CCNA 3 v5.03 Chp 2 ingles

1

What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active alternative physical paths?

1

What additional information is contained in the 12-bit extended system ID of a BPDU?

1

Which three components are combined to form a bridge ID?(Choose three.)

1

Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?

1

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

1

Which is the default STP operation mode on Cisco Catalyst switches?

1

What is an advantage of PVST+?

1

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

1

Which STP priority configuration would ensure that a switch would always be the root switch?

1

To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)

1

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

1

Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?

1

Refer to the exhibit. Which protocol information is being displayed in the output?

1

Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?

1

What value determines the root bridge when all switches connected by trunk links have default STP configurations?

1

Which two concepts relate to a switch port that is intended to have only end devices attached and intended never to be used to connect to another switch? (Choose two.)

1

Which Cisco switch feature ensures that configured switch edge ports do not cause Layer 2 loops if a port is mistakenly connected to another switch?

1

Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby brief command on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?

1

Fill in the blank. Do not abbreviate.
To enable Rapid PVST+ on a Cisco switch, the spanning-tree mode global configuration mode command is required

1

Fill in the blank. Use a number.
The default hello timer value for STP BPDU frames is seconds.

1

Fill in the blank.
In FHRP operation, two or more routers are represented as a single router.

1

Match the spanning-tree feature with the protocol type. (Not all options are used.)

Rapid PVST+

PVST+

RSTP

MSTP

1

Match the step number to the sequence of stages that occur during the HSRP failover process.

Step 1

Step 2

Step 3

Step 4

1

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which switch is the root bridge?

CCNA 3 v5.03 Chp 2 ingles

CCNA 3 v5.03 Chp 2 ingles

CCNA 3 v5.03 Chp 2 ingles

What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active alternative physical paths?

What additional information is contained in the 12-bit extended system ID of a BPDU?

Which three components are combined to form a bridge ID?(Choose three.)

Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?

Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

Which is the default STP operation mode on Cisco Catalyst switches?

What is an advantage of PVST+?

In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

Which STP priority configuration would ensure that a switch would always be the root switch?

To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)

Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?

Refer to the exhibit. Which protocol information is being displayed in the output?

Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?

What value determines the root bridge when all switches connected by trunk links have default STP configurations?

Which two concepts relate to a switch port that is intended to have only end devices attached and intended never to be used to connect to another switch? (Choose two.)

Which Cisco switch feature ensures that configured switch edge ports do not cause Layer 2 loops if a port is mistakenly connected to another switch?

Fill in the blank. Do not abbreviate. To enable Rapid PVST+ on a Cisco switch, the spanning-tree mode global configuration mode command is required

Fill in the blank. Do not abbreviate.
To enable Rapid PVST+ on a Cisco switch, the spanning-tree mode global configuration mode command is required

Fill in the blank. Use a number.
The default hello timer value for STP BPDU frames is seconds.

Fill in the blank.
In FHRP operation, two or more routers are represented as a single router.

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which switch is the root bridge?