Pregunta 1
Pregunta
The low pressure end of a turbine may be protected from over pressure protection by an atmospheric relief valve and/or
Respuesta
-
overspeed trip
-
explosion diaphragm
-
vacuum trip relay
-
vibration monitors
-
noise muffler
Pregunta 2
Pregunta
condensers may be divided into two basic groups namely,
Respuesta
-
direct and indirect
-
jet and surface
-
atmospheric and vacuum
-
contact and surface
-
evaporative and spray
Pregunta 3
Pregunta
Jet condensers are in limited use today mainly due to:
Pregunta 4
Pregunta
Condenser waterboxes are typically made from:
Respuesta
-
carbon steel
-
stainless steel
-
cast iron
-
aluminum
-
nickel or brass
Pregunta 5
Pregunta
condenser tube sheets are typically made from
Respuesta
-
carbon steel
-
stainless steel
-
cast iron
-
aluminum
-
admiralty brass
Pregunta 6
Pregunta
A large heating surface is utilized in a surface condenser for maximum efficiency. This is largely done by:
Respuesta
-
putting in as many tubes as possible
-
using large diameter tubes
-
using small diameter tubes
-
using stainless steel tubes
-
none of the above
Pregunta 7
Pregunta
To allow for differential expansion for the shell and tubes in a condesnser, which of the following methods may be used:
1. tube packing 2. expansion bends. 3. elastic materials 4. expansion joints to the shell 5. solid weld construction 6. slip expansion tubes
Pregunta 8
Pregunta
Safety fittings on a condenser may include
1. gage glass
2. relief valve
3. corrosion coupons
4. low water alarm
5. vacuum trip relay
6. leak detection devices
Respuesta
-
1,2,3,4,5
-
1,2,5
-
1,2,4,5
-
1,2,3,5
-
2,3,4,5
Pregunta 9
Pregunta
The main purpose of waterbox staybolts is to
Respuesta
-
support the tubesheet from cooling water pressure
-
support the tube sheet from condenser vacuum
-
prevent the condenser tubes from buckling
-
act as a sacrificial corrosion coupon
-
all of the above
Pregunta 10
Pregunta
non condensables in a condenser must be removed largely due to
Respuesta
-
the blanketing effect on the tubes
-
tube pitting
-
increase the condensate ph
-
lowers the condensate ph
-
increases the condenser vacuum
Pregunta 11
Respuesta
-
increases the vacuum on a turbine condenser
-
prevents non-condensable gasses from entering the condenser
-
converts heat energy into kinetic energy
-
utilizes a vacuum pump
-
may also be termed hogging ejector
Pregunta 12
Pregunta
The larges single heat loss in a steam power cycle is:
Pregunta 13
Pregunta
Air that enters a surface condenser:
Respuesta
-
causes pitting on the cooling water tubes
-
will increase the condenser pressure
-
will cause the condensate to turn slightly acidic and cause corrosion
-
will cavitate the extraction pump
-
has no effect on the operation of the plant
Pregunta 14
Pregunta
the best test method to detect condenser cooling water leaks is
Respuesta
-
conductivitity
-
ph
-
silica
-
phosphate
-
color comparator
Pregunta 15
Pregunta
In a surface condenser:
1. packed tube ends allows the tube to move axially in the packing
2. deaeration is less efficient when the condensate is sub-cooled
3. there is no temperature differential expansion
4. when the inlet of the tube is exposed, it is also beaded over to prevent leakage
Respuesta
-
1,2,3
-
1,2,4,
-
1,2
-
3,4
-
1,2,3,4
Pregunta 16
Pregunta
Prior to starting a large condensing turbine:
Respuesta
-
the jacking oil pump is started after the turbine has been put on barring
-
open all steam trap bypass valves
-
turn on oil coolers cooling water prior to firing up the boiler
-
put the condenser into operation
-
test the turbine overspeed trips