Unit 205: Cold water systems - practice test

1

When installing a new indirect cold water system, which of the following should
happen, according to the Water Regulations?

1

When installing a new indirect cold water system, which of the following should
happen, according to the Water Regulations?

1

According to BS6700 and the Water Regulations, a drain off valve should be
installed:

1

According to BS6700 and the Water Regulations, a drain off valve should be
installed:

1

Pin holing in copper pipework is commonly caused by:

1

Pin holing in copper pipework is commonly caused by:

1

While installing pipework in a property, you are called off site to another job. What
would be the correct course of action with any open-ended pipework?

1

While installing pipework in a property, you are called off site to another job. What
would be the correct course of action with any open-ended pipework?

1

One of the major problems when leaving a dead leg in a cold water pipe is:

1

One of the major problems when leaving a dead leg in a cold water pipe is:

1

The use of WRAS approved fittings when installing cold water pipework is:

1

The use of WRAS approved fittings when installing cold water pipework is:

1

On the completion of a new cold water installation, the system has been proven
sound. What would the next course of action be?

1

On the completion of a new cold water installation, the system has been proven
sound. What would the next course of action be?

1

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

1

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

1

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

1

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

1

When decommissioning a system, the correct procedure is to:

1

When decommissioning a system, the correct procedure is to:

1

When decommissioning a system, the correct procedure is to:

1

When decommissioning a system, the correct procedure is to:

1

What is this item?

1

What is this item?

1

What is this item?

1

What is this item?

1

What type of valve is shown in this diagram?

1

What type of valve is shown in this diagram?

1

What type of valve is shown in this diagram?

1

What type of valve is shown in this diagram?

1

When installing a new water service pipe to a property, it should
normally be buried between what depths?

1

When installing a new water service pipe to a property, it should
normally be buried between what depths?

1

When installing a new water service pipe to a property, it should
normally be buried between what depths?

1

When installing a new water service pipe to a property, it should
normally be buried between what depths?

1

Identify item C in the diagram.

1

Identify item C in the diagram.

1

Identify item C in the diagram.

1

Which of the following materials is not allowed
to be installed on new cold water systems?

1

Which of the following materials is not allowed
to be installed on new cold water systems?

1

What type of valve is designed to shut off the supply of water in a cistern at a
predetermined level?

1

The fluid category that offers a slight health risk to a customer is:

1

The correct back flow protection device that would be installed prior to a shower
mixer valve would be:

1

To protect category 1 water from category 3 water, what would need to be installed,
according to the Water Regulations?

1

What would this item be used to test?

1

If a customer’s tap is dripping, what tool can be used to correct the situation?

A cold water practice exam

Unit 205: Cold water systems - practice test

Unit 205: Cold water systems - practice test

When installing a new indirect cold water system, which of the following should happen, according to the Water Regulations?

When installing a new indirect cold water system, which of the following should happen, according to the Water Regulations?

According to BS6700 and the Water Regulations, a drain off valve should be installed:

According to BS6700 and the Water Regulations, a drain off valve should be installed:

Pin holing in copper pipework is commonly caused by:

Pin holing in copper pipework is commonly caused by:

While installing pipework in a property, you are called off site to another job. What would be the correct course of action with any open-ended pipework?

While installing pipework in a property, you are called off site to another job. What would be the correct course of action with any open-ended pipework?

One of the major problems when leaving a dead leg in a cold water pipe is:

One of the major problems when leaving a dead leg in a cold water pipe is:

The use of WRAS approved fittings when installing cold water pipework is:

The use of WRAS approved fittings when installing cold water pipework is:

On the completion of a new cold water installation, the system has been proven sound. What would the next course of action be?

On the completion of a new cold water installation, the system has been proven sound. What would the next course of action be?

What is the most cost effective way to repair a stop valve that has the head gear jammed open?

What is the most cost effective way to repair a stop valve that has the head gear jammed open?

What is the most cost effective way to repair a stop valve that has the head gear jammed open?

What is the most cost effective way to repair a stop valve that has the head gear jammed open?

When decommissioning a system, the correct procedure is to:

When installing a new indirect cold water system, which of the following should
happen, according to the Water Regulations?

When installing a new indirect cold water system, which of the following should
happen, according to the Water Regulations?

According to BS6700 and the Water Regulations, a drain off valve should be
installed:

According to BS6700 and the Water Regulations, a drain off valve should be
installed:

While installing pipework in a property, you are called off site to another job. What
would be the correct course of action with any open-ended pipework?

While installing pipework in a property, you are called off site to another job. What
would be the correct course of action with any open-ended pipework?

On the completion of a new cold water installation, the system has been proven
sound. What would the next course of action be?

On the completion of a new cold water installation, the system has been proven
sound. What would the next course of action be?

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

What is the most cost effective way to repair a stop valve that has the head gear
jammed open?

When installing a new water service pipe to a property, it should
normally be buried between what depths?

When installing a new water service pipe to a property, it should
normally be buried between what depths?

When installing a new water service pipe to a property, it should
normally be buried between what depths?

When installing a new water service pipe to a property, it should
normally be buried between what depths?