CCNA 3v5.03 Chapter 7

1

Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?

1

What is the purpose of using protocol-dependent modules in EIGRP?

1

If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?

1

Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)

1

Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?

1

What is identified within the opcode of an EIGRP packet header?

1

Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?

1

An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?

1

What information does EIGRP maintain within the routing table?

1

Which table is used by EIGRP to storre all routes that are learned from EIGRP?

1

Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?

1

Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?

1

A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)

1

Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)

1

Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?

1

How do EIGRP routers establish and maintain neighbor relationships?

1

What is indicated when an EIGRP route is in the passive state?

1

What is the multicast address used by an EIGRP-enabled router operating with IPv6?

1

Which configuration is necessary to ensure successful operation of EIGRP for IPv6?

1

Fill in the Blank. Use the abbreviation.

EIGRP uses the protocol to deliver EIGRP packets to neighbors

1

Fill in the blank.

In an EIGRP topology table, a route that is in a/an state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.

1

Match the correct version of EIGRP with the EIGRP features. (Not all options are used.)

EIGRP for IPv4 only

both EIGRP for IPv4 and IPv6

EIGRP for IPv6 only

1

Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.)

_ first _

_ third _

_ second _

1

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

Which code is displayed on the web server?

sophomore CCNA 3 Quiz am CCNA 3v5.03 Chapter 7, erstellt von Christina Evans am 04/07/2016.

CCNA 3v5.03 Chapter 7

Refer to the exhibit. Which command should be used to configure EIGRP to only advertise the network that is attached to the gigabit Ethernet 0/1 interface?

What is the purpose of using protocol-dependent modules in EIGRP?

If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?

Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)

Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?

What is identified within the opcode of an EIGRP packet header?

Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?

An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?

What information does EIGRP maintain within the routing table?

Which table is used by EIGRP to storre all routes that are learned from EIGRP?

Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?

Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?

A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)

Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)

Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?

How do EIGRP routers establish and maintain neighbor relationships?

What is indicated when an EIGRP route is in the passive state?

What is the multicast address used by an EIGRP-enabled router operating with IPv6?

Which configuration is necessary to ensure successful operation of EIGRP for IPv6?

Fill in the Blank. Use the abbreviation.

EIGRP uses the protocol to deliver EIGRP packets to neighbors

Fill in the blank.

In an EIGRP topology table, a route that is in a/an state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.

Which code is displayed on the web server?