3720702
Pregunta 1
Pregunta
You have configured your Cisco TelePresence Codec C90 but discover unwated noise during use. What best practice will help avoid this problem.
Respuesta
-
Connect only one device at a time ot an input and avoid daisy -chaining
-
Recycle the power on your system after adding each additional input
-
If you are not using an input, turn it off.
-
Daisy-chain additional devices using a serial cable to provide separate power supplies
Pregunta 2
Pregunta
Which two letters represent input connections on the Cisco Telepresence codec c90
Respuesta
-
A
-
B
-
C
-
D
Pregunta 3
Pregunta
You want to reconfigure the H.323 and Sip settings using the remote control on the Cisco TelePresence Codec C90. Which menu allows you to do this?
Respuesta
-
Audio input levels
-
IP Settings
-
Advanced Configuration
-
protocol configuration
Pregunta 4
Pregunta
What do you need to do before an endpoint can place or receive H.323 calls using a URL address
Respuesta
-
Register the endpoint to the SIP server
-
Register the endpoints to the gatekeeper
-
Register the endpoint to the gatway
-
Register the endpoint to the Cisco TelePresence MCU
Pregunta 5
Pregunta
You are installing a high-definition (720p or 1080p) monitor on the Cisco TelePresence Codec C90. Which of the outputs that are represented by letters in the exhibit should you use.
Respuesta
-
A or B
-
A or D
-
A or E
-
B or C
-
D or E
Pregunta 6
Pregunta
While on a call, using the remote control, how do you add an additional participant to a call on your MultiSite-enabled endpoint?
Respuesta
-
Press the home button to return to the menu, and select the add participant button
-
Press and hold the End Call key to bring up the dialing menu.
-
Press and hold the Call key to bring up the dialing menu
-
Press the Call key, and choose or dail the number of the additional participant
Pregunta 7
Pregunta
Which three are true statements regarding the Cisco TelePresence endpoint product set? (Choose 3)
Respuesta
-
The MX200 and MX300 are all-inclusive systems and do not require additional AV components
-
The MX200 and MX300 are integrator codec systems and require additional AV components
-
The EX60 and EX90 are room-based TelePresence systems intended for use in board rooms
-
The C90 is a high end integrator codec
-
The EX90 is an integrator codec
-
The C40 is a basic integrator codec supporting dual monitors
Pregunta 8
Pregunta
What are the two methods for pairing an 8-inch Cisco Telepresence touch panel to a Codec C90? ( Choose two)
Respuesta
-
Plug the cable that is attached to the Touch panel directly into the back of the Codec C90
-
Plug the provided Ethernet cable from the Touch panel power supply into the second Ethernet port on the Codec C90
-
Plug the provided Ethernet cable from the Touch panel power supply into the Lan and pair over the network.
-
Use the built-in wireless on the Touch panel to pair over the network
Pregunta 9
Pregunta
Which statement is true regarding passwords on a Cisco TelePresence MX, EX, C Series or SX20 device?
Respuesta
-
The device ships from factory with the admin account enabled, with no password
-
The device ships from factory with the admin account enabled, with a default password of Cisco.
-
The device ships from factoractory with admin account enabled, with a default password of tandberg
-
The devices ships from factory with the root account enabled, with no password
Pregunta 10
Pregunta
When configuring a Cisco TelePresence EX, MX, or C Series devices, which two statements are true? (Chose two)
Respuesta
-
The unit can be completely configured from the web interface.
-
If available, the TRC5 remote control can be used to completely configure the unit
-
The API must be used in order to configure the unit
-
The Touch panel can be used to completely configure the unit.
Pregunta 11
Pregunta
If the user purchases the Cisco TelePresence touch panel, which two statements are true? (Choose Two)
Respuesta
-
Both the TRC5 remote and the Touch panel can be used simultaneously.
-
Either the TRC5 remote control or the Touch panel can be used, but not both simultaneously
-
The Touch panel should be used to make calls, but the TRC5 remote control should be used to configure the unit.
-
The web interface can be used to configure the unit
Pregunta 12
Pregunta
If you do not have the Premium Resolution option installed on a Cisco TelePresence endpoint, what is the maximum resolution that you can transmit and receive?
Respuesta
-
1080p30
-
720p60
-
720p30
-
Standard definition resolutions only
Pregunta 13
Pregunta
When using the Cisco TelePresence Touch panel with a Codec C90, which administrator setting can you access?
Respuesta
-
all of the same administrator settings as when using the TRC5 remote.
-
a limited subset of the administrator settings compared with using the TRC5 remote
-
none of the Administrator settings
-
only the custom video layout settings
Pregunta 14
Pregunta
What can you see on the Status > Registrations > by device page?
Respuesta
-
currently registered SIP and H.323 devices
-
all devices that were registered for SIP or H.323 since the last reboot
-
currently registered H.323 devices only
-
Currently registered SIP devices only
Pregunta 15
Pregunta
Which two settings can be configured using the serial connection when you are running the TelePresence VCS install wizard? (Choose 2)
Respuesta
-
Device name
-
device ID number
-
IP address
-
password
-
default video codec
Pregunta 16
Pregunta
Which feature or features will work on a new Cisco telePresence VCS as soon as the ip configuration is done.
Respuesta
-
H.323
-
H.323 and SIP
-
H323, SIP, and interworking
-
H.323, SIP, Interworking, and firewall traversal
Pregunta 17
Pregunta
Which of these options shows the methods that are available to configure a Cisco VCS appliance at initial installation
Respuesta
-
CLI over serial port, web interface keyboard and monitor
-
CLI over serial port, web interface, LCD panel
-
CLI over serial port, web interface, boot disk
-
Using the Cissco Prime Collaboration Manager, after running System Discovery, to discovery the newly added Cisco VCS
Pregunta 18
Pregunta
The Cisco VCS Starter Pack Express supports which two features that are not found in a Cisco VCS Control? (Choose two)
Respuesta
-
jabber for Ipad support
-
Expressway server
-
local device authentication
-
built-in provision
Pregunta 19
Pregunta
In the SIP configuration, which two items need to match in the Cisco TelePresence VCS configuration and the endpoint configuration? ( Choose two)
Respuesta
-
Service Prefix
-
Cisco VCS IP address
-
DNS Server
-
SIP domain
Pregunta 20
Pregunta
Which two inter-working functions are supported on the Cisco VCS (Choose Two)
Respuesta
-
SIP-to-H.323
-
IPv4-to-IPv6
-
H.323-to-H.320
-
firewall traversal
Pregunta 21
Pregunta
Which statement is true when the H.323 and SIP inter working is set to on in the Cisco TelePresence VCS?
Respuesta
-
The Cisco TelePresence VCS will act as a SIP-to-H.323 gateway regardless of whether one of the end points is locally registered.
-
The Cisco TelePresence VCS will act as a SIP-to-H.323 gateway only if one of the endpoints is locally registered.
-
The Cisco TelePresence VCS will not act as a SIP-to-H.323 gateway.
-
The Cisco TelePresence VCS will permit all traffic from any H.323 or SIP endpoint that is registered locally
Pregunta 22
Pregunta
Which type of account needs to be set up to create a Csico TelePresence soft client (such as Cisco Jabber or Movi)user if you are using the Cisco TelePresence VCS Expressway Starter Pack?
Respuesta
-
a local FindMe account on the Cisco VCS
-
a local admin account on the Cisco VCS
-
an LDAP user account on Active Directory
-
an LDAP FindMe account on Active Directory
Pregunta 23
Pregunta
Which of these must be enabled to set up a Cisco TelePresence soft client (such Cisco Jabber or Movi) on a Cisco TelePresence VCS Expressway Starter Pack?
Respuesta
-
SIP
-
H.323
-
Interworking
-
Multiway
Pregunta 24
Pregunta
Which two of these are required for restoring a backup to another Cisco VCS? (Choose Two)
Respuesta
-
The same version of software of as the original Cisco VCS
-
the same basic IP address settings
-
an empty configuration on the Cisco vcs
-
the same option keys
Pregunta 25
Pregunta
How are firewall traversal connections established between the Cisco TelePresence VCS expressway and Control?
Respuesta
-
The traversal client establishes connections outbound to the traversal server
-
The traversal server establishes connections inbound to the traversal client
-
Connections are established in both directions from the traversal server to the traversal client
-
The traversal server nogotiaties acceptable connection prots with the firewall
Pregunta 26
Pregunta
Which command is used to set the IP configuration for a Cisco TelePresence MCU 5300
Respuesta
-
Status IP address netmask default GW
-
xconfigure IP addresss netmask default GW
-
static A IP address netmask default GW
-
set IP address netmask default GW DNS server address
Pregunta 27
Pregunta
If the zone is a VCS firewall traversal solution are established, what else is needed before connections can be established in both directions?
Respuesta
-
A call policy must be established
-
VCS serach rules must be created for each zone
-
The VCS control and the VCS expressway must be neightbored
-
Transforms must be created in the VCS traversal server zone
Pregunta 28
Pregunta
What does an endpoint sysrtem user to navigate the Auto Attendant menu on the Cisco TelePresence MCU?
Respuesta
-
FECC or DTMF navigation
-
a special remote that came with the Cisco TelePresence MCU
-
Only FECC; DTMF is not supported
-
web interafce of the endpoint
Pregunta 29
Pregunta
If an auto attendant has a numeric id of 543 and the Cisco TelePresence MCU has a prefix of 62 and a domain of cisco.demo, which two of these will be registered on the Cisco TelePresence VCS, assuming that SIP and H.323 registration have been selected? (Choose two)
Respuesta
-
62543
-
543@cisco.demo
-
543
-
62543@cisco.demo
-
543@62.cisco.demo
Pregunta 30
Pregunta
How can you register a prefix to route all SIP calls beginning with that prefix to the Cisco TelePresence MCU?
Respuesta
-
You cannot; all SIP addresses must be registered individually
-
The H.323 prefix is automatically used
-
You cannot; you need to use a suffix in the form of a domain.
-
The username is used as the suffix
Pregunta 31
Pregunta
What does the Cisco Telepresence MCU service prefix do?
Respuesta
-
Ensures that all H.323 calls beginning with perfix are routed to the Cisco TelePresence MCU
-
is added to all aliases before registration
-
diverts calls to the default auto attendant
-
identifies which serves the Cisco TelePresence MCU will offer in each configured meeting room
Pregunta 32
Pregunta
How does an administrator move an endpoint efficiently from one conference to another Cisco TelePresence MCU ?
Respuesta
-
From the Move Participants screen, right-click the participant and select the new conference from the drop-down list
-
From the Move Participants screen, drag and drop a participant from once conference to another
-
From the Conference menu, select the participant, and then select the new conference
-
From the web interace, disconnect the participant, and then reconnect to the new conference.
Pregunta 33
Pregunta
By which two ways can an endpoint join a conference on the Cisco TelePresence MCU ? (Choose two)
Respuesta
-
dialing a registered alias for the conference
-
dialing the auto attendant and navigating to the conference
-
dialing an endpoint that is already in the conference
-
dialing all endpoints that are required in the conference
-
dialing the PIn number of the conference
Pregunta 34
Pregunta
What effect does the 'Prefix for MCU Registration' have on Cisco TelePresence MCU registration?
Respuesta
-
The prefix replaces the domain if the prefix is dialed
-
The prefix is placed in front of all SIP URI's
-
Anything that is dialed with the perfix will be routed to the Cisco TelePresence MCU
-
The prefix is placed in front of all E.164 aliases
Pregunta 35
Pregunta
What is the maximum port capacity of the 5320 MCU?
Respuesta
-
5HD+ OR 10HD OR 20SD OR 24nhd
-
1HD+ or 2HD or 4SD or 8nHD
-
10HD+ or 20HD or 40SD or 48nHD
-
20HD+ or 40HD or 80SD or 96nHD
Pregunta 36
Pregunta
How many rack units does a Cisco TelePresence MCU 5300 occupy in a standard data center
Respuesta
-
1
-
2
-
3
-
4
Pregunta 37
Pregunta
Using the web interface, where can you verify the licensing on a Cisco TelePresence MCU 5300?
Respuesta
-
Settings > Upgrade
-
Settings > Conference
-
Settings > Content
-
Status > Help
Pregunta 38
Pregunta
How many endpoints can register to the built-in H.323 gatekeeper of a Cisco TelePresence MCU 5300 series device.
Respuesta
-
none; there is no built-in gatekeeper
-
25
-
100
-
300
Pregunta 39
Pregunta
How should you configure the IP address and default gateway on a Cisco TelePresence MCU 53000 Series device during setup
Respuesta
-
Conenct an Ethernet cable to the second Ethernet port of the MCU, and point your web browser to 192.168.2.2
-
Console into the serial port in the front panel, and use the static command
-
Use the arrows next to the LCD in the front to change the IP address, subnet mask, and default gateway
-
change it from the Cisco VCS
Pregunta 40
Pregunta
How do you upgrade the software of an exisiting installtion with a Cisco TelePresence MCU 5300?
Respuesta
-
Download the new software, navigate to Maintenance > Upgrade Software, and upload the software
-
Use FTP to access the MCU, browse to the etc/software/upgrade directory, put the new load in and reboot the MCU
-
Navigate to Settings > Upgrade, then follow instructions under Main Software Image.
-
Use an SFTP client to log into the MCU, and place the software in the etc/software/upgrade directory
Pregunta 41
Pregunta
How to you obtain a SIP log from the Cisco TelePresence MCU 5300 to send to Cisco TAC for futher analysis?
Respuesta
-
Navigate to Maintenance > Logs, and the download the log
-
Navigate to Logs > Event Log > SIP Details, and the download the log
-
Navigate to Logs > H.323/SIP Log, click Enable H.323/SIP Logging, and then download the log.
-
Use FTP to access the MCU, go to the directory /etc/logs/sip, and get all of the files in the directory.
Pregunta 42
Pregunta
What is one way that a conference participants screen layout be changed without affecting other participants
Respuesta
-
Via the participant settings in the MCU 5300 web interface
-
via the conference settings in the MCU 5300 web interface
-
by the nominated chair endpoint using FECC
-
by moving the participant into a different meeting using the MCU 5300 web interface
Pregunta 43
Pregunta
What are two ways that a conference participant can be disconnected from a conference? (Choose Two)
Respuesta
-
by using the MCU 5300 web interface
-
will be automatically disconnected at the end of the allotted time
-
by the auto attendant
-
will be disconnected when the conference exceeds its maximum capacity.
Pregunta 44
Pregunta
Before you upgrade your Cisco TelePresence Management Suite, what should you do with your SQL database?
Respuesta
-
Save a backup
-
Restore a previous version
-
Set a new username and password
-
Create a second copy
Pregunta 45
Pregunta
Which installation option should you choose if you wish to use an external SQL database?
Respuesta
-
Complete
-
Custom
-
Advanced
-
Basic
Pregunta 46
Pregunta
If you do not have a valid release key, what restrictions will be applied?
Respuesta
-
The Cisco TelePresence Management Suite will only manage three systems
-
Installation will fail and the Cisco TelePresence Management Suite will not be installed
-
The Cisco TelePresence Management Suite will only operate for 30 days
-
The SQL database will be purged every 30 days.
Pregunta 47
Pregunta
Where would you enter release and option keys into the Cisco TelePresence Management Suite
Respuesta
-
in Configuration>General Settings
-
On the portal page
-
through the release key generator in a terminal session on the server
-
on the Cisco TelePresence Manager Suite server maintenance page
Pregunta 48
Pregunta
When a new conference is booked on the Cisco TelePresence Management Suite, which setting instructs the endpoint or Cisco TelePresence MCU to call a participant at the time of a conference
Respuesta
-
Manual
-
Call-in Only
-
Reverse Call
-
Automatic
Pregunta 49
Pregunta
By which three ways can systems be added in the Cisco TelePresence Management Suite? (Choose three)
Respuesta
-
by preregistering systems
-
from a .csv file
-
by importing from a Cisco TelePresence VCS
-
by user-configured name
-
by dialing an endpoint
-
by IP address.
-
from a list of previously discovered systems
Pregunta 50
Pregunta
You want to obtain specific configuration details from each of the systems that are regisitered to your Cisco TelePresence Management Suite. Where can you do this ?
Respuesta
-
Choose Navigator from the Systems menu
-
Choose System Overview from the System menu
-
Run System tracking from the systems menu
-
Connect to the Cisco TelePresence Management Suite via a console connection and use show commands
Pregunta 51
Pregunta
After you create a phone book in the Cisco TelePresence Management Suite, which method should you use to populate it with entries
Respuesta
-
Connect the phone book to a phone book source
-
Manually type entries into the phone book.
-
Connect the phone book to a gatekeeper
-
Upload a file in .mdf format
Pregunta 52
Pregunta
The Cisco TCS provides which two functions ? (Choose two)
Respuesta
-
records and standards-based video conferencing session
-
records video from IP-based encoders
-
can stream out live TelePresence sessions over IP networks
-
allows users to upload video for conversion into H.264 or MP4
Pregunta 53
Pregunta
Which two statements about the Cisco TCS are correct? ( Choose two)
Respuesta
-
It contains an internal gatekeeper
-
it allows creators to edit videos
-
it runs on the window operating system
-
it runs on the linux operating systems
Pregunta 54
Pregunta
What are two ways to set the IP netowrk information on the CIsco TCS? (Choose two)
Respuesta
-
DHCP
-
statically set on its windows operating system
-
statically set on its linux operating system
-
automatically assigned by the cisco telepresence managment server
Pregunta 55
Pregunta
What is the effect of registering the Cisco TCS with the Cisco VCs using H.323 gateway mode?
Respuesta
-
The Cisco TCS does not support this type of registration.
-
An unlimited number of recording aliases can be assigned
-
The cisco tcs is prevent from making an outbound call to a Cisco MCU
-
The Cisco TCS can reaverse calls between SIP and H.323
Pregunta 56
Pregunta
Which two statments about Cisco TCS recording aliases are true? ( Choose two)
Respuesta
-
System recording aliases can only be dialed by the site manager (administrator)
-
Any recording alias can be triggered by dialing its assigned URI or E.164 number
-
Recordings resulting from a personal recording alias can only be managed by their creator.
-
final recordings made from a recording alias cannot be modified
Pregunta 57
Pregunta
Which of these constitutes a Cisco TCS recording alias?
Respuesta
-
A recording template, a media server configuration, and a call configuration.
-
a media server configuration and a call configuration
-
a recording template and a media server configuration
-
a recording template and a call configuration
Pregunta 58
Pregunta
Which two statements about Cisco TCS users are true? (Choose two)
Respuesta
-
Users with the creator role can create their won recording aliases
-
Local users have only limited Cisco TCS permissions
-
Users can be assigned to the Cisco TCS through an Active Directory LDAP server
-
User permissions are based on one of three assignable roles
Pregunta 59
Pregunta
Which two statements about Cisco TCS recording templates are true? (Choose Two)
Respuesta
-
Every recording alias contains one recording template
-
They provide a way to produce recordings without a recording alias
-
They must always contain a media server configuration
-
There can only be one system recording template
Pregunta 60
Pregunta
Which statement about playing back Cisco TCS recording is true ?
Respuesta
-
It is not possible to play back Cisco TCS recordings from a video enpoint
-
The Cisco TCS must register to the Cisco VCS as an H.323 gateway in order to play back recordings on video endpoints
-
The Cisco TCS will automatically assign an E.164 playback number to recordings if it is registered as an H.323 terminal
-
The Cisco TCS must register to the Cisco VCS using SIP in order to play back on any video endpoint
Pregunta 61
Pregunta
In which two locations can Cisco TCS recordings be view? ( Choose two)
Respuesta
-
directly on the cisco TCS web portal
-
in the Cisco TelePresence Managements server
-
on a video endpoint
-
on the Codec C90 touch panel
Pregunta 62
Pregunta
Which two pieces of troubleshooting information does the Cisco TCS provide? ( Choose two)
Respuesta
-
log messages that can be accessed by the site manager through the CLI
-
recording alias processing progress
-
error logs that only Cisco TAC can access
-
log messages that can be accessed by the site manager through the web interface
Pregunta 63
Pregunta
Which two of these can be found by navigating to TCS Diagnostic > Server Overview in the cisco TCS web interface? ( Choose Two)
Respuesta
-
option key information
-
recording port activity status
-
Cisco VCS registration status
-
which cisco tms is managing the TCS
Pregunta 64
Pregunta
Cisco TCS recordings can be encoded into which two video formats? ( Choose two)
Respuesta
-
MPEG-4 for flash and QuickTime
-
WMV
-
H.262
-
Sorensen VP8 for flash
¿Quieres crear tus propios Tests gratis con GoConqr? Más información.