 network is receiving version 1 and version 2 updates
The interface of the 192.168.10.0 network is sending only version 2 updates.
The interface of the 192.168.10.0 network is sending RIP hello messages.

Erklärung

Frage 32 von 80

1

Refer to the exhibit. A network administrator has issued the exhibited commands in an attempt to activate RIPng on interface gig0/0. What is causing the console message that is shown after RIP is enabled?

Wähle eine der folgenden:

Interface gig0/0 is shutdown
Interface gig0/0 does not have a valid IPv6 address.
IPv6 unicast routing has not been enabled on this router.
IPv6 is not supported on this IOS.

Erklärung

Frage 33 von 80

1

When does a link-state router send LSPs to its neighbors?

Wähle eine der folgenden:

every 30 seconds
immediately after receiving an LSP from neighbors with updates
only when one of its neighbors requests an update
only when one of its interfaces goes up or down

Erklärung

Frage 34 von 80

1

Which routing protocol uses link-state information to build a map of the topology for computing the best path to each destination network?

Wähle eine der folgenden:

OSPF
EIGRP
RIP
RIPng

Erklärung

Frage 35 von 80

1

Which type of route will require a router to perform a recursive lookup?

Wähle eine der folgenden:

an ultimate route that is using a next hop IP address on a router that is not using CEF
a level 2 child route that is using an exit interface on a router that is not using CEF
a level 1 network route that is using a next hop IP address on a router that is using CEF
a parent route on a router that is using CEF

Erklärung

Frage 36 von 80

1

A router is configured to participate in multiple routing protocol: RIP, EIGRP, and OSPF. The router must send a packet to network 192.168.14.0. Which route will be used to forward the traffic?

Wähle eine der folgenden:

a 192.168.14.0 /26 route that is learned via RIP
a 192.168.14.0 /24 route that is learned via EIGRP
a 192.168.14.0 /25 route that is learned via OSPF
a 192.168.14.0 /25 route that is learned via RIP

Erklärung

Frage 37 von 80

1

What is different between IPv6 routing table entries compared to IPv4 routing table entries?

Wähle eine der folgenden:

IPv6 routing tables include local route entries which IPv4 routing tables do not
By design IPv6 is classless so all routes are effectively level 1 ultimate routes
The selection of IPv6 routes is based on the shortest matching prefix, unlike IPv4 route selection which is based on the longest matching prefix.
IPv6 does not use static routes to populate the routing table as used in IPv4.

Erklärung

Frage 38 von 80

1

Refer to the exhibit. The network engineer for the company that is shown wants to use the primary ISP connection for all external connectivity. The backup ISP connection is used only if the primary ISP connection fails. Which set of commands would accomplish this goal?

Wähle eine der folgenden:

ip route 198.133.219.24 255.255.255.252
ip route 64.100.210.80 255.255.255.252
ip route 198.133.219.24 255.255.255.252
ip route 64.100.210.80 255.255.255.252 10
ip route 0.0.0.0 0.0.0.0 s0/0/0
ip route 0.0.0.0 0.0.0.0 s0/1/0
ip route 0.0.0.0 0.0.0.0 s0/0/0
ip route 0.0.0.0 0.0.0.0 s0/1/0 10

Erklärung

Frage 39 von 80

1

What are two advantages of static routing over dynamic routing? (Choose two.)

Wähle eine oder mehr der folgenden:

Static routing is more secure because it does not advertise over the network.
Static routing scales well with expanding networks.
Static routing requires very little knowledge of the network for correct implementation
Static routing uses fewer router resources than dynamic routing
Static routing is relatively easy to configure for large networks

Erklärung

Frage 40 von 80

1

What is the correct syntax of a floating static route?

Wähle eine der folgenden:

ip route 209.165.200.228 255.255.255.248 serial 0/0/0
ip route 209.165.200.228 255.255.255.248 10.0.0.1 120
ip route 0.0.0.0 0.0.0.0 serial 0/0/0
ip route 172.16.0.0 255.248.0.0 10.0.0.1

Erklärung

Frage 41 von 80

1

Which type of static route that is configured on a router uses only the exit interface?

Wähle eine der folgenden:

recursive static route
directly connected static route
fully specified static route
default static route

Erklärung

Frage 42 von 80

1

Refer to the exhibit. The network administrator needs to configure a default route on the Border router. Which command would the administrator use to configure a default route that will require the least amount of router processing when forwarding packets?

Wähle eine der folgenden:

Border(config)# ip route 0.0.0.0 0.0.0.0 198.133.219.5
Border(config)# ip route 0.0.0.0 0.0.0.0 198.133.219.6
Border(config)# ip route 0.0.0.0 0.0.0.0 s0/0/1
Border(config)# ip route 0.0.0.0 0.0.0.0 s0/0/0

Erklärung

Frage 43 von 80

1

What two pieces of information are needed in a fully specified static route to eliminate recursive lookups? (Choose two.)

Wähle eine oder mehr der folgenden:

the interface ID exit interface
the interface ID of the next-hop neighbor
the IP address of the next-hop neighbor
the administrative distance for the destination network
the IP address of the exit interface

Erklärung

Frage 44 von 80

1

What does VLSM allow a network administrator to do?

Wähle eine der folgenden:

utilize one subnet mask throughout a hierarchical network
utilize multiple routing protocols within an autonomous system
utilize one dynamic routing protocol throughout the entire network
utilize multiple different subnet masks in the same IP address space
utilize one public IP address to translate multiple private addresses

Erklärung

Frage 45 von 80

1

What is a valid summary route for IPv6 networks 2001:0DB8:ACAD:4::/64, 2001:0DB8:ACAD:5::/64, 2001:0DB8:ACAD:6::/64, and 2001:0DB8:ACAD:7::/64?

Wähle eine der folgenden:

2001:0DB8:ACAD:0000::/63
2001:0DB8:ACAD:0000::/64
2001:0DB8:ACAD:0004::/62
2001:0DB8:ACAD:0004::/63

Erklärung

Frage 46 von 80

1

Consider the following command:
ip route 192.168.10.0 255.255.255.0 10.10.10.2 5
How would an administrator test this configuration?

Wähle eine der folgenden:

Delete the default gateway route on the router
Ping any valid address on the 192.168.10.0/24 network
Manually shut down the router interface used as a primary route
Ping from the 192.168.10.0 network to the 10.10.10.2 address

Erklärung

Frage 47 von 80

1

Refer to the exhibit. The small company shown uses static routing. Users on the R2 LAN have reported a problem with connectivity. What is the issue?

Wähle eine der folgenden:

R2 needs a static route to the R1 LANs
R1 and R2 must use a dynamic routing protocol
R1 needs a default route to R2
R1 needs a static route to the R2 LAN.
R2 needs a static route to the Internet

Erklärung

Frage 48 von 80

1

What happens to a static route entry in a routing table when the outgoing interface associated with that route goes into the down state?

Wähle eine der folgenden:

The static route is removed from the routing table.
The router polls neighbors for a replacement route
The static route remains in the table because it was defined as static
The router automatically redirects the static route to use another interface

Erklärung

Frage 49 von 80

1

What is a disadvantage of using router-on-a-stick inter-VLAN routing?

Wähle eine der folgenden:

does not support VLAN-tagged packets
requires the use of more physical interfaces than legacy inter-VLAN routing
does not scale well beyond 50 VLANs
requires the use of multiple router interfaces configured to operate as access links

Erklärung

Frage 50 von 80

1

How is traffic routed between multiple VLANs on a multilayer switch?

Wähle eine der folgenden:

Traffic is routed via physical interfaces
Traffic is routed via internal VLAN interfaces
Traffic is broadcast out all physical interfaces
Traffic is routed via subinterfaces

Erklärung

Frage 51 von 80

1

Refer to the exhibit. In what switch mode should port G0/1 be assigned if Cisco best practices are being used?

Wähle eine der folgenden:

access
trunk
native
auto

Erklärung

Frage 52 von 80

1

Refer to the exhibit. Communication between the VLANs is not occurring. What could be the issue?

Wähle eine der folgenden:

The wrong port on the router has been used.
The Gi1/1 switch port is not in trunking mode
A duplex issue exists between the switch and the router
Default gateways have not been configured for each VLAN

Erklärung

Frage 53 von 80

1

Inter-VLAN communication is not occurring in a particular building of a school. Which two commands could the network administrator use to verify that inter-VLAN communication was working properly between a router and a Layer 2 switch when the router-on-a-stick design method is implemented? (Choose two.)

Wähle eine oder mehr der folgenden:

From the router, issue the show ip route command.
From the router, issue the show interfaces trunk command
From the router, issue the show interfaces interface command
From the switch, issue the show interfaces trunk command.
From the switch, issue the show interfaces interface command

Erklärung

Frage 54 von 80

1

What is a characteristic of a routed port on a Layer 3 switch?

Wähle eine der folgenden:

It supports trunking.
It is not assigned to a VLAN
It is commonly used as a WAN link
It cannot have an IP address assigned to it.

Erklärung

Frage 55 von 80

1

Which statement describes a disadvantage of using router subinterfaces for inter-VLAN routing?

Wähle eine der folgenden:

It is more expensive than using individual router interfaces.
Routed traffic must contend for bandwidth on a single router interface.
Trunking cannot be used to connect the router to the switch
All untagged traffic is dropped

Erklärung

Frage 56 von 80

1

Refer to the exhibit. After attempting to enter the configuration that is shown in router RTA, an administrator receives an error and users on VLAN 20 report that they are unable to reach users on VLAN 30. What is causing the problem?

Wähle eine der folgenden:

Dot1q does not support subinterfaces
There is no address on Fa0/0 to use as a default gateway
RTA is using the same subnet for VLAN 20 and VLAN 30
The no shutdown command should have been issued on Fa0/0.20 and Fa0/0.30

Erklärung

Frage 57 von 80

1

What condition is required to enable Layer 3 switching?

Wähle eine der folgenden:

The Layer 3 switch must have IP routing enabled
All participating switches must have unique VLAN numbers
All routed subnets must be on the same VLAN
Inter-VLAN portions of Layer 3 switching must use router-on-a-stick.

Erklärung

Frage 58 von 80

1

Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)

Wähle eine oder mehr der folgenden:

Administrative distance refers to the trustworthiness of a particular route
A router first installs routes with higher administrative distances.
The value of the administrative distance can not be altered by the network administrator
Routes with the smallest metric to a destination indicate the best path
The metric is always determined based on hop count.
The metric varies depending which Layer 3 protocol is being routed, such as IP.

Erklärung

Frage 59 von 80

1

Which software is used for a network administrator to make the initial router configuration securely?

Wähle eine der folgenden:

SSH client software
Telnet client software
HTTPS client software
terminal emulation client software

Erklärung

Frage 60 von 80

1

Refer to the exhibit. PC A sends a request to Server B. What IPv4 address is used in the destination field in the packet as the packet leaves PC A?

Wähle eine der folgenden:

192.168.10.10
192.168.11.1
192.168.101.1
192.168.12.16

Erklärung

Frage 61 von 80

1

What is a characteristic of an IPv4 loopback interface on a Cisco IOS router?

Wähle eine der folgenden:

The no shutdown command is required to place this interface in an UP state
It is a logical interface internal to the router
Only one loopback interface can be enabled on a router
It is assigned to a physical port and can be connected to other devices

Erklärung

Frage 62 von 80

1

Which two items are used by a host device when performing an ANDing operation to determine if a destination address is on the same local network? (Choose two.)

Wähle eine oder mehr der folgenden:

destination IP address
destination MAC address
source MAC address
subnet mask
network number

Erklärung

Frage 63 von 80

1

Which two parameters are used by EIGRP as metrics to select the best path to reach a network? (Choose two.)

Wähle eine oder mehr der folgenden:

hop count
bandwidth
jitter
resiliency
delay
confidentiality

Erklärung

Frage 64 von 80

1

Consider the following routing table entry for R1:
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
What is the significance of the Serial0/0/0?

Wähle eine der folgenden:

It is the interface on R1 used to send data that is destined for 10.1.1.0/24
It is the R1 interface through which the EIGRP update was learned
It is the interface on the final destination router that is directly connected to the 10.1.1.0/24 network.
It is the interface on the next-hop router when the destination IP address is on the 10.1.1.0/24 network

Erklärung

Frage 65 von 80

1

A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226. What is the purpose of this command?

Wähle eine der folgenden:

to forward all packets to the device with IP address 209.165.200.226
to add a dynamic route for the destination network 0.0.0.0 to the routing table
to forward packets destined for the network 0.0.0.0 to the device with IP address 209.165.200.226
to provide a route to forward packets for which there is no route in the routing table

Erklärung

Frage 66 von 80

1

What command will enable a router to begin sending messages that allow it to configure a link-local address without using an IPv6 DHCP server?

Wähle eine der folgenden:

the ipv6 route ::/0 command
a static route
the ip routing command
the ipv6 unicast-routing command

Erklärung

Frage 67 von 80

1

Which statement describes a route that has been learned dynamically?

Wähle eine der folgenden:

It is automatically updated and maintained by routing protocols
It is unaffected by changes in the topology of the network.
It has an administrative distance of 1.
It is identified by the prefix C in the routing table

Erklärung

Frage 68 von 80

1

Which type of VLAN is used to designate which traffic is untagged when crossing a trunk port?

Wähle eine der folgenden:

data
default
native
management

Erklärung

Frage 69 von 80

1

Refer to the exhibit. A frame is traveling between PC-A and PC-B through the switch. Which statement is true concerning VLAN tagging of the frame?

Wähle eine der folgenden:

A VLAN tag is added when the frame leaves PC-A.
A VLAN tag is added when the frame is accepted by the switch
A VLAN tag is added when the frame is forwarded out the port to PC-B
No VLAN tag is added to the frame.

Erklärung

Frage 70 von 80

1

What must the network administrator do to remove Fast Ethernet port fa0/1 from VLAN 2 and assign it to VLAN 3?

Wähle eine der folgenden:

Enter the no vlan 2 and the vlan 3 commands in global configuration mode
Enter the switchport access vlan 3 command in interface configuration mode.
Enter the switchport trunk native vlan 3 command in interface configuration mode
Enter the no shutdown in interface configuration mode to return it to the default configuration and then configure the port for VLAN 3.

Erklärung

Frage 71 von 80

1

Which two characteristics match extended range VLANs? (Choose two.)

Wähle eine oder mehr der folgenden:

CDP can be used to learn and store these VLANs.
VLAN IDs exist between 1006 to 4094.
They are saved in the running-config file by default.
VLANs are initialized from flash memory
They are commonly used in small networks

Erklärung

Frage 72 von 80

1

A Cisco switch currently allows traffic tagged with VLANs 10 and 20 across trunk port Fa0/5. What is the effect of issuing a switchport trunk allowed vlan 30 command on Fa0/5?

Wähle eine der folgenden:

It allows VLANs 1 to 30 on Fa0/5.
It allows VLANs 10, 20, and 30 on Fa0/5.
It allows only VLAN 30 on Fa0/5.
It allows a native VLAN of 30 to be implemented on Fa0/5

Erklärung

Frage 73 von 80

1

Which command should the network administrator implement to prevent the transfer of DTP frames between a Cisco switch and a non-Cisco switch?

Wähle eine der folgenden:

S1(config-if)# switchport mode trunk
S1(config-if)# switchport nonegotiate
S1(config-if)# switchport mode dynamic desirable
S1(config-if)# switchport mode access
S1(config-if)# switchport trunk allowed vlan none

Erklärung

Frage 74 von 80

1

What is the default DTP mode on Cisco 2960 and 3560 switches?

Wähle eine der folgenden:

dynamic desirable
dynamic auto
trunk
access

Erklärung

Frage 75 von 80

1

Refer to the exhibit. DLS1 is connected to another switch, DLS2, via a trunk link. A host that is connected to DLS1 is not able to communicate to a host that is connected to DLS2, even though they are both in VLAN 99. Which command should be added to Fa0/1 on DLS1 to correct the problem?

Wähle eine der folgenden:

switchport nonegotiate
switchport mode dynamic auto
switchport trunk native vlan 66
switchport trunk allowed vlan add 99

Erklärung

Frage 76 von 80

1

Which two Layer 2 security best practices would help prevent VLAN hopping attacks? (Choose two.)

Wähle eine oder mehr der folgenden:

Change the native VLAN number to one that is distinct from all user VLANs and is not VLAN 1.
Change the management VLAN to a distinct VLAN that is not accessible by regular users.
Statically configure all ports that connect to end-user host devices to be in trunk mode
Disable DTP autonegotiation on end-user ports
Use SSH for all remote management access.

Erklärung

Frage 77 von 80

1

Which two modes does Cisco recommend when configuring a particular switch port? (Choose two.)

Wähle eine oder mehr der folgenden:

access
trunk
FastEthernet
Gigabit Ethernet
ISL
IEEE 802.1Q

Erklärung

Frage 78 von 80

1

In which situation would a technician use the show interfaces switch command?

Wähle eine der folgenden:

to determine if remote access is enabled
when packets are being dropped from a particular directly attached host
when an end device can reach local devices, but not remote devices
to determine the MAC address of a directly attached network device on a particular interface

Erklärung

Frage 79 von 80

1

Which two features on a Cisco Catalyst switch can be used to mitigate DHCP starvation and DHCP spoofing attacks? (Choose two.)

Wähle eine oder mehr der folgenden:

port security
extended ACL
DHCP snooping
DHCP server failover
strong password on DHCP servers

Erklärung

Frage 80 von 80

1

Which two basic functions are performed by network security tools? (Choose two.)

Wähle eine oder mehr der folgenden:

revealing the type of information an attacker is able to gather from monitoring network traffic
educating employees about social engineering attacks
simulating attacks against the production network to determine any existing vulnerabilities
writing a security policy document for protecting networks
controlling physical access to user devices

	Erstellt von Anthony Schulmeister vor fast 11 Jahre