nicilynn1981
Quiz by , created more than 1 year ago

CDC 2A652N - Volume 1 - Maintenance & Fundamentals

35
1
0
nicilynn1981
Created by nicilynn1981 over 8 years ago
Close

CDC 2A652N - Volume 1 - Maintenance & Fundamentals

CDC 2A652N - Volume 1 - Maintenance & Fundamentals

Question 1 of 73

1

Risk management principles should be applied to

Select one of the following:

  • Only duty-related activities to enhance the safety and well-being of yourself and others.

  • On- and off-duty activities to enhance the safety and well-being of yourself and others.

  • Only duty-related activities to protect yourself and other Airmen from imminent harm.

  • On- and off-duty activities to protect yourself and other Airmen from imminent harm.

Explanation

Question 2 of 73

1

What situation does not warrant prompt reporting to your supervisor?

Select one of the following:

  • Using personal protective equipment.

  • Unsafe working conditions.

  • Known pregnancies.

  • Personal injury.

Explanation

Question 3 of 73

1

Before removing a component from an air compressor, you must ensure

Select one of the following:

  • The air compressor is grounded.

  • The air strainer is in place.

  • The battery is disconnected.

  • All air pressure is drained.

Explanation

Question 4 of 73

1

Why should the frame of an electrical motor be grounded?

Select one of the following:

  • To prevent the energized windings from touching the frame.

  • To prevent current from following the path of least resistance.

  • To prevent you from receiving an electrical shock if the energized windings touch the frame.

  • To prevent current from flowing directly to ground if the energized windings touch the frame.

Explanation

Question 5 of 73

1

Which type of hammer should you use to avoid damaging driving materials?

Select one of the following:

  • Claw

  • Sledge

  • Soft face

  • Ball-peen

Explanation

Question 6 of 73

1

Which type of screwdriver has blades designed to lessen the possibility of the screwdriver slipping from the screw head?

Select one of the following:

  • Cross-point.

  • Flat-blade.

  • Cross-tip.

  • Offset

Explanation

Question 7 of 73

1

Which pliers should be used to hold odd-shaped objects?

Select one of the following:

  • Snap ring.

  • Diagonal cutting.

  • Multiple slip-joint.

  • Combination slip-joint

Explanation

Question 8 of 73

1

Which pliers have a locking device to hold materials securely?

Select one of the following:

  • Snap ring.

  • Vice grips.

  • Water pump.

  • Diagonal cutters.

Explanation

Question 9 of 73

1

Diagonal cutting pliers are designed to cut

Select one of the following:

  • Bolts

  • Rivets

  • Hard steel

  • Small wire

Explanation

Question 10 of 73

1

Before operating the pneumatic impact wrench, you must

Select one of the following:

  • Inspect it

  • Lubricate it

  • Blow out the air hose

  • Ensure that its use is necessary

Explanation

Question 11 of 73

1

Replacement hardware decisions on support equipment must be governed by

Select one of the following:

  • Supervisor's preference

  • Serviceablility criteria

  • Cosmetic appearance

  • Availability

Explanation

Question 12 of 73

1

What type of bolt is typically used to connect accessories to an engine?

Select one of the following:

  • Stud

  • Fine thread bolt

  • Coarse thread bolt

  • General purpose bolt

Explanation

Question 13 of 73

1

What type of nut should never be used in areas where the temperature exceeds 250 degrees Fahrenheit?

Select one of the following:

  • Nonmetallic self-locking nuts

  • Metallic self-locking nuts

  • Castellated nuts

  • Plain nuts

Explanation

Question 14 of 73

1

What color code is used on pre-insulated terminal lugs for wire sizes 18 through 22?

Select one of the following:

  • Red

  • Blue

  • Green

  • Yellow

Explanation

Question 15 of 73

1

What are the three different types of terminal lugs?

Select one of the following:

  • Red, Blue & Yellow

  • Straight, Right Angle & Flat

  • Copper, Aluminum & Plastic

  • Pre-insulated, uninsulated & reinsulated

Explanation

Question 16 of 73

1

What does the “-4” identify in fitting part number MS20822-4D?

Select one of the following:

  • Military specification

  • Type of fitting

  • Air Force/Navy

  • Fitting size

Explanation

Question 17 of 73

1

What type of damage greatly reduces the ability of tubing to withstand internal pressure and vibration?

Select one of the following:

  • Scratches

  • Chafing

  • Dents

  • Nicks

Explanation

Question 18 of 73

1

A flexible hose in a 3,000 psi system must be pressure tested to

Select one of the following:

  • 3,000 psi without bursting

  • 9,000 psi without bursting

  • 12,000 psi without bursting

  • 15,000 psi without bursting

Explanation

Question 19 of 73

1

When installing a flexible hose, you must provide slack or bend in the hose to

Select one of the following:

  • Prevent twisting of the hose

  • Compensate for change in length

  • Place a mechanical load on the hose

  • Protect it from a hot pipe or manifold

Explanation

Question 20 of 73

1

How can people best prevent FOD?

Select one of the following:

  • Look for loose objects (stone, paper, or trash), pick them up when discovered, and encourage others to do the same.

  • Learn the basic classes of FOD, recognize its causes, and account for tools and hardware used during maintenance.

  • Look for loose objects discarded on the flight line during maintenance activities.

  • Periodically participate in “FOD walks” on taxiways and runways.

Explanation

Question 21 of 73

1

You need to find all of the TOs for a specific weapon system or piece of equipment. What type of index should you use?

Select one of the following:

  • TO catalog

  • Alphabetical index

  • Cross-reference table

  • LOAPs

Explanation

Question 22 of 73

1

You need to find the part number for an item prior to ordering it from supply. You’ve obtained the appropriate IPB manual for the end-item. What section of the IPB should you use to find the major assembly to which the desired item belongs?

Select one of the following:

  • Table of Contents

  • Reference designator index

  • Appropriate figure/illustration

  • National stock number and reference number index

Explanation

Question 23 of 73

1

Which TCTO is issued to correct unsafe conditions that, if not corrected, could result in serious or fatal injury to personnel?

Select one of the following:

  • Saftey

  • Urgent Action

  • Routine Action

  • Immediate Action

Explanation

Question 24 of 73

1

What type of TCTO is often accomplished by contractors, modification centers, or specific Air Force activities higher than organizational\intermediate-level maintenance due to the complexity involved?

Select one of the following:

  • Abbreviated TCTO.

  • Inspection TCTO.

  • Record TCTO.

  • Interim TCTO.

Explanation

Question 25 of 73

1

The main advantage of using abbreviated TOs is they

Select one of the following:

  • Cover safety in more detail

  • Serve as supplemental material

  • Paraphrase and eliminate the need for basic TOs

  • Organize and simplify instructions in a condensed version

Explanation

Question 26 of 73

1

Periodic inspection work cards are divided into three sections that cover the requirements for

Select one of the following:

  • Periodic inspections, lubrication, and special inspections.

  • Periodic inspections, special inspections, and safety.

  • Periodic inspections, lubrication, and safety.

  • Special inspections, lubrication, and safety.

Explanation

Question 27 of 73

1

Which abbreviated TO provides guidance for checking the general serviceability of a piece of equipment including applicable safety warnings, cautions, and notes?

Select one of the following:

  • Lubrication charts

  • Illustrated parts breakdown

  • Service inspection work cards

  • Periodic inspection work cards

Explanation

Question 28 of 73

1

An example of a TO deficiency is

Select one of the following:

  • Improper sequencing of pages

  • Insufficient information

  • Typographical errors

  • Misspelled words

Explanation

Question 29 of 73

1

Which form should you submit to correct a TO deficiency?

Select one of the following:

  • AFTO Form 1000, Deficiency Report.

  • AFTO Form 601A, Change Recommendation

  • AFTO Form 95, Support Equipment Record

  • AFTO Form 22, Technical Manual ™ Change Recommendation and Reply

Explanation

Question 30 of 73

1

What are the two general classes of Air Force publications?

Select one of the following:

  • Pamphlets and manuals

  • Departmental and field

  • Instructions and manuals

  • Supplements and instructions

Explanation

Question 31 of 73

1

OIs are similar to Air Force instructions, but they apply only to

Select one of the following:

  • Air Force wings

  • Support personnel

  • Maintenance personnel

  • Personnel within the issuing organization

Explanation

Question 32 of 73

1

What type of standard publication is used by lower headquarters to implement, amplify, interpret, or clarify a higher level publication?

Select one of the following:

  • Supplements

  • Visual aids

  • Bulletins

  • Manuals

Explanation

Question 33 of 73

1

The first number of a standard Air Force publication number is referred to as the “series” and represents the

Select one of the following:

  • Broad area covered

  • Specific area covered

  • Specific title of the publication

  • Specific military personnel affected

Explanation

Question 34 of 73

1

Where do you access standard Air Force publications?

Select one of the following:

  • Air Force e-Publishing website.

  • LOAPs

  • Base-level functional publication library

  • AFI 33–360

Explanation

Question 35 of 73

1

What impact is made on the maintenance organization by ensuring availability of adequate parts, equipment, and training?

Select one of the following:

  • Increasing bottlenecks and maximizing repair cycle time

  • Increasing bottlenecks and minimizing repair cycle time

  • Eliminating bottlenecks and minimizing repair cycle time

  • Eliminating bottlenecks and maximizing repair cycle time

Explanation

Question 36 of 73

1

Which maintenance levels are considered together as “field maintenance”?

Select one of the following:

  • Centralized and depot

  • Depot and provisional

  • Provisional and centralized

  • Organizational and intermediate

Explanation

Question 37 of 73

1

Organizational maintenance consists of

Select one of the following:

  • On-equipment tasks normally performed using the resources of an operating command at an operating location.

  • On-equipment tasks normally performed using the resources of a supporting command or intermediate repair facility.

  • Off-equipment tasks normally performed using the resources of an operating command at an operating location or intermediate repair facility.

  • On- or off-equipment tasks that require highly specialized skills, sophisticated shop equipment, and/or special facilities of a supporting command

Explanation

Question 38 of 73

1

The main purpose of the inspection system is to

Select one of the following:

  • Get ahead on unscheduled maintenance

  • Keep equipment operating and looking good

  • Keeping the mechanic working on minor problems

  • Locate problems and repair equipment before total failure

Explanation

Question 39 of 73

1

The maintenance symbol the represents the most serious operational condition for equipment is a

Select one of the following:

  • Rex X

  • Red Dash

  • Red Diagonal

  • Circled Red X

Explanation

Question 40 of 73

1

Which symbol indicates an operational check is overdue?

Select one of the following:

  • Red X

  • Red Dash

  • Red Diagonal

  • Circled Red X

Explanation

Question 41 of 73

1

Which section of the AFTO Form 244 is used to record a forms review?

Select one of the following:

  • Part II, Non-scheduled Inspection

  • Part III, Scheduled Inspection

  • Part IV, Supervisory Review

  • Part V, Maintenance/Delayed Discrepancy

Explanation

Question 42 of 73

1

When closing out an AFTO Form 244, what is entered on the form to close out uncompleted inspections?

Select one of the following:

  • A red X and your initials in Part IV, Supervisory Review

  • A red X and your initials in Part III, Scheduled Inspections

  • The letters “CF” (for carried forward) and your initials in Part IV, Supervisory Review

  • The letters “CF” (for carried forward) and your initials in Part III, Scheduled Inspections

Explanation

Question 43 of 73

1

What is the condition of a component bearing a green equipment condition label?

Select one of the following:

  • Unserviceable (Condemned)

  • Unserviceable (Repairable)

  • Serviceable

  • Suspended

Explanation

Question 44 of 73

1

What color is the equipment condition tag attached to an item being held as an exhibit?

Select one of the following:

  • Brown

  • Green

  • White

  • Yellow

Explanation

Question 45 of 73

1

What maintenance supply form is used to order commonly stocked supplies or turn in excess or unserviceable property?

Select one of the following:

  • AF Form 2005

  • AFTO Form 350

  • DD Form 1348-6

  • DD Form 1348-1A

Explanation

Question 46 of 73

1

What MDD code identifies the system that was worked on?

Select one of the following:

  • Type maintenance

  • Work unit code

  • Category of labor

  • Units

Explanation

Question 47 of 73

1

Distinguish between “excess” and “surplus” as they apply to Air Force supply discipline.

Select one of the following:

  • Excess and surplus are the same.

  • Excess and surplus are the turn-in of property no longer needed.

  • Surplus is property no longer needed at your base, and excess is property no longer needed by another military service or Federal agency.

  • Excess is property no longer needed at your base, and surplus is property no longer needed by another military service or Federal agency.

Explanation

Question 48 of 73

1

What is a major concept regarding “economic use” of supplies and equipment?

Select one of the following:

  • Use them only for their intended purposes.

  • Always order the least expensive item to do the job.

  • Protect items from hazards such as fire or corrosion.

  • Order only the minimum supplies necessary to do a job.

Explanation

Question 49 of 73

1

Who is responsible for ensuring that property records of supply transactions are kept accurately?

Select one of the following:

  • Commander

  • Supervisor

  • Person who signed for an account

  • Person who has possession of the property

Explanation

Question 50 of 73

1

To be held responsible for property, you must

Select one of the following:

  • Possess it

  • Sign for it

  • Be a 5 level

  • Be a supervisor

Explanation

Question 51 of 73

1

What are you required to do with Air Force property you might find and believe it to be lost or misplaced?

Select one of the following:

  • Leave it where you found it

  • Place it back into the supply system.

  • Take the item to the organizational commander.

  • Take it to the security forces lost and found section.

Explanation

Question 52 of 73

1

What equipment does not require an AFTO Form 375?

Select one of the following:

  • Items less than $2,500

  • Items less than $25,000

  • Items more than $2,500

  • Items more than $25,000

Explanation

Question 53 of 73

1

Items that retain their identity throughout the period of their use and may be turned in and reissued for use by others are considered

Select one of the following:

  • DIFM

  • Excess

  • Expendable

  • Nonexpendable

Explanation

Question 54 of 73

1

When the bench stock quantity level falls below 50 % for an item, you should

Select one of the following:

  • Post a due-out list

  • Place a red tag on the bin

  • Notify supply that stock level is low

  • Initial the initial supply stock listing

Explanation

Question 55 of 73

1

The responsibility of a person to make good any loss, destruction, or damage of government property caused by misuse or neglect is what kind of liability?

Select one of the following:

  • Property

  • Personal

  • Pecuniary

  • Command

Explanation

Question 56 of 73

1

How can a person be relieved from property responsibility other than by pecuniary liability?

Select one of the following:

  • Turn-in only

  • Transfer only

  • Turn-in or Transfer

  • Cash collection voucher or statement of charges

Explanation

Question 57 of 73

1

A statement of charges would be prepared under which of these circumstances?

Select one of the following:

  • If a lost item is not expendable

  • If you make a cash payment for a lost item

  • If you signed a hand receipt for a lost item

  • If you want to use payroll deduction to pay the cost of a lost item

Explanation

Question 58 of 73

1

What must be done if SSgt Ortiz refuses to admit pecuniary liability for the loss of a $275 lawn mower for which he has custodial responsibility?

Select one of the following:

  • A report of survey must be initiated.

  • A statement of charges must be prepared.

  • Charges must be made on a military pay order.

  • The mower must be replaced by one of equivalent value.

Explanation

Question 59 of 73

1

After a deficiency has been discovered, when must a category II PQDR be submitted to the screening point?

Select one of the following:

  • 24 hours

  • 2 calendar days

  • 5 calendar days

  • 10 calendar days

Explanation

Question 60 of 73

1

Within the deficiency reporting system, who is responsible for the resolution of the deficiency?

Select one of the following:

  • Originating point

  • Screening point

  • Action point

  • Support point

Explanation

Question 61 of 73

1

Within the deficiency reporting system, who assigns a report control number and ensures proper marking and handling of exhibits?

Select one of the following:

  • Originating point

  • Screening point

  • Action point

  • Support point

Explanation

Question 62 of 73

1

Who should AGE maintainers contact for submittal format of agenda items when preparing for the PIWG?

Select one of the following:

  • MAJCOM AGE functional managers

  • Screening point within the originating activity

  • Lead command (AFMC)

  • WR-ALC

Explanation

Question 63 of 73

1

On which type of metal can you leave corrosion as long as the component is operational?

Select one of the following:

  • Steel

  • Copper

  • Aluminum

  • None, all corrosion must be removed.

Explanation

Question 64 of 73

1

What marking is applied to AGE for night safety?

Select one of the following:

  • Informational

  • Safety/Danger

  • Reflectorization

  • Caution/Warning

Explanation

Question 65 of 73

1

Guidelines for storing AGE are in

Select one of the following:

  • TO 35-1-3

  • TO 35-1-4

  • TO 35-1-12

  • AFMAN 23-110

Explanation

Question 66 of 73

1

Which of these items must be removed from test equipment before storage?

Select one of the following:

  • Wet and dry cell batteries

  • Dry charge batteries

  • Battery compartment

  • Battery holder

Explanation

Question 67 of 73

1

What AGE must have the fuel drained when preparing it for mobility?

Select one of the following:

  • Equipment with fuel levels that cannot be verified

  • Self-propelled equipment required for immediate use at deployment sites

  • Equipment that is not self-propelled and is required for immediate use at deployment sites

  • All AGE must have fuel drained prior to deployment; there are no exceptions

Explanation

Question 68 of 73

1

During a battery condition check, what is an acceptable voltage reading for a 12-volt battery?

Select one of the following:

  • 8–2 volts

  • 10–12 volts

  • 12.4 volts or lower

  • 12.7 volts or higher

Explanation

Question 69 of 73

1

After connecting a voltmeter across the starter terminals and clamping a current probe around the positive battery cable, what must be done prior to cranking the engine when performing a starting system check on AGE?

Select one of the following:

  • Estimate the temperature of the battery.

  • Prevent the engine from starting.

  • Perform a battery cable test.

  • Disconnect the voltmeter.

Explanation

Question 70 of 73

1

How should you approach a parked aircraft with your vehicle?

Select one of the following:

  • Only when a guide is posted.

  • Within 25 feet of an aircraft with engines running

  • With the driver’s side of the vehicle toward the aircraft

  • With the driver’s side of the vehicle away from the aircraft

Explanation

Question 71 of 73

1

What should you do if your vehicle meets a moving aircraft at night?

Select one of the following:

  • Turn off your headlights and leave your parking lights on.

  • Dim your headlights and continue on.

  • Stop and change directions.

  • Turn all lights off.

Explanation

Question 72 of 73

1

Why should you apply silicone sealant to the valve stem area of a wheel?

Select one of the following:

  • To keep rims from flying apart

  • To keep water from entering rims

  • As a treatment for weather cracks

  • As a treatment for severe corrosion

Explanation

Question 73 of 73

1

What must you do before inflating the inner tube fully on a split rim tire?

Select one of the following:

  • Fully deflate the tire

  • Torque wheel lug bolts

  • Check tires for foreign objects

  • Ensure rims are completely bolted together and torqued.

Explanation

Previous
Check answer
Next