Router and Routing Basics Exam Ch 9, 10, 11

Por favor, aguarde! Carregando...

Questão 1 de 65

Which three statements are generally considered to be best practices in the placement of ACLs? (Choose three.)

Selecione uma ou mais das seguintes:

Filter unwanted traffic before it travels onto a low-bandwidth link.
Place extended ACLs close to the destination IP address of the traffic.
Place standard ACLs close to the source IP address of the traffic.
Place extended ACLs close to the source IP address of the traffic
Place standard ACLs close to the destination IP address of the traffic.
For every inbound ACL placed on an interface, there should be a matching outbound ACL.

Explicação

Questão 2 de 65

What two functions describe uses of an access control list? (Choose two.)

Selecione uma ou mais das seguintes:

ACLs can permit or deny traffic based upon the MAC address originating on the router.
ACLs provide a basic level of security for network access.
ACLs assist the router in determining the best path to a destination.
ACLs can control which areas a host can access on a network.
Standard ACLs can restrict access to specific applications and ports.

Explicação

Questão 3 de 65

An administrator has configured an access list on R1 to allow SSH administrative access from host 172.16.1.100. Which command correctly applies the ACL?

Selecione uma das seguintes:

R1(config-line)# access-class 1 out
R1(config-if)# ip access-group 1 out
R1(config-if)# ip access-group 1 in
R1(config-line)# access-class 1 in

Explicação

Questão 4 de 65

Refer to the exhibit. What is the result of adding the established argument to the end of the ACE?

Selecione uma das seguintes:

Any IP traffic is allowed to reach the 192.168.254.0 255.255.254.0 network as long as it is in response to an originated request.
Any traffic is allowed to reach the 192.168.254.0 255.255.254.0 network.
192.168.254.0 /23 traffic is allowed to reach any network.
Any TCP traffic is allowed to reach the 192.168.254.0 255.255.254.0 network if it is in response to an originated request.

Explicação

Questão 5 de 65

Refer to the exhibit. What will happen to the access list 10 ACEs if the router is rebooted before any other commands are implemented?

Selecione uma das seguintes:

The ACEs of access list 10 will be deleted.
The ACEs of access list 10 wildcard masks will be converted to subnet masks.
The ACEs of access list 10 will not be affected.
The ACEs of access list 10 will be renumbered.

Explicação

Questão 6 de 65

Which three statements describe ACL processing of packets? (Choose three.)

Selecione uma ou mais das seguintes:

A packet that does not match the conditions of any ACE will be forwarded by default.
Each statement is checked only until a match is detected or until the end of the ACE list.
A packet can either be rejected or forwarded as directed by the ACE that is matched.
A packet that has been denied by one ACE can be permitted by a subsequent ACE.
Each packet is compared to the conditions of every ACE in the ACL before a forwarding decision is made.
An implicit deny any rejects any packet that does not match any ACE.

Explicação

Questão 7 de 65

In which configuration would an outbound ACL placement be preferred over an inbound ACL placement?

Selecione uma das seguintes:

when the ACL is applied to an outbound interface to filter packets coming from multiple inbound interfaces before the packets exit the interface
when a router has more than one ACL
when an outbound ACL is closer to the source of the traffic flow
when an interface is filtered by an outbound ACL and the network attached to the interface is the source network being filtered within the ACL

Explicação

Questão 8 de 65

Refer to the exhibit. A router has an existing ACL that permits all traffic from the 172.16.0.0 network. The administrator attempts to add a new ACE to the ACL that denies packets from host 172.16.0.1 and receives the error message that is shown in the exhibit. What action can the administrator take to block packets from host 172.16.0.1 while still permitting all other traffic from the 172.16.0.0 network?

Selecione uma das seguintes:

Add a deny any any ACE to access-list 1.
Create a second access list denying the host and apply it to the same interface.
Manually add the new deny ACE with a sequence number of 5.
Manually add the new deny ACE with a sequence number of 15.

Explicação

Questão 9 de 65

What packets would match the access control list statement that is shown below?
access-list 110 permit tcp 172.16.0.0 0.0.0.255 any eq 22

Selecione uma das seguintes:

any TCP traffic from any host to the 172.16.0.0 network
SSH traffic from the 172.16.0.0 network to any destination network
any TCP traffic from the 172.16.0.0 network to any destination network
SSH traffic from any source network to the 172.16.0.0 network

Explicação

Questão 10 de 65

If a router has two interfaces and is routing both IPv4 and IPv6 traffic, how many ACLs could be created and applied to it?

Selecione uma das seguintes:

Explicação

Questão 11 de 65

Which feature is unique to IPv6 ACLs when compared to those of IPv4 ACLs?

Selecione uma das seguintes:

the use of wildcard masks
an implicit deny any any ACE
an implicit permit of neighbor discovery packets
the use of named ACL entries

Explicação

Questão 12 de 65

Consider the following access list that allows IP phone configuration file transfers from a particular host to a TFTP server:
R1(config)# access-list 105 permit udp host 10.0.70.23 host 10.0.54.5 range 1024 5000
R1(config)# access-list 105 deny ip any any
R1(config)# interface gi0/0
R1(config-if)# ip access-group 105 out
Which method would allow the network administrator to modify the ACL and include FTP transfers from any source IP address?

Selecione uma das seguintes:

R1(config)# access-list 105 permit udp host 10.0.70.23 host 10.0.54.5 range 1024 5000
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 20
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 21
R1(config)# access-list 105 deny ip any any
R1(config)# interface gi0/0
R1(config-if)# no ip access-group 105 out
R1(config)# no access-list 105
R1(config)# access-list 105 permit udp host 10.0.70.23 host 10.0.54.5 range 1024 5000
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 20
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 21
R1(config)# access-list 105 deny ip any any
R1(config)# interface gi0/0
R1(config-if)# ip access-group 105 out
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 20
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 21
R1(config)# interface gi0/0
R1(config-if)# no ip access-group 105 out
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 20
R1(config)# access-list 105 permit tcp any host 10.0.54.5 eq 21
R1(config)# interface gi0/0
R1(config-if)# ip access-group 105 out

Explicação

Questão 13 de 65

Which IPv6 ACL command entry will permit traffic from any host to an SMTP server on network 2001:DB8:10:10::/64?

Selecione uma das seguintes:

permit tcp host 2001:DB8:10:10::100 any eq 25
permit tcp any host 2001:DB8:10:10::100 eq 25
permit tcp any host 2001:DB8:10:10::100 eq 23
permit tcp host 2001:DB8:10:10::100 any eq 23

Explicação

Questão 14 de 65

What is the only type of ACL available for IPv6?

Selecione uma das seguintes:

numbered standard
numbered extended
named standard
named extended

Explicação

Questão 15 de 65

What method is used to apply an IPv6 ACL to a router interface?

Selecione uma das seguintes:

the use of the ipv6 access-list command
the use of the ip access-group command
the use of the ipv6 traffic-filter command
the use of the access-class command

Explicação

Questão 16 de 65

A network administrator needs to configure a standard ACL so that only the workstation of the administrator with the IP address 192.168.15.23 can access the virtual terminal of the main router. Which two configuration commands can achieve the task? (Choose two.)

Selecione uma ou mais das seguintes:

Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.255
Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.255
Router1(config)# access-list 10 permit host 192.168.15.23
Router1(config)# access-list 10 permit 192.168.15.23 255.255.255.0
Router1(config)# access-list 10 permit 192.168.15.23 0.0.0.0

Explicação

Questão 17 de 65

Which statement describes a difference between the operation of inbound and outbound ACLs?

Selecione uma das seguintes:

On a network interface, more than one inbound ACL can be configured but only one outbound ACL can be configured.
Inbound ACLs are processed before the packets are routed while outbound ACLs are processed after the routing is completed.
In contrast to outbound ALCs, inbound ACLs can be used to filter packets with multiple criteria.
Inbound ACLs can be used in both routers and switches but outbound ACLs can be used only on routers.

Explicação

Questão 18 de 65

What single access list statement matches all of the following networks?
192.168.16.0
192.168.17.0
192.168.18.0
192.168.19.0

Selecione uma das seguintes:

access-list 10 permit 192.168.16.0 0.0.15.255
access-list 10 permit 192.168.0.0 0.0.15.255
access-list 10 permit 192.168.16.0 0.0.3.255
access-list 10 permit 192.168.16.0 0.0.0.255

Explicação

Questão 19 de 65

Which three implicit access control entries are automatically added to the end of an IPv6 ACL? (Choose three.)

Selecione uma ou mais das seguintes:

permit ipv6 any any
deny ip any any
permit icmp any any nd-ns
deny ipv6 any any
deny icmp any any
permit icmp any any nd-na

Explicação

Questão 20 de 65

What is a limitation when utilizing both IPv4 and IPv6 ACLs on a router?

Selecione uma das seguintes:

IPv4 ACLs can be numbered or named whereas IPv6 ACLs must be numbered.
Both IPv4 and IPv6 ACLs can be configured on a single device, but cannot share the same name.
A device can run only IPv4 ACLs or IPv6 ACLs.
IPv6 ACLs perform the same functions as standard IPv4 ACLs.

Explicação

Questão 21 de 65

Refer to the exhibit. The network administrator that has the IP address of 10.0.70.23/25 needs to have access to the corporate FTP server (10.0.54.5/28). The FTP server is also a web server that is accessible to all internal employees on networks within the 10.x.x.x address. No other traffic should be allowed to this server. Which extended ACL would be used to filter this traffic, and how would this ACL be applied? (Choose two.)

Selecione uma ou mais das seguintes:

access-list 105 permit tcp host 10.0.54.5 any eq www
access-list 105 permit tcp host 10.0.70.23 host 10.0.54.5 eq 20
access-list 105 permit tcp host 10.0.70.23 host 10.0.54.5 eq 21
access-list 105 permit ip host 10.0.70.23 host 10.0.54.5
access-list 105 permit tcp any host 10.0.54.5 eq www
access-list 105 permit ip any any
R2(config)# interface gi0/0
R2(config-if)# ip access-group 105 in
R1(config)# interface gi0/0
R1(config-if)# ip access-group 105 out
access-list 105 permit tcp host 10.0.70.23 host 10.0.54.5 eq 20
access-list 105 permit tcp host 10.0.70.23 host 10.0.54.5 eq 21
access-list 105 permit tcp 10.0.0.0 0.255.255.255 host 10.0.54.5 eq www
access-list 105 deny ip any host 10.0.54.5
access-list 105 permit ip any any
R1(config)# interface s0/0/0
R1(config-if)# ip access-group 105 out

Explicação

Questão 22 de 65

Refer to the exhibit. The IPv6 access list LIMITED_ACCESS is applied on the S0/0/0 interface of R1 in the inbound direction. Which IPv6 packets from the ISP will be dropped by the ACL on R1?

Selecione uma das seguintes:

neighbor advertisements that are received from the ISP router
ICMPv6 packets that are destined to PC1
HTTPS packets to PC1
packets that are destined to PC1 on port 80

Explicação

Questão 23 de 65

Which two characteristics are shared by both standard and extended ACLs? (Choose two.)

Selecione uma ou mais das seguintes:

Both can be created by using either a descriptive name or number.
Both filter packets for a specific destination host IP address.
Both include an implicit deny as a final entry
Both kinds of ACLs can filter based on protocol type.
Both can permit or deny specific services by port number.

Explicação

Questão 24 de 65

Refer to the exhibit. Based on the output that is shown, what kind of IPv6 addressing is being configured?

Selecione uma das seguintes:

static link-local
stateless DHCPv6
stateful DHCPv6
SLAAC

Explicação

Questão 25 de 65

As a DHCPv4 client lease is about to expire, what is the message that the client sends the DHCP server?

Selecione uma das seguintes:

DHCPREQUEST
DHCPACK
DHCPOFFER
DHCPDISCOVER

Explicação

Questão 26 de 65

A network administrator configures a router to send RA messages with M flag as 0 and O flag as 1. Which statement describes the effect of this configuration when a PC tries to configure its IPv6 address?

Selecione uma das seguintes:

It should contact a DHCPv6 server for the prefix, the prefix-length information, and an interface ID that is both random and unique.
It should contact a DHCPv6 server for all the information that it needs.
It should use the information that is contained in the RA message exclusively.
It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.

Explicação

Questão 27 de 65

Refer to the exhibit. A network administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain name information configured in the DHCP pool. What could be the cause of the problem?

Selecione uma das seguintes:

The GigabitEthernet interface is not activated.
The clients cannot communicate with the DHCPv6 server, evidenced by the number of active clients being 0.
The router is configured for SLAAC operation.
The DNS server address is not on the same network as the clients are on.

Explicação

Questão 28 de 65

What is an advantage of configuring a Cisco router as a relay agent?

Selecione uma das seguintes:

It reduces the response time from a DHCP server.
It can forward both broadcast and multicast messages on behalf of clients.
It can provide relay services for multiple UDP services.
It will allow DHCPDISCOVER messages to pass without alteration.

Explicação

Questão 29 de 65

Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server?

Selecione uma das seguintes:

Add the ipv6 dhcp relay command to interface Fa0/0.
Configure the ipv6 nd managed-config-flag command on interface Fa0/1.
Add the IPv6 address 2001:DB8:1234:5678::10/64 to the interface configuration of the DHCPv6 server
Change the ipv6 nd managed-config-flag command to ipv6 nd other-config-flag.

Explicação

Questão 30 de 65

Refer to the exhibit. A network administrator is implementing stateful DHCPv6 operation for the company. However, the clients are not using the prefix and prefix-length information that is configured in the DHCP pool. The administrator issues a show ipv6 interface command. What could be the cause of the problem?

Selecione uma das seguintes:

No virtual link-local address is configured
The Duplicate Address Detection feature is disabled.
The router is configured for SLAAC DHCPv6 operation
The router is configured for stateless DHCPv6 operation

Explicação

Questão 31 de 65

Under which two circumstances would a router usually be configured as a DHCPv4 client? (Choose two.)

Selecione uma ou mais das seguintes:

This is an ISP requirement.
The administrator needs the router to act as a relay agent.
The router is intended to be used as a SOHO gateway.
The router is meant to provide IP addresses to the hosts.
The router has a fixed IP address.

Explicação

Questão 32 de 65

What is the reason why the DHCPREQUEST message is sent as a broadcast during the DHCPv4 process?

Selecione uma das seguintes:

to notify other hosts not to request the same IP address
for routers to fill their routing tables with this new information
for hosts on other subnets to receive the information
to notify other DHCP servers on the subnet that the IP address was leased

Explicação

Questão 33 de 65

A company implements the stateless DHCPv6 method for configuring IPv6 addresses on employee workstations. After a workstation receives messages from multiple DHCPv6 servers to indicate their availability for DHCPv6 service, which message does it send to a server for configuration information?

Selecione uma das seguintes:

DHCPv6 ADVERTISE
DHCPv6 INFORMATION-REQUEST
DHCPv6 SOLICIT
DHCPv6 REQUEST

Explicação

Questão 34 de 65

A network administrator is implementing DHCPv6 for the company. The administrator configures a router to send RA messages with M flag as 1 by using the interface command ipv6 nd managed-config-flag. What effect will this configuration have on the operation of the clients?

Selecione uma das seguintes:

Clients must use the information that is contained in RA messages.
Clients must use the prefix and prefix length that are provided by a DHCPv6 server and generate a random interface ID.
Clients must use the prefix and prefix length that are provided by RA messages and obtain additional information from a DHCPv6 server.
Clients must use all configuration information that is provided by a DHCPv6 server.

Explicação

Questão 35 de 65

Which set of commands will configure a router as a DHCP server that will assign IPv4 addresses to the 192.168.100.0/23 LAN while reserving the first 10 and the last addresses for static assignment?

Selecione uma das seguintes:

ip dhcp excluded-address 192.168.100.1 192.168.100.10
ip dhcp excluded-address 192.168.101.254
ip dhcp pool LAN-POOL-100
network 192.168.100.0 255.255.254.0
default-router 192.168.100.1
ip dhcp excluded-address 192.168.100.1 192.168.100.10
ip dhcp excluded-address 192.168.100.254
ip dhcp pool LAN-POOL-100
network 192.168.100.0 255.255.255.0
ip default-gateway 192.168.100.1
dhcp pool LAN-POOL-100
ip dhcp excluded-address 192.168.100.1 192.168.100.9
ip dhcp excluded-address 192.168.100.254
network 192.168.100.0 255.255.254.0
default-router 192.168.101.1
ip dhcp excluded-address 192.168.100.1 192.168.100.9
ip dhcp excluded-address 192.168.101.254
ip dhcp pool LAN-POOL-100
ip network 192.168.100.0 255.255.254.0
ip default-gateway 192.168.100.1

Explicação

Questão 36 de 65

What is used in the EUI-64 process to create an IPv6 interface ID on an IPv6 enabled interface?

Selecione uma das seguintes:

a randomly generated 64-bit hexadecimal address
an IPv4 address that is configured on the interface
the MAC address of the IPv6 enabled interface
an IPv6 address that is provided by a DHCPv6 server

Explicação

Questão 37 de 65

An administrator wants to configure hosts to automatically assign IPv6 addresses to themselves by the use of Router Advertisement messages, but also to obtain the DNS server address from a DHCPv6 server. Which address assignment method should be configured?

Selecione uma das seguintes:

SLAAC
RA and EUI-64
stateless DHCPv6
stateful DHCPv6

Explicação

Questão 38 de 65

Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server?

Selecione uma das seguintes:

broadcast DHCPREQUEST
unicast DHCPREQUEST
unicast DHCPACK
broadcast DHCPACK

Explicação

Questão 39 de 65

A host on the 10.10.100.0/24 LAN is not being assigned an IPv4 address by an enterprise DHCP server with the address 10.10.200.10/24. What is the best way for the network engineer to resolve this problem?

Selecione uma das seguintes:

Issue the command ip helper-address 10.10.100.0 on the router interface that is the 10.10.200.0/24 gateway.
Issue the command default-router 10.10.200.10 at the DHCP configuration prompt on the 10.10.100.0/24 LAN gateway router.
Issue the command network 10.10.200.0 255.255.255.0 at the DHCP configuration prompt on the 10.10.100.0/24 LAN gateway router.
Issue the command ip helper-address 10.10.200.10 on the router interface that is the 10.10.100.0/24 gateway.

Explicação

Questão 40 de 65

A company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway?

Selecione uma das seguintes:

the global unicast address of the router interface that is attached to the network
the unique local address of the router interface that is attached to the network
the link-local address of the router interface that is attached to the network
the all-routers multicast address

Explicação

Questão 41 de 65

Which address does a DHCPv4 server target when sending a DHCPOFFER message to a client that makes an address request?

Selecione uma das seguintes:

client hardware address
client IP address
broadcast MAC address
gateway IP address

Explicação

Questão 42 de 65

An administrator issues the commands:
Router(config)# interface g0/1
Router(config-if)# ip address dhcp
What is the administrator trying to achieve?

Selecione uma das seguintes:

configuring the router to obtain IP parameters from a DHCPv4 server
configuring the router to act as a relay agent
configuring the router to resolve IP address conflicts
configuring the router to act as a DHCPv4 server

Explicação

Questão 43 de 65

How does an IPv6 client ensure that it has a unique address after it configures its IPv6 address using the SLAAC allocation method?

Selecione uma das seguintes:

It sends an ARP message with the IPv6 address as the destination IPv6 address.
It checks with the IPv6 address database that is hosted by the SLAAC server.
It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address.
It contacts the DHCPv6 server via a special formed ICMPv6 message.

Explicação

Questão 44 de 65

What are two of the required steps to configure PAT? (Choose two.)

Selecione uma ou mais das seguintes:

fine the hello and interval timers to match the adjacent neighbor router
Define the range of source ports to be used.
Identify the inside interface.
Create a standard access list to define applications that should be translated.
Define a pool of global addresses to be used for overload translation.

Explicação

Questão 45 de 65

Several key servers in an organization must be directly accessible from the Internet. What addressing policy should be implemented for these servers?

Selecione uma das seguintes:

Use DHCP to assign addresses from the pool of Class B addresses.
Use dynamic NAT to provide addresses for the servers.
Assign static internal addresses and public external addresses to each of the servers.
Place all of the servers in their own Class C private subnet.

Explicação

Questão 46 de 65

Which configuration would be appropriate for a small business that has the public IP address of 209.165.200.225/30 assigned to the external interface on the router that connects to the Internet?

Selecione uma das seguintes:

access-list 1 permit 10.0.0.0 0.255.255.255
ip nat pool comp 192.168.2.1 192.168.2.8 netmask 255.255.255.240
ip nat inside source list 1 pool comp overload
ip nat inside source static 10.0.0.5 209.165.200.225
access-list 1 permit 10.0.0.0 0.255.255.255
ip nat pool comp 192.168.2.1 192.168.2.8 netmask 255.255.255.240
ip nat inside source list 1 pool comp
access-list 1 permit 10.0.0.0 0.255.255.255
ip nat inside source list 1 interface serial 0/0/0 overload
access-list 1 permit 10.0.0.0 0.255.255.255
ip nat pool comp 192.168.2.1 192.168.2.8 netmask 255.255.255.240
ip nat inside source list 1 pool comp overload

Explicação

Questão 47 de 65

Typically, which network device would be used to perform NAT for a corporate environment?

Selecione uma das seguintes:

server
DHCP server
router
host device
switch

Explicação

Questão 48 de 65

Refer to the exhibit. The NAT configuration applied to the router is as follows:
ERtr(config)# access-list 1 permit 10.0.0.0 0.255.255.255
ERtr(config)# ip nat pool corp 209.165.201.6 209.165.201.30 netmask 255.255.255.224
ERtr(config)# ip nat inside source list 1 pool corp overload
ERtr(config)# ip nat inside source static 10.10.10.55 209.165.201.4
ERtr(config)# interface gigabitethernet 0/0
ERtr(config-if)# ip nat inside
ERtr(config-if)# interface serial 0/0/0
ERtr(config-if)# ip nat outside
Based on the configuration and the output shown, what can be determined about the NAT status within the organization?

Selecione uma das seguintes:

Static NAT is working, but dynamic NAT is not.
NAT is working.
Dynamic NAT is working, but static NAT is not.
Not enough information is given to determine if both static and dynamic NAT are working.

Explicação

Questão 49 de 65

Refer to the exhibit. Based on the output that is shown, what type of NAT has been implemented?

Selecione uma das seguintes:

dynamic NAT with a pool of two public IP addresses
static NAT with one entry
static NAT with a NAT pool
PAT using an external interface

Explicação

Questão 50 de 65

What is a disadvantage of NAT?

Selecione uma das seguintes:

The costs of readdressing hosts can be significant for a publicly addressed network
The router does not need to alter the checksum of the IPv4 packets.
The internal hosts have to use a single public IPv4 address for external communication
There is no end-to-end addressing.

Explicação

Questão 51 de 65

A network engineer has configured a router with the command ip nat inside source list 4 pool corp overload. Why did the engineer use the overload option?

Selecione uma das seguintes:

The company has a small number of servers that should be accessible by clients from the Internet.
The company router must throttle or buffer traffic because the processing power of the router is not enough to handle the normal load of external-bound Internet traffic.
The company has more private IP addresses than available public IP addresses.
The company needs to have more public IP addresses available to be used on the Internet.

Explicação

Questão 52 de 65

Refer to the exhibit. R1 is configured for NAT as displayed. What is wrong with the configuration?

Selecione uma das seguintes:

Interface Fa0/0 should be identified as an outside NAT interface
NAT-POOL2 is not bound to ACL 1.
Access-list 1 is misconfigured.
The NAT pool is incorrect.

Explicação

Questão 53 de 65

A network administrator is configuring a static NAT on the border router for a web server located in the DMZ network. The web server is configured to listen on TCP port 8080. The web server is paired with the internal IP address of 192.168.5.25 and the external IP address of 209.165.200.230. For easy access by hosts on the Internet, external users do not need to specify the port when visiting the web server. Which command will configure the static NAT?

Selecione uma das seguintes:

R1(config)# ip nat inside source static tcp 209.165.200.230 8080 192.168.5.25 80
R1(config)# ip nat inside source static tcp 192.168.5.25 80 209.165.200.230 8080
R1(config)# ip nat inside source static tcp 209.165.200.230 80 192.168.5.25 8080
R1(config)# ip nat inside source static tcp 192.168.5.25 8080 209.165.200.230 80

Explicação

Questão 54 de 65

Which statement accurately describes dynamic NAT?

Selecione uma das seguintes:

It provides an automated mapping of inside local to inside global IP addresses
It always maps a private IP address to a public IP address.
It dynamically provides IP addressing to internal hosts.
It provides a mapping of internal host names to IP addresses.

Explicação

Questão 55 de 65

When dynamic NAT without overloading is being used, what happens if seven users attempt to access a public server on the Internet when only six addresses are available in the NAT pool?

Selecione uma das seguintes:

All users can access the server.
No users can access the server.
The first user gets disconnected when the seventh user makes the request
The request to the server for the seventh user fails

Explicação

Questão 56 de 65

What is an advantage of deploying IPv4 NAT technology for internal hosts in an organization?

Selecione uma das seguintes:

provides flexibility in designing the IPv4 addressing scheme
makes internal network access easy for outside hosts using UDP
enables the easy deployment of applications that require end-to-end traceability
increases the performance of packet transmission to the Internet

Explicação

Questão 57 de 65

What is a characteristic of unique local addresses?

Selecione uma das seguintes:

They are defined in RFC 3927
They allow sites to be combined without creating any address conflicts.
They are designed to improve the security of IPv6 networks.
Their implementation depends on ISPs providing the service

Explicação

Questão 58 de 65

What is the purpose of port forwarding?

Selecione uma das seguintes:

Port forwarding allows for translating inside local IP addresses to outside local addresses.
Port forwarding allows an external user to reach a service on a private IPv4 address that is located inside a LAN.
Port forwarding allows users to reach servers on the Internet that are not using standard port numbers.
Port forwarding allows an internal user to reach a service on a public IPv4 address that is located outside a LAN.

Explicação

Questão 59 de 65

Using NAT terminology, what is the address of the source host on a private network as seen from inside the network?

Selecione uma das seguintes:

outside local
inside local
inside global
outside global

Explicação

Questão 60 de 65

Refer to the exhibit. What is the purpose of the command marked with an arrow shown in the partial configuration output of a Cisco broadband router?

Selecione uma das seguintes:

defines which addresses are allowed out of the router
defines which addresses are assigned to a NAT pool
defines which addresses are allowed into the router
defines which addresses can be translated

Explicação

Questão 61 de 65

Which type of NAT maps a single inside local address to a single inside global address?

Selecione uma das seguintes:

dynamic
static
port address translation
overloading

Explicação

Questão 62 de 65

A network administrator configures the border router with the command R1(config)# ip nat inside source list 4 pool corp. What is required to be configured in order for this particular command to be functional?

Selecione uma das seguintes:

an access list named corp that defines the private addresses that are affected by NAT
a VLAN named corp to be enabled and active and routed by R1
an access list numbered 4 that defines the starting and ending public IP addresses
a NAT pool named corp that defines the starting and ending public IP addresses
ip nat outside to be enabled on the interface that connects to the LAN affected by the NAT

Explicação

Questão 63 de 65

What is the primary purpose of NAT?

Selecione uma das seguintes:

allow peer-to-peer file sharing
enhance network performance
increase network security
conserve IPv4 addresses

Explicação

Questão 64 de 65

Refer to the exhibit. What has to be done in order to complete the static NAT configuration on R1?

Selecione uma das seguintes:

R1 should be configured with the command ip nat inside source static 209.165.200.1 192.168.11.11.
R1 should be configured with the command ip nat inside source static 209.165.200.200 192.168.11.11.
Interface Fa0/0 should be configured with the command no ip nat inside
Interface S0/0/0 should be configured with the command ip nat outside.

Explicação

Questão 65 de 65

Refer to the exhibit. What will be the effect of entering the command that is shown in the exhibit on R2 as part of the dynamic NAT configuration?

Selecione uma das seguintes:

It will bind NAT-POOL1 with ACL 1.
It will identify an inside NAT interface.
It will define the source ACL for the external interface
It will define a pool of addresses for translation

Explicação

Verificar resposta

["https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235264/desktop_23dae704-976d-4f5a-8a8e-bd3787e61d31.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235266/desktop_cba44e22-ad58-4a16-aec1-e4c056c3dd2e.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235278/desktop_a57271f0-d75b-49ad-ac6f-b375774a6576.png","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2235343/desktop_20f64bfd-cbca-43fd-be85-263973a07d43.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235350/desktop_59e8b2c7-0e39-4f72-a31a-811977ad3ded.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235392/desktop_e6a57aad-0652-4cc1-845d-fe70f36bbc29.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235415/desktop_e435dc93-27b9-4368-a3cd-bf124f631f2d.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235430/desktop_1b839591-9c51-4696-8823-db4864fcda41.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235440/desktop_16c6e691-255e-4274-96c3-654479e65cd5.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235509/desktop_56149f3f-4c85-4155-b2f5-cd5e0eeb5099.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235513/desktop_aed59636-65b9-4ec0-a02d-52648bd81f73.png","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235520/desktop_f798a06e-50a1-412c-952a-0b712de3a6f5.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235538/desktop_533f020a-7281-44bb-b3a2-cd5f13f6a22c.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235555/desktop_23ac1dcf-35db-473e-9f55-4f03dc41926a.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/multiple_choice_question/image/2235563/desktop_5fc4921f-2b41-46db-9b1d-598fa4e4f33c.png"]

	Criado por Anthony Schulmeister quase 11 anos atrás