Owen Weiss
Quiz by , created more than 1 year ago

Doesn't include intersection, DME, Localizer, or glideslope questions.

62
0
0
No tags specified
Owen Weiss
Created by Owen Weiss over 7 years ago
Close

Jeppesen Chapter 2C

Question 1 of 30

1

When must an operational check on the aircraft VOR equipment be accomplished when used to operate under IFR?

Select one of the following:

  • Within the preceding 10 days or 10 hours of flight time.

  • Within the preceding 30 days or 30 hours of flight time.

  • Within the preceding 30 days.

Explanation

Question 2 of 30

1

Which data must be recorded in the aircraft log or other appropriate log by a pilot making a VOR operational check for IFR operations?

Select one of the following:

  • VOR name or identification, date of check, amount of bearing error, and signature.

  • Place of operational check, amount of bearing error, date of check, and signature.

  • Date of check, VOR name or identification, place of operational check, and amount of bearing error.

Explanation

Question 3 of 30

1

What record shall be made in the aircraft log or other permanent record by the pilot making the VOR operational check?

Select one of the following:

  • The date, place, bearing error, and signature.

  • The date, frequency of VOR or VOT, number of flight hours since last check, and signature.

  • The date, place, bearing error, aircraft total time, and signature.

Explanation

Question 4 of 30

1

Which checks and inspections of flight instruments or instrument systems must be accomplished before an aircraft can be flown under IFR?

Select one of the following:

  • VOR within 30 days, altimeter systems within 24 calendar months, and transponder within 24 calendar months.

  • ELT test within 30 days, altimeter systems within 12 calendar months, and transponder within 24 calendar months.

  • VOR within 24 calendar months, transponder within 24 calendar months, and altimeter system within 12 calendar months.

Explanation

Question 5 of 30

1

When making an airborne VOR check, what is the maximum allowable tolerance between the two indicators of a dual VOR system (units independent of each other except the antenna)?

Select one of the following:

  • 4 degrees between the two indicated bearings of a VOR.

  • Plus or minus 4 degrees when set to identical radials of a VOR.

  • 6 degrees between the two indicated radials of a VOR.

Explanation

Question 6 of 30

1

What minimum navigation equipment is required for IFR flight?

Select one of the following:

  • VOR/LOC receiver, transponder, and DME.

  • VOR receiver and, if in ARTS III environment, a coded transponder equipped for altitude reporting.

  • Navigation equipment appropriate to the ground facilities to be used.

Explanation

Question 7 of 30

1

(Refer to figures 27 and 165)
To which maximum service volume distance from the OED VORTAC should you expect to receive adequate signal coverage for navigation at the flight planned altitude?

Select one of the following:

  • 100NM

  • 80NM

  • 40NM

Explanation

Question 8 of 30

1

(Refer to figure 58)
Which indications on the VOR receivers and DME at the Easterwood Field VOR receiver checkpoint would meet the regulatory requirement for this flight?

Select one of the following:

  • VOR #1...097 FROM; VOR #2...101 FROM; DME...3.3

  • VOR #1...097 TO; VOR#2...096 TO; DME...3.2

  • VOR#1...277 FROM; VOR#2...280 FROM; DME3.3

Explanation

Question 9 of 30

1

(Refer to figure 64)
The course deviation indicators (CDI) are centered. Which indications on the No. 1 and No. 2 VOR receivers over the Lafayette Regional Airport would meet requirements for the VOR receiver check?

Select one of the following:

  • VOR #1...162 TO; VOR#2...346 FROM

  • VOR #1...160 FROM; VOR#2...162 FROM

  • VOR #1...341 FROM; VOR #2...330 FROM

Explanation

Question 10 of 30

1

(Refer to figure 76)
Which indication would be an acceptable accuracy check of both VOR receivers when the aircraft is located on the VOR receiver checkpoint and the Helena Regional Airport?

Select one of the following:

  • A.

  • B.

  • C.

Explanation

Question 11 of 30

1

What is the maximum tolerance allowed for an operational VOR equipment check when using a VOT?

Select one of the following:

  • Plus or minus 4 degrees.

  • Plus or minus 6 degrees.

  • Plus or minus 8 degrees.

Explanation

Question 12 of 30

1

When using VOT to make a VOR receiver check, the CDI should be centered and the OBS should indicate that the aircraft is on the

Select one of the following:

  • 090 radial.

  • 180 radial.

  • 360 radial.

Explanation

Question 13 of 30

1

How should the pilot make a VOR receiver check when the aircraft is located on the designated checkpoint on the airport surface?

Select one of the following:

  • Set the OBS to 180 plus or minus 4 degrees; the CDI should center with a FROM indication.

  • Set the OBS on the designated radial. The CDI must center within plus or minus 4 degrees of that radial with a FROM indication.

  • With the aircraft headed directly toward the VOR and the OBS set to 000, the CDI should center within plus or minus 4 degrees of that radial with a TO indication.

Explanation

Question 14 of 30

1

When the CDI needle is centered during an airborne VOR check, the omnibearing selector and TO/FROM indicator should read

Select one of the following:

  • within 4 degrees of the selected radial.

  • within 6 degrees of the selected radial.

  • 0 degrees TO, only if you are due south of the VOR.

Explanation

Question 15 of 30

1

(Refer to figure 81)
When checking a dual VOR system by use of a VOT, which illustration indicates the VOR's are satisfactory?

Select one of the following:

  • 1.

  • 2.

  • 4.

Explanation

Question 16 of 30

1

While airborne, what is the maximum permissible variation between the two indicated bearings when checking one VOR system against the other?

Select one of the following:

  • Plus or minus 4 degrees when set to identical radials of a VOR.

  • 4 degrees between the two indicated bearings to a VOR.

  • Plus or minus 6 degrees when set to identical radials of a VOR.

Explanation

Question 17 of 30

1

How should the pilot make a VOR receiver check when the aircraft is located on the designated checkpoint on the airport surface?

Select one of the following:

  • With the aircraft headed directly toward the VOR and the OBS set to 000, the CDI should center within plus or minus 4 degrees of that radial with a TO indication.

  • Set the OBS on the designated radial. The CDI must center within plus or minus 4 degrees of that radial with a FROM indication.

  • Set the OBS on 180 plus or minus 4 degrees; the CDI should center with a FROM indication.

Explanation

Question 18 of 30

1

(Refer to figure 82.)
Which is an acceptable range of accuracy when performing an operational check of dual VOR's using one system against the other?

Select one of the following:

  • 1.

  • 2.

  • 4.

Explanation

Question 19 of 30

1

Where can the VOT frequency for a particular airport be found?

Select one of the following:

  • On IAP Chart and in the Airport/Facility Directory

  • Only in the Airport/Facility Directory.

  • In the Airport/Facility Directory and on the A/G Voice Communication Panel of the En Route Low Altitude Chart.

Explanation

Question 20 of 30

1

Which indications are acceptable tolerances when checking both VOR receivers by use of the VOT?

Select one of the following:

  • 360 TO and 003 TO, respectively.

  • 001 FROM and 005 FROM, respectively.

  • 176 TO and 003 FROM, respectively.

Explanation

Question 21 of 30

1

In which publication can the VOR receiver ground checkpoint(s) for a particular airport be found?

Select one of the following:

  • Airman's Information Manual

  • En Route Low Altitude Chart.

  • Airport/Facility Directory.

Explanation

Question 22 of 30

1

Which is the maximum tolerance for the VOR indication when the CDI is centered and the aircraft is directly over the airborne checkpoint?

Select one of the following:

  • Plus or minus 6 degrees of the designated radial.

  • Plus 6 degrees or minus 4 degrees of the designated radial.

  • Plus or minus 4 degrees of the designated radial.

Explanation

Question 23 of 30

1

When making an airborne VOR check, what is the maximum allowable tolerance between the two indicators of a dual VOR system (units independent of each other except the antenna)?

Select one of the following:

  • 4 degrees between the two indicated radials of a VOR.

  • Plus or minus 4 degrees when set to identical radials of a VOR.

  • 6 degrees between the two indicated radials of a VOR.

Explanation

Question 24 of 30

1

Which distance is displayed by the DME indicator?

Select one of the following:

  • Slant range distance in NM.

  • Slant range distance in SM.

  • Line of sight direct distance from aircraft to VORTAC in SM.

Explanation

Question 25 of 30

1

Where does the DME indicator have the greatest error between ground distance to the VORTAC and displayed distance?

Select one of the following:

  • High altitudes far from the VORTAC.

  • High altitudes close to the VORTAC.

  • Low altitudes far from the VORTAC.

Explanation

Question 26 of 30

1

For operations off established airways at 17,000 feet MSL in the contiguous U.S> (H) Class VORTAC facilities used to define a direct route of flight should be no farther apart than

Select one of the following:

  • 75NM.

  • 100NM.

  • 200NM.

Explanation

Question 27 of 30

1

What indication should a pilot receive when a VOR station is undergoing maintenance and may be considered unreliable?

Select one of the following:

  • No coded identification, but possible navigation indications.

  • Coded identification, but no navigation indications.

  • A voice recording on the VOR frequency announcing that the VOR is out of service for maintenance.

Explanation

Question 28 of 30

1

A particular VOR station is undergoing routine maintenance. This is evidenced by

Select one of the following:

  • removal of the navigational feature.

  • broadcasting a maintenance alert signal on the voice channel.

  • removal of the identification feature.

Explanation

Question 29 of 30

1

What is the meaning of a single coded identification received only once approximately every 30 seconds from a VORTAC?

Select one of the following:

  • The VOR and DME components are operative.

  • VOR and DME components are both operative, but voice identification is out of service.

  • The DME component is operative and the VOR component is inoperative.

Explanation

Question 30 of 30

1

Which DME indication should you receive when you are directly over a VORTAC site at approximately 6,000 feet AGL.

Select one of the following:

  • 0.

  • 1.

  • 1.3

Explanation

Previous
Next