Brian Gamble
Quiz por , criado more than 1 year ago

Final / Review ICND 1 Quiz sobre DIKTA ICND 1 Ch 8, criado por Brian Gamble em 25-02-2016.

30
0
0
Brian Gamble
Criado por Brian Gamble mais de 8 anos atrás
Fechar

DIKTA ICND 1 Ch 8

Questão 1 de 7

1

Imagine that you have configured the enable secret command, followed by the enable password command, from the console. You log out of the switch and log back in at the console. Which command defines the password that you had to enter to access privileged mode?

Selecione uma das seguintes:

  • enable password

  • enable secret

  • Neither

  • The password command, if it’s configured

Explicação

Questão 2 de 7

1

An engineer had formerly configured a Cisco 2960 switch to allow Telnet access so that the switch expected a password of mypassword from the Telnet user. The engineer then changed the configuration to support Secure Shell. Which of the following commands could have been part of the new configuration? (Choose two answers.)

Selecione uma ou mais das seguintes:

  • A username name password password vty mode sub command

  • A username name password password global configuration command

  • A login local vty mode sub command

  • A transport input ssh global configuration command

Explicação

Questão 3 de 7

1

The following command was copied and pasted into configuration mode when a user was telnetted into a Cisco switch:

banner login this is the login banner

Which of the following is true about what occurs the next time a user logs in from
the console?

Selecione uma das seguintes:

  • No banner text is displayed.

  • The banner text “his is” is displayed.

  • The banner text “this is the login banner” is displayed.

  • The banner text “Login banner configured, no text defined” is displayed.

Explicação

Questão 4 de 7

1

Which of the following is required when configuring port security with sticky learning?

Selecione uma das seguintes:

  • Setting the maximum number of allowed MAC addresses on the interface with
    the switchport port-security maximum interface subcommand

  • Enabling port security with the switchport port-security interface subcommand

  • Defining the specific allowed MAC addresses using the switchport port-security
    mac-address interface subcommand

  • All the other answers list required commands

Explicação

Questão 5 de 7

1

An engineer’s desktop PC connects to a switch at the main site. A router at the main site connects to each branch office through a serial link, with one small router and switch at each branch. Which of the following commands must be configured on the branch office switches, in the listed configuration mode, to allow the engineer to telnet to the branch office switches? (Choose three answers.)

Selecione uma ou mais das seguintes:

  • The ip address command in interface configuration mode

  • The ip address command in global configuration mode

  • The ip default-gateway command in VLAN configuration mode

  • The ip default-gateway command in global configuration mode

  • The password command in console line configuration mode

  • The password command in vty line configuration mode

Explicação

Questão 6 de 7

1

Which of the following describes a way to disable IEEE standard autonegotiation on a 10/100 port on a Cisco switch?

Selecione uma das seguintes:

  • Configure the negotiate disable interface subcommand

  • Configure the no negotiate interface subcommand

  • Configure the speed 100 interface subcommand

  • Configure the duplex half interface subcommand

  • Configure the duplex full interface subcommand

  • Configure the speed 100 and duplex full interface subcommands

Explicação

Questão 7 de 7

1

In which of the following modes of the CLI could you configure the duplex setting for interface Fast Ethernet 0/5?

Selecione uma das seguintes:

  • User mode

  • Enable mode

  • Global configuration mode

  • VLAN mode

  • Interface configuration mode

Explicação