CCNA Part 1

Por favor, aguarde! Carregando...

Questão 1 de 117

Which layer of the OSI reference Model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?

Selecione uma das seguintes:

Transport
Network
Presentation
Session
Application

Explicação

Questão 2 de 117

Which of the following describes the roles of devices in a WAN? (Choose 3)

Selecione uma ou mais das seguintes:

A CSU/DSU terminates a digital local loop.
A modem terminates a digital loop.
A CSU/DSU terminates an analog local loop
A modem terminates an analog local loop
A router is commonly considered a DTE device.
A router is commonly considered a DCE device.

Explicação

Questão 3 de 117

A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation?

Selecione uma das seguintes:

Application
Presentation
Session
Transport
Internet
Data-Link

Explicação

Questão 4 de 117

A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?

Selecione uma das seguintes:

This is a 10 Mb/s switch port.
This is a 100 Mb/s switch port.
This is an Ethernet port operating at half duplex.
This is an Ethernet port operating at full duplex.
This is a port on a network interface card in a PC.

Explicação

Questão 5 de 117

A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?

Selecione uma das seguintes:

Session
Transport
Network
Data-Link
Physical

Explicação

Questão 6 de 117

Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.)

Selecione uma ou mais das seguintes:

The transport layer divides a data stream into segments and may add reliability and flow control information.
The data link layer adds physical source and destination addresses and an FCS to the segment.
Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information.
Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
The presentation layer translates bits into voltages for transmission across the physical link.

Explicação

Questão 7 de 117

Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.)

Selecione uma ou mais das seguintes:

Spanning Tree Protocol allows switches to automatically share VLAN information.
Establishing VLANs increases the number of broadcast domains.
Switches that are configured with VLANs make forwarding decisions based on both Layer 2 and Layer 3 address information.
Microsegmentation decreases the number of collisions on the network.
In a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port.
If a switch receives a frame for an unknown destination, it uses ARP to resolve the address.

Explicação

Questão 8 de 117

Where does routing occur within the DoD TCP/IP reference model?

Selecione uma das seguintes:

Application
Internet
Network
Transport

Explicação

Questão 9 de 117

For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)

Selecione uma ou mais das seguintes:

To uniquely identify devices at Layer 2
To allow communication with devices on a different network
To differentiate a Layer 2 frame from a Layer 3 packet
To establish a priority system to determine which device gets to transmit first
To allow communication between different devices on the same network
To allow detection of a remote device when its physical address is unknown

Explicação

Questão 10 de 117

In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)

Selecione uma ou mais das seguintes:

When they receive a special token
When there is a carrier
When they detect no other devices are sending
When the medium is idle
When the server grants access

Explicação

Questão 11 de 117

Which layer of the OSI reference Model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?

Selecione uma das seguintes:

Transport
Network
Presentation
Session
Application

Explicação

Questão 12 de 117

A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?

Selecione uma das seguintes:

Use a hub to connect the four VLANS with a Fast Ethernet interface on the router.
Add a second router to handle the VLAN traffic.
Add two more Fast Ethernet interfaces.
Implement a router-on-a-stick configuration.

Explicação

Questão 13 de 117

What is the difference between a CSU/DSU and a modem?

Selecione uma das seguintes:

A CSU/DSU converts analog signals from a router to a leased line; a modem converts analog signals from a router to a leased line.
A CSU/DSU converts analog signals from a router to a phone line; a modem converts digital signals from a router to a leased line.
A CSU/DSU converts digital signals from a router to a phone line; a modem converts analog signals from a router to a phone line.
A CSU/DSU converts digital signals from a router to a leased line; a modem converts digital signals from a router to a phone line.

Explicação

Questão 14 de 117

Which port state is introduced by Rapid-PVST?

Selecione uma das seguintes:

Learning
Listening
Discarding
Forwarding

Explicação

Questão 15 de 117

VLAN 3 is not yet configured on your switch. What happens if you set the switchport access VLAN 3 command in interface configuration mode?

Selecione uma das seguintes:

The command is rejected
The port turns amber
The command is accepted and the respective VLAN is added to vlan.dat.
The command is accepted and you must configure the VLAN manually.

Explicação

Questão 16 de 117

What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?

Selecione uma das seguintes:

Path Cost
Lowest port MAC address
VTP revision number
Highest port priority number
Port priority number and MAC address

Explicação

Questão 17 de 117

In a switched environment, what does the IEEE 802.1Q standard describe?

Selecione uma das seguintes:

The operation of VTP
A method of VLAN trunking
An approach to wireless LAN communication
The process of root bridge selection
VLAN pruning

Explicação

Questão 18 de 117

What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?

Selecione uma das seguintes:

It creates a VLAN 999 interface.
It designates VLAN 999 for untagged traffic.
It blocks VLAN 999 traffic from passing on the trunk.
It designates VLAN 999 as the default for all unknown tagged traffic.

Explicação

Questão 19 de 117

Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)

Selecione uma ou mais das seguintes:

802.1d
VTP
802.1q
STP
SAP

Explicação

Questão 20 de 117

Which switch would STP choose to become the root bridge in the selection process?

Selecione uma das seguintes:

32768: 11-22-33-44-55-66
32768: 22-33-44-55-66-77
32769: 11-22-33-44-55-65
32769: 22-33-44-55-66-78

Explicação

Questão 21 de 117

A switch is configured with all ports assigned to VLAN 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?

Selecione uma das seguintes:

More collision domains will be created.
IP address utilization will be more efficient.
More bandwidth will be required than was needed previously.
An additional broadcast domain will be created.

Explicação

Questão 22 de 117

What are three benefits of implementing VLANs? (Choose three.)

Selecione uma ou mais das seguintes:

A higher level of network security can be reached by separating sensitive data traffic from other network traffic.
A more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure.
A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure.
Broadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing their size.
Broadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing their size.
VLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to the same broadcast domain.
Port-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks.

Explicação

Questão 23 de 117

Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?

Selecione uma das seguintes:

802.3ad
802.1w
802.1D
802.1Q

Explicação

Questão 24 de 117

Which of the following are benefits of VLANs? (Choose three.)

Selecione uma ou mais das seguintes:

They increase the size of collision domains.
They allow logical grouping of users by function.
They can enhance network security.
They increase the size of broadcast domains while decreasing the number of collision domains.
They increase the number of broadcast domains while decreasing the size of the broadcast domains.
They simplify switch administration.

Explicação

Questão 25 de 117

Which two states are the port states when RSTP has converged? (Choose two.)

Selecione uma ou mais das seguintes:

Discarding
Listening
Learning
Forwarding
Disabled

Explicação

Questão 26 de 117

Which two commands can be used to verify a trunk link configuration status on a given Cisco switch interface? (Choose two.)

Selecione uma ou mais das seguintes:

Show interface trunk
Show interface interface
Show ip interface brief
Show interface vlan
show interface switchport

Explicação

Questão 27 de 117

Which command enables RSTP on a switch?

Selecione uma das seguintes:

spanning-tree uplinkfast
spanning-tree mode rapid-pvst
spanning-tree backbonefast
spanning-tree mode mst

Explicação

Questão 28 de 117

Why will a switch never learn a broadcast address?

Selecione uma das seguintes:

Broadcasts only use network layer addressing.
A broadcast frame is never forwarded by a switch.
A broadcast address will never be the source address of a frame.
Broadcast addresses use an incorrect format for the switching table.
Broadcast frames are never sent to switches.

Explicação

Questão 29 de 117

Which two link protocols are used to carry multiple VLANs over a single link? (Choose two.)

Selecione uma ou mais das seguintes:

VTP
802.1q
IGP
ISL
802.3u

Explicação

Questão 30 de 117

Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?

Selecione uma das seguintes:

1 through 1001
2 through 1001
1 through 1002
2 through 1005

Explicação

Questão 31 de 117

Which statement about VLAN operation on Cisco Catalyst switches is true?

Selecione uma das seguintes:

When a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table.
Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN.
Broadcast and multicast frames are retransmitted to ports that are configured on different VLAN.
Ports between switches should be configured in access mode so that VLANs can span across the ports.

Explicação

Questão 32 de 117

Which three statements about RSTP are true? (Choose three.)

Selecione uma ou mais das seguintes:

RSTP significantly reduces topology reconverging time after a link failure.
RSTP expands the STP port roles by adding the alternate and backup roles.
RSTP port states are blocking, discarding, learning, or forwarding.
RSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
RSTP also uses the STP proposal-agreement sequence.
RSTP uses the same timer-based process as STP on point-to-point links.

Explicação

Questão 33 de 117

At which layer of the OSI model is RSTP used to prevent loops?

Selecione uma das seguintes:

Physical
Data Link
Network
Transport

Explicação

Questão 34 de 117

What does a Layer 2 switch use to decide where to forward a received frame?

Selecione uma das seguintes:

source MAC address
source IP address
source switch port
destination IP address
destination port address
destination MAC address

Explicação

Questão 35 de 117

Which two benefits are provided by creating VLANs? (Choose two.)

Selecione uma ou mais das seguintes:

added security
dedicated bandwidth
provides segmentation
allows switches to route traffic between subinterfaces
contains collisions

Explicação

Questão 36 de 117

Which command can be used from a PC to verify the connectivity between hosts that connect through a switch in the same LAN?

Selecione uma das seguintes:

Ping address
Tracert address
Traceroute address
ARP address

Explicação

Questão 37 de 117

Which two of these are characteristics of the 802.1Q protocol? (Choose two.)

Selecione uma ou mais das seguintes:

It is used exclusively for tagging VLAN frames and does not address network reconvergence following switched network topology changes.
It modifies the 802.3 frame header, and thus requires that the FCS be recomputed.
It is a Layer 2 messaging protocol which maintains VLAN configurations across networks.
It includes an 8-bit field which specifies the priority of a frame.
It is a trunking protocol capable of carrying untagged frames.

Explicação

Questão 38 de 117

What is one benefit of PVST+?

Selecione uma das seguintes:

PVST+ supports Layer 3 load balancing without loops.
PVST+ reduces the CPU cycles for all the switches in the network.
PVST+ allows the root switch location to be optimized per VLAN.
PVST+ automatically selects the root bridge location, to provide optimized bandwidth usage.

Explicação

Questão 39 de 117

Which are valid modes for a switch port used as a VLAN trunk? (Choose three.)

Selecione uma ou mais das seguintes:

Transparent
Auto
On
Desirable
Blocking
Forwarding

Explicação

Questão 40 de 117

Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

Selecione uma ou mais das seguintes:

802.1Q native VLAN frames are untagged by default.
802.1Q trunking ports can also be secure ports.
802.1Q trunks can use 10 Mb/s Ethernet interfaces.
802.1Q trunks require full-duplex, point-to-point connectivity.
802.1Q trunks should have native VLANs that are the same at both ends.

Explicação

Questão 41 de 117

Which term describes a spanning-tree network that has all switch ports in either the blocking or fowarding state?

Selecione uma das seguintes:

Converged
Redundant
Provisioned
Spanned

Explicação

Questão 42 de 117

What are the possible trunking modes for a switch port? (Choose three.)

Selecione uma ou mais das seguintes:

Transparent
Auto
On
Desireable
Client
Forwarding

Explicação

Questão 43 de 117

Which two of these statements regarding RSTP are correct? (Choose two.)

Selecione uma ou mais das seguintes:

RSTP cannot operate with PVST+.
RSTP defines new port roles.
RSTP defines no new port states.
RSTP is a proprietary implementation of IEEE 802.1D STP.
RSTP is compatible with the original IEEE 802.1D STP.

Explicação

Questão 44 de 117

Three switches are connected to one another via trunk ports. Assuming the default switch configuration, which switch is elected as the root bridge for the spanning-tree instance of VLAN 1?

Selecione uma das seguintes:

The switch with the highest MAC address
The switch with the lowest MAC address
The switch with the highest IP address
The switch with the lowest IP address

Explicação

Questão 45 de 117

What are three advantages of VLANs (Choose Three)

Selecione uma ou mais das seguintes:

VLANs establish broadcast domains in switched networks.
VLANs utilize packet filtering to enhance network security.
VLANs provide a method of conserving IP addresses in large networks.
VLANs provide a low-latency internetworking alternative to routed networks.
VLANs allow access to network services based on department, not physical location.
VLANs can greatly simplify adding, moving, or changing hosts on the network.

Explicação

Questão 46 de 117

Cisco Catalyst switches CAT1 and CAT2 have a connection between them using ports FA0/13. An 802.1Q trunk is configured between the two switches. On CAT1, VLAN 10 is chosen as native, but on CAT2 the native VLAN is not specified.
What will happen in this scenario?

Selecione uma das seguintes:

802.1Q giants frames could saturate the link.
VLAN 10 on CAT1 and VLAN 1 on CAT2 will send untagged frames.
A native VLAN mismatch error message will appear.
VLAN 10 on CAT1 and VLAN 1 on CAT2 will send tagged frames.

Explicação

Questão 47 de 117

You have been asked to come up with a subnet mask that will allow all three web servers to be on the same network while providing the maximum number of subnets. Which network address and subnet mask meet this requirement?

Selecione uma das seguintes:

192.168.252.0 255.255.255.252
192.168.252.8 255.255.255.248
192.168.252.8 255.255.255.252
192.168.252.16 255.255.255.240
192.168.252.16 255.255.255.252

Explicação

Questão 48 de 117

Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network address?

Selecione uma das seguintes:

172.16.16.0
172.16.0.0
172.16.24.0
172.16.28.0

Explicação

Questão 49 de 117

Which IPv6 address is the equivalent of the IPv4 interface loopback address 127.0.0.1?

Selecione uma das seguintes:

::1
::
2000::/3
0::/10

Explicação

Questão 50 de 117

You are working in a data center environment and are assigned the address range 10.188.31.0/23. You are asked to develop an IP addressing plan to allow the maximum number of subnets with as many as 30 hosts each. Which IP address range meets these requirements?

Selecione uma das seguintes:

10.188.31.0/26
10.188.31.0/25
10.188.31.0/28
10.188.31.0/27
10.188.31.0/29

Explicação

Questão 51 de 117

What are three features of the IPv6 protocol? (Choose three.)

Selecione uma ou mais das seguintes:

Optional IPsec
Autoconfiguration
No broadcasts
Complicated header
Plug-and-play
Checksum

Explicação

Questão 52 de 117

Which command enables IPv6 forwarding on a Cisco router?

Selecione uma das seguintes:

IPv6 local
IPv6 host
IPv6 unicast-routing
IPv6 neighbor

Explicação

Questão 53 de 117

What is known as "one-to-nearest" addressing in IPv6?

Selecione uma das seguintes:

Global Unicast
Anycast
Multicast
Unspecified address

Explicação

Questão 54 de 117

What is the first 24 bits in a MAC address called?

Selecione uma das seguintes:

Explicação

Questão 55 de 117

Which subnet mask will place all hosts on Network B in the same subnet with the least amount of wasted addresses?

Selecione uma das seguintes:

255.255.255.0
255.255.254.0
255.255.252.0
255.255.248.0

Explicação

Questão 56 de 117

What is the most appropriate summarization for these routes?

Selecione uma das seguintes:

10.0.0.0/21
10.0.0.0/22
10.0.0.0/23
10.0.0.0/24

Explicação

Questão 57 de 117

Which two are features of IPv6? (Choose two.)

Selecione uma ou mais das seguintes:

Anycast
Broadcast
Multicast
Podcast
Allcast

Explicação

Questão 58 de 117

Which two of these statements are true of IPv6 address representation? (Choose two.)

Selecione uma ou mais das seguintes:

There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
A single interface may be assigned multiple IPv6 addresses of any type.
Every IPv6 interface contains at least one loopback address.
The first 64 bits represent the dynamically created interface ID.
Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.

Explicação

Questão 59 de 117

A new subnet with 60 hosts has been added to the network. Which subnet address should this network use to provide enough usable addresses while wasting the fewest addresses?

Selecione uma das seguintes:

192.168.1.56/26
192.168.1.56/27
192.168.1.64/26
192.168.1.64/27

Explicação

Questão 60 de 117

The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?

Selecione uma das seguintes:

Explicação

Questão 61 de 117

What will happen if a private IP address is assigned to a public interface connected to an ISP?

Selecione uma das seguintes:

Addresses in a private range will be not be routed on the Internet backbone.
Only the ISP router will have the capability to access the public network.
The NAT process will be used to translate this address to a valid IP address.
A conflict of IP addresses happens, because other public routers can use the same range.

Explicação

Questão 62 de 117

Which two benefits are provided by using a hierarchical addressing network addressing scheme?
(Choose two.)

Selecione uma ou mais das seguintes:

Reduces routing table entries
Auto-negotiation of media rates
Efficient utilization of MAC addresses
Dedicated communications between devices
Ease of management and troubleshooting

Explicação

Questão 63 de 117

What is the alternative notation for the IPv6 address
B514:82C3:0000:0000:0029:EC7A:0000:EC72?

Selecione uma das seguintes:

B514 : 82C3 : 0029 : EC7A : EC72
B514 : 82C3 :: 0029 : EC7A : EC72
B514 : 82C3 : 0029 :: EC7A : 0000 : EC72
B514 : 82C3 :: 0029 : EC7A : 0 : EC72

Explicação

Questão 64 de 117

All hosts have connectivity with one another. Which statements describe the addressing scheme that is in use in the network? (Choose three.)

Selecione uma ou mais das seguintes:

The subnet mask in use is 255.255.255.192.
The subnet mask in use is 255.255.255.128.
The IP address 172.16.1.25 can be assigned to hosts in VLAN1
The IP address 172.16.1.205 can be assigned to hosts in VLAN1
The LAN interface of the router is configured with one IP address.
The LAN interface of the router is configured with multiple IP addresses.

Explicação

Questão 65 de 117

Which two statements describe characteristics of IPv6 unicast addressing? (Choose two.)

Selecione uma ou mais das seguintes:

Global addresses start with 2000::/3.
Link-local addresses start with FE00:/12.
Link-local addresses start with FF00::/10.
There is only one loopback address and it is ::1.
If a global address is assigned to an interface, then that is the only allowable address for the
interface.

Explicação

Questão 66 de 117

The network administrator has been asked to give reasons for moving from IPv4 to IPv6. What are
two valid reasons for adopting IPv6 over IPv4? (Choose two.)

Selecione uma ou mais das seguintes:

No broadcast
Change of source address in the IPv6 header
Change of destination address in the IPv6 header
Telnet access does not require a password
Autoconfiguration
NAT

Explicação

Questão 67 de 117

An administrator must assign static IP addresses to the servers in a network. For network
192.168.20.24/29, the router is assigned the first usable host address while the sales server is
given the last usable host address. Which of the following should be entered into the IP properties
box for the sales server?

Selecione uma das seguintes:

IP address: 192.168.20.14
Subnet Mask: 255.255.255.248
Default Gateway: 192.168.20.9
IP address: 192.168.20.254
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.20.1
IP address: 192.168.20.30
Subnet Mask: 255.255.255.248
Default Gateway: 192.168.20.25
IP address: 192.168.20.30
Subnet Mask: 255.255.255.240
Default Gateway: 192.168.20.17
IP address: 192.168.20.30
Subnet Mask: 255.255.255.240
Default Gateway: 192.168.20.25

Explicação

Questão 68 de 117

Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each LAN containing 5 to 26 hosts?

Selecione uma das seguintes:

0.0.0.240
255.255.255.252
255.255.255.0
255.255.255.224
255.255.255.240

Explicação

Questão 69 de 117

How many bits are contained in each field of an IPv6 address?

Selecione uma das seguintes:

Explicação

Questão 70 de 117

What are three approaches that are used when migrating from an IPv4 addressing scheme to an
IPv6 scheme. (Choose three.)

Selecione uma ou mais das seguintes:

Enable dual-stack routing
Configure IPv6 directly
Configure IPv4 tunnels between IPv6 islands
Use proxying and translation to translate IPv6 packets into IPv4 packets
Statically map IPv4 addresses to IPv6 addresses
Use DHCPv6 to map IPv4 addresses to IPv6 addresses

Explicação

Questão 71 de 117

How is an EUI-64 format interface ID created from a 48-bit MAC address?

Selecione uma das seguintes:

By appending 0xFF to the MAC address
By prefixing the MAC address with 0xFFEE
By prefixing the MAC address with 0xFF and appending 0xFF to it
By inserting 0xFFFE between the upper three bytes and the lower three bytes of the MAC address
By prefixing the MAC address with 0xF and inserting 0xF after each of its first three bytes

Explicação

Questão 72 de 117

Which three are characteristics of an IPv6 anycast address? (Choose three.)

Selecione uma das seguintes:

One-to-many communication model
One-to-nearest communication model
Any-to-many communication model
A unique IPv6 address for each device in the group
The same address for multiple devices in the group
Delivery of packets to the group interface that is closest to the sending device

Explicação

Questão 73 de 117

Which option is a valid IPv6 address?

Selecione uma das seguintes:

2001:0000:130F::099a::12a
2002:7654:A1AD:61:81AF:CCC1
FEC0:ABCD:WXYZ:0067::2A4
2004:1:25A4:886F::1

Explicação

Questão 74 de 117

A national retail chain needs to design an IP addressing scheme to support a nationwide network. The company needs a minimum of 300 sub-networks and a maximum of 50 host addresses per subnet. Working with only one Class B address, which of the following subnet masks will support an appropriate addressing scheme? (Choose two.)

Selecione uma ou mais das seguintes:

255.255.255.0
255.255.255.128
255.255.252.0
255.255.255.224
255.255.255.192
255.255.248.0

Explicação

Questão 75 de 117

Which IPv6 address is the all-router multicast group?

Selecione uma das seguintes:

FF02::1
FF02::2
FF02::3
FF02::4

Explicação

Questão 76 de 117

Which IPv6 address is valid?

Selecione uma das seguintes:

2001:0db8:0000:130F:0000:0000:08GC:140B
2001:0db8:0:130H::87C:140B
2031::130F::9C0:876A:130B
2031:0:130F::9C0:876A:130B

Explicação

Questão 77 de 117

Which command can you use to manually assign a static IPv6 address to a router interface?

Selecione uma das seguintes:

ipv6 autoconfig 2001:db8:2222:7272::72/64
ipv6 address 2001:db8:2222:7272::72/64
ipv6 address PREFIX_1 ::1/64
ipv6 autoconfig

Explicação

Questão 78 de 117

Which of these represents an IPv6 link-local address?

Selecione uma das seguintes:

FE80::380e:611a:e14f:3d69
FE81::280f:512b:e14f:3d69
FEFE:0345:5f1b::e14d:3d69
FE08::280e:611:a:f14f:3d69

Explicação

Questão 79 de 117

The network administrator is asked to configure 113 point-to-point links. Which IP addressing scheme defines the address range and subnet mask that meet the requirement and waste the fewest subnet and host addresses?

Selecione uma das seguintes:

10.10.0.0/16 subnetted with mask 255.255.255.252
10.10.0.0/18 subnetted with mask 255.255.255.252
10.10.1.0/24 subnetted with mask 255.255.255.252
10.10.0.0/23 subnetted with mask 255.255.255.252
10.10.1.0/25 subnetted with mask 255.255.255.252

Explicação

Questão 80 de 117

What will Router1 do when it receives the data frame shown? (Choose three.)

Selecione uma ou mais das seguintes:

Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965.
Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1.
Router1 will strip off the destination MAC address and replace it with the MAC address 0000.0c07.4320.
Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1.
Router1 will forward the data packet out interface FastEthernet0/1.
Router1 will forward the data packet out interface FastEthernet0/2.

Explicação

Questão 81 de 117

Which three statements correctly describe Network Device A? (Choose three.)

Selecione uma ou mais das seguintes:

With a network wide mask of 255.255.255.128, each interface does not require an IP address.
With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.
With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.
With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.
With a network wide mask of 255.255.254.0, each interface does not require an IP address.

Explicação

Questão 82 de 117

Host A pings interface S0/0 on router 3. What is the TTL value for that ping?

Selecione uma das seguintes:

Explicação

Questão 83 de 117

After HostA pings HostB, which entry will be in the ARP cache of HostA to support this transmission?

Selecione uma das seguintes:

Explicação

Questão 84 de 117

Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server?

Selecione uma das seguintes:

The MAC address of router interface e0
The MAC address of router interface e1
The MAC address of the server network interface
The MAC address of host A

Explicação

Questão 85 de 117

What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)

Selecione uma ou mais das seguintes:

The number of collision domains would remain the same.
The number of collision domains would decrease.
The number of collision domains would increase.
The number of broadcast domains would remain the same.
The number of broadcast domains would decrease.
The number of broadcast domains would increase.

Explicação

Questão 86 de 117

Which destination addresses will be used by Host A to send data to Host C? (Choose two.)

Selecione uma ou mais das seguintes:

The IP address of Switch 1
The MAC address of Switch 1
The IP address of Host C
The MAC address of Host C
The IP address of the router's E0 interface
The MAC address of the router's E0 interface

Explicação

Questão 87 de 117

Based on the information given, which switch will be elected root bridge and why?

Selecione uma ou mais das seguintes:

Switch A, because it has the lowest MAC address
Switch A, because it is the most centrally located switch
Switch B, because it has the highest MAC address
Switch C, because it is the most centrally located switch
Switch C, because it has the lowest priority
Switch D, because it has the highest priority

Explicação

Questão 88 de 117

Which of the following statements describe the network shown in the graphic? (Choose two.)

Selecione uma ou mais das seguintes:

There are two broadcast domains in the network.
There are four broadcast domains in the network.
There are six broadcast domains in the network.
There are four collision domains in the network.
There are five collision domains in the network.
There are seven collision domains in the network.

Explicação

Questão 89 de 117

Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down.

Selecione uma ou mais das seguintes:

Router C will use ICMP to inform Host 1 that Host 2 cannot be reached.
Router C will use ICMP to inform Router B that Host 2 cannot be reached.
Router C will use ICMP to inform Host 1, Router A, and Router B that Host 2 cannot be reached.
Router C will send a Destination Unreachable message type.
Router C will send a Router Selection message type.
Router C will send a Source Quench message type.

Explicação

Questão 90 de 117

Refer to the exhibit
Switch port FastEthernet 0/24 on ALSwitch1 will be used to create an IEEE 802.1Q-compliant trunk to another switch. Based on the output shown, what is the reason the trunk does not form, even though the proper cabling has been attached?.

Selecione uma das seguintes:

VLANs have not been created yet.
An IP address must be configured for the port.
The port is currently configured for access mode.
The correct encapsulation type has not been configured.
The “no shutdown” command has not been entered for the port.

Explicação

Questão 91 de 117

Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data?

Selecione uma das seguintes:

Switch-1 will drop the data because it does not have an entry for that MAC address.
Switch-1 will flood the data out all of its ports except the port from which the data originated.
Switch-1 will send an ARP request out all its ports except the port from which the data originated.
Switch-1 will forward the data to its default gateway.

Explicação

Questão 92 de 117

A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands is required to
accomplish this task?

Selecione uma das seguintes:

SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0
SwitchB(config-if)# no shutdown
SwitchB(config)# ip default-gateway 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
SwitchB(config)# ip default-network 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
SwitchB(config)# ip route 192.168.8.254 255.255.255.0
SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown

Explicação

Questão 93 de 117

All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?

Selecione uma das seguintes:

The access link needs to be configured in multiple VLANs.
The link between the switches is configured in the wrong VLAN.
The link between the switches needs to be configured as a trunk.
VTP is not configured to carry VLAN information between the switches.
Switch IP addresses must be configured in order for traffic to be forwarded between the switches.

Explicação

Questão 94 de 117

Which WAN protocol is being used?

Selecione uma das seguintes:

ATM
HDLC
Frame Relay
PPP

Explicação

Questão 95 de 117

Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?

Selecione uma das seguintes:

This switch has more than one interface connected to the root network segment in VLAN 2.
This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
This switch interface has a higher path cost to the root bridge than another in the topology.
This switch has a lower bridge ID for VLAN 2 than the elected designated switch.

Explicação

Questão 96 de 117

Why has this switch not been elected the root bridge for VLAN1?

Selecione uma das seguintes:

It has more than one interface that is connected to the root network segment.
It is running RSTP while the elected root bridge is running 802.1d spanning tree.
It has a higher MAC address than the elected root bridge.
It has a higher bridge ID than the elected root bridge.

Explicação

Questão 97 de 117

Which ports will be STP designated ports if all the links are operating at the same bandwidth? (Choose three)

Selecione uma ou mais das seguintes:

Switch A - Fa0/0
Switch A - Fa0/1
Switch B - Fa0/0
Switch B - Fa0/1
Switch C - Fa0/0
Switch C - Fa0/1

Explicação

Questão 98 de 117

How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?

Selecione uma das seguintes:

The ports only need to be connected by a crossover cable.
SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode access
SwitchX(config-if)# switchport access vlan 1
SwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
SwitchX(config-if)# switchport trunk vlan 1
SwitchX(config-if)# switchport trunk vlan 10
SwitchX(config-if)# switchport trunk vlan 20

Explicação

Questão 99 de 117

A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 2.
What causes this behavior?

Selecione uma das seguintes:

Trunk mode mismatches
Allowing only VLAN 2 on the destination
Native VLAN mismatches
VLANs that do not correspond to a unique IP subnet

Explicação

Questão 100 de 117

Which statement is true?

Selecione uma das seguintes:

The Fa0/11 role confirms that SwitchA is the root bridge for VLAN 20.
VLAN 20 is running the Per VLAN Spanning Tree Protocol.
The MAC address of the root bridge is 0017.596d.1580.
SwitchA is not the root bridge, because not all of the interface roles are designated.

Explicação

Questão 101 de 117

Which option contains both the potential networking problem and the protocol or setting that should be used to prevent the problem?

Selecione uma das seguintes:

routing loops, hold down timers
switching loops, split horizon
routing loops, split horizon
switching loops, VTP
routing loops, STP
switching loops, STP

Explicação

Questão 102 de 117

Which two statements are true about interVLAN routing in the topology that is shown in the exhibit? (Choose two.)

Selecione uma ou mais das seguintes:

Host E and host F use the same IP gateway address.
Router1 and Switch2 should be connected via a crossover cable.
Router1 will not play a role in communications between host A and host D.
The FastEthernet 0/0 interface on Router1 must be configured with subinterfaces.
Router1 needs more LAN interfaces to accommodate the VLANs that are shown in the exhibit.
The FastEthernet 0/0 interface on Router1 and the FastEthernet 0/1 interface on Switch2 trunk ports must be configured using the same encapsulation type.

Explicação

Questão 103 de 117

Each of these four switches has been configured with a hostname, as well as being configured to run RSTP. No other configuration changes have been made. Which three of these show the correct RSTP port roles for the indicated switches and interfaces? (Choose three.)

Selecione uma ou mais das seguintes:

SwitchA, Fa0/2, designated
SwitchA, Fa0/1, root
SwitchB, Gi0/2, root
SwitchB, Gi0/1, designated
SwitchC, Fa0/2, root
SwitchD, Gi0/2, root

Explicação

Questão 104 de 117

The network administrator normally establishes a Telnet session with the switch from host A. However, host A is unavailable. The administrator's attempt to telnet to the switch from host B fails, but pings to the other two hosts are successful. What is the issue?

Selecione uma das seguintes:

Host B and the switch need to be in the same subnet.
The switch interface connected to the router is down.
Host B needs to be assigned an IP address in VLAN 1.
The switch needs an appropriate default gateway assigned.
The switch interfaces need the appropriate IP addresses assigned.

Explicação

Questão 105 de 117

Which switch provides the spanning-tree designated port role for the network segment that services the printers?

Selecione uma das seguintes:

Switch1
Switch2
Switch3
Switch4

Explicação

Questão 106 de 117

How many broadcast domains are shown in the graphic assuming only the default VLAN is configured on the switches?

Selecione uma das seguintes:

One
Two
Six
Twelve

Explicação

Questão 107 de 117

The output that is shown is generated at a switch. Which three statements are true? (Choose three.)

Selecione uma ou mais das seguintes:

All ports will be in a state of discarding, learning, or forwarding.
Thirty VLANs have been configured on this switch.
The bridge priority is lower than the default value for spanning tree.
All interfaces that are shown are on shared media.
All designated ports are in a forwarding state.
This switch must be the root bridge for all VLANs on this switch.

Explicação

Questão 108 de 117

At the end of an RSTP election process, which access layer switch port will assume the discarding role?

Selecione uma das seguintes:

Switch3, port fa0/1
Switch3, port fa0/12
Switch4, port fa0/11
Switch4, port fa0/2
Switch3, port Gi0/1
Switch3, port Gi0/2

Explicação

Questão 109 de 117

Which two statements are true of the interfaces on Switch1? (Choose two.)

Selecione uma ou mais das seguintes:

Multiple devices are connected directly to FastEthernet0/1.
A hub is connected directly to FastEthernet0/5.
FastEthernet0/1 is connected to a host with multiple network interface cards.
FastEthernet0/5 has statically assigned MAC addresses.
FastEthernet0/1 is configured as a trunk link.
Interface FastEthernet0/2 has been disabled.

Explicação

Questão 110 de 117

A network technician is asked to design a small network with redundancy. The exhibit represents this design, with all hosts configured in the same VLAN. What conclusions can be made about this design?

Selecione uma das seguintes:

This design will function as intended.
Spanning-tree will need to be used.
The router will not accept the addressing scheme.
The connection between switches should be a trunk.
The router interfaces must be encapsulated with the 802.1Q protocol.

Explicação

Questão 111 de 117

A technician is troubleshooting host connectivity issues on the switches. The hosts in VLANs 10 and 15 on Sw11 are unable to communicate with hosts in the same VLANs on Sw12. Hosts in the Admin VLAN are able to communicate. The port-to-VLAN assignments are identical on the two switches. What could be the problem?

Selecione uma das seguintes:

The Fa0/1 port is not operational on one of the switches.
The link connecting the switches has not been configured as a trunk.
At least one port needs to be configured in VLAN 1 for VLANs 10 and 15 to be able to communicate.
Port FastEthernet 0/1 needs to be configured as an access link on both switches.
A router is required for hosts on SW11 in VLANs 10 and 15 to communicate with hosts in the same VLAN on Sw12.

Explicação

Questão 112 de 117

Given this output for SwitchC, what should the network administrator's next action be?

Selecione uma das seguintes:

Check the trunk encapsulation mode for SwitchC's fa0/1 port.
Check the duplex mode for SwitchC's fa0/1 port.
Check the duplex mode for SwitchA's fa0/2 port.
Check the trunk encapsulation mode for SwitchA's fa0/2 port.

Explicação

Questão 113 de 117

All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)

Selecione uma ou mais das seguintes:

Network A - 172.16.3.48/26
Network A - 172.16.3.128/25
Network A - 172.16.3.192/26
Link A - 172.16.3.0/30
Link A - 172.16.3.40/30
Link A - 172.16.3.112/30

Explicação

Questão 114 de 117

In this VLSM addressing scheme, what summary address would be sent from router A?

Selecione uma das seguintes:

172.16.0.0 /16
172.16.0.0 /20
172.16.0.0 /24
172.32.0.0 /16
172.32.0.0 /17
172.64.0.0 /16

Explicação

Questão 115 de 117

What is the most efficient summarization that R1 can use to advertise its networks to R2?

Selecione uma das seguintes:

172.1.0.0/22
172.1.0.0/21
172.1.4.0/22
172.1.4.0/24
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24
172.1.4.0/25
172.1.4.128/25
172.1.5.0/24
172.1.6.0/24
172.1.7.0/24

Explicação

Questão 116 de 117

A network administrator is adding two new hosts to SwitchA. Which three values could be used for the configuration of these hosts? (Choose three.)

Selecione uma ou mais das seguintes:

host A IP address: 192.168.1.79
host A IP address: 192.168.1.64
host A default gateway: 192.168.1.78
host B IP address: 192.168.1.128
host B default gateway: 192.168.1.129
host B IP address: 192.168.1.190

Explicação

Questão 117 de 117

Which address range efficiently summarizes the routing table of the addresses for router Main?

Selecione uma das seguintes:

172.16.0.0./21
172.16.0.0./20
172.16.0.0./16
172.16.0.0/18

Explicação

["https://cdn.goconqr.com/uploads/multiple_choice_question/image/741272/desktop_q92.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741273/desktop_q93.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741276/desktop_q96.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741756/desktop_q102.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741865/desktop_q1.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741866/desktop_q2.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741869/desktop_q7.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741870/desktop_q5.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741871/desktop_q11.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741872/desktop_q12.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741875/desktop_q15.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741876/desktop_q17.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741879/desktop_q18.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741880/desktop_q21.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741881/desktop_q28.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741884/desktop_q33.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741887/desktop_q41.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741902/desktop_q45.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741905/desktop_q46.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741908/desktop_q47.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741913/desktop_q49.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741915/desktop_q53.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741916/desktop_q54.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741919/desktop_q55.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741923/desktop_q59.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741926/desktop_q62.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741929/desktop_q63.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741933/desktop_q65.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741937/desktop_q66.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741939/desktop_q67.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/741941/desktop_q70.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/741943/desktop_q72.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742623/desktop_q73.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/742624/desktop_q77.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742625/desktop_q81.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742626/desktop_q82.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742627/desktop_q83.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/742628/desktop_q97.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742642/desktop_q109.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742647/desktop_q111.jpg","https://cdn.goconqr.com/uploads/checkbox_question/image/742649/desktop_q115.jpg","https://cdn.goconqr.com/uploads/multiple_choice_question/image/742652/desktop_q117.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/888496/desktop_q7a.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/888497/desktop_q7b.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/888498/desktop_q7c.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/888499/desktop_q7d.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/888500/desktop_q7e.jpg","https://cdn.goconqr.com/uploads/quiz_answer/image/888501/desktop_q7f.jpg"]

	Criado por Axiom42 quase 10 anos atrás

Practice exam for 200-120 exam Questions for the following Topics Topic 1: Operation of IP Data Networks Topic 2: LAN Switching Technologies Topic 3: IP Addressing (IPv4/IPv6)

CCNA Part 1

Questão 1 de 117

Which layer of the OSI reference Model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?

Selecione uma das seguintes:

Explicação

Questão 2 de 117

Which of the following describes the roles of devices in a WAN? (Choose 3)

Selecione uma ou mais das seguintes:

Explicação

Questão 3 de 117

A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation?

Selecione uma das seguintes:

Explicação

Questão 4 de 117

A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?

Selecione uma das seguintes:

Explicação

Questão 5 de 117

A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?

Selecione uma das seguintes:

Explicação

Questão 6 de 117

Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 7 de 117

Which three statements accurately describe Layer 2 Ethernet switches? (Choose three.)

Selecione uma ou mais das seguintes:

Explicação

Questão 8 de 117

Where does routing occur within the DoD TCP/IP reference model?

Selecione uma das seguintes:

Explicação

Questão 9 de 117

For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 10 de 117

In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 11 de 117

Which layer of the OSI reference Model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?

Selecione uma das seguintes:

Explicação

Questão 12 de 117

A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?

Selecione uma das seguintes:

Explicação

Questão 13 de 117

What is the difference between a CSU/DSU and a modem?

Selecione uma das seguintes:

Explicação

Questão 14 de 117

Which port state is introduced by Rapid-PVST?

Selecione uma das seguintes:

Explicação

Questão 15 de 117

VLAN 3 is not yet configured on your switch. What happens if you set the switchport access VLAN 3 command in interface configuration mode?

Selecione uma das seguintes:

Explicação

Questão 16 de 117

What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?

Selecione uma das seguintes:

Explicação

Questão 17 de 117

In a switched environment, what does the IEEE 802.1Q standard describe?

Selecione uma das seguintes:

Explicação

Questão 18 de 117

What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?

Selecione uma das seguintes:

Explicação

Questão 19 de 117

Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 20 de 117

Which switch would STP choose to become the root bridge in the selection process?