Examen CCNA Certificacion Test

Questão 1 de 43

1

Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?

Selecione uma das seguintes:

transport
network
presentation
session
application

Explicação

Questão 2 de 43

1

A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?

Selecione uma das seguintes:

This is a 10 Mb/s switch port.
This is a 100 Mb/s switch port.
This is an Ethernet port operating at half duplex.
This is an Ethernet port operating at full duplex.
This is a port on a network interface card in a PC.

Explicação

Questão 3 de 43

1

A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?

Selecione uma das seguintes:

physical
session
data link
transport
network

Explicação

Questão 4 de 43

1

Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two)

Selecione uma ou mais das seguintes:

The transport layer divides a data stream into segments and may add reliability and flow control information.
The data link layer adds physical source and destination addresses and an FCS to the segment.
Packets are created when the network layer encapsulates a frame with source and destination host addresses and protocol-related control information.
Packets are created when the network layer adds Layer 3 addresses and control information to a segment.
The presentation layer translates bits into voltages for transmission across the physical link.

Explicação

Questão 5 de 43

1

Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server?

Selecione uma das seguintes:

The MAC address of the server network interface
The MAC address of host A
The MAC address of router interface e1
The MAC address of router interface e0

Explicação

Questão 6 de 43

1

Refer to the exhibit.

What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)

Selecione uma ou mais das seguintes:

The number of broadcast domains would remain the same.
The number of collision domains would increase.
The number of collision domains would decrease.
The number of broadcast domains would decrease.
The number of collision domains would remain the same.
he number of broadcast domains would increase.

Explicação

Questão 7 de 43

1

For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)

Selecione uma ou mais das seguintes:

To uniquely identify devices at Layer 2
To allow communication with devices on a different network
To differentiate a Layer 2 frame from a Layer 3 packet
To establish a priority system to determine which device gets to transmit first
To allow communication between different devices on the same network
To allow detection of a remote device when its physical address is unknown

Explicação

Questão 8 de 43

1

In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)

Selecione uma ou mais das seguintes:

When they receive a special token
when there is a carrier
When they detect no other devices are sending
When the medium is idle
When the server grants access

Explicação

Questão 9 de 43

1

Which of the following statements describe the network shown in the graphic?

What are the proper statements?. (Choose two)

Selecione uma ou mais das seguintes:

There are two broadcast domains in the network.
There are four broadcast domains in the network.
There are six broadcast domains in the network.
There are four collision domains in the network. in the network.
There are five collision domains in the network.
There are seven collision domains

Explicação

Questão 10 de 43

1

How many broadcast domains are shown in the graphic assuming only the default VLAN is configured on the switches?

Selecione uma das seguintes:

one
six
twelve
two

Explicação

Questão 11 de 43

1

What is the first 24 bits in a MAC address called?

Selecione uma das seguintes:

NIC
BIA
OUI
VAI

Explicação

Questão 12 de 43

1

A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server.

What is the highest layer of the protocol stack that the network administrator is using for this operation?

Selecione uma das seguintes:

Application
Presentation
Session
Transport
Internet
data link

Explicação

Questão 13 de 43

1

Where does routing occur within the DoD TCP/IP reference model?

Selecione uma das seguintes:

Application
Internet
Network
Transport

Explicação

Questão 14 de 43

1

Which statement describes the process of dynamically assigning IP addresses by the DHCP server?

Selecione uma das seguintes:

Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
Addresses are permanently assigned so that the hosts uses the same address at all times.
Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.
Addresses are leased to hosts, which periodically contact the DHCP server to renew the lease.

Explicação

Questão 15 de 43

1

How does a DHCP server dynamically assign IP addresses to hosts?

Selecione uma das seguintes:

Addresses are allocated after a negotiation between the server and the host to determine the length of the agreement.
Addresses are permanently assigned so that the hosts uses the same address at all times.
Addresses are assigned for a fixed period of time, at the end of the period, a new request for an address must be made.
Addresses are leased to hosts. A host will usually keep the same address by periodically contacting the DHCP server to renew the lease.

Explicação

Questão 16 de 43

1

Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.)

Selecione uma ou mais das seguintes:

Set the IP gateway to be used by the network.
Perform host discovery used DHCPDISCOVER message.
Configure IP address parameters from DHCP server to a host.
Provide an easy management of layer 3 devices.
Monitor IP performance using the DHCP server.
Assign and renew IP address from the default pool.

Explicação

Questão 17 de 43

1

Which statement is correct regarding the operation of DHCP?

Selecione uma das seguintes:

A DHCP client uses a ping to detect address conficts.
A DHCP server uses a gratuitous ARP to detect DHCP clients.
A DHCP client uses a gratuitous ARP to detect a DHCP server.
f an address conflict is detected, the address is removed from the pool and an administrator must resolve the conflict.
If an address conflict is detected, the address is removed from the pool for an amount of time configurable by the administrator.
If an address conflict is detected, the address is removed from the pool and will not be reused until the server is rebooted.

Explicação

Questão 18 de 43

1

Refer to the exhibit.
Host A pings interface S0/0 on router 3. What is the TTL value for that ping?

Selecione uma das seguintes:

252
253
254
255

Explicação

Questão 19 de 43

1

Which command can be used from a PC to verify the connectivity between hosts that connect through a switch in the same LAN?

Selecione uma das seguintes:

Ping address
Tracert address
Traceroute address
Arp address

Explicação

Questão 20 de 43

1

An administrator must assign static IP addresses to the servers in a network. For network 192.168.20.24/29, the router is assigned the first usable host address while the sales server is given the last usable host address. Which of the following should be entered into the IP properties box for the sales server?

Selecione uma das seguintes:

- IP address: 192.168.20.14
- Subnet Mask: 255.255.255.248
- Default Gateway: 192.168.20.9
- IP address: 192.168.20.254
- Subnet Mask: 255.255.255.0
- Default Gateway: 192.168.20.1
- P address: 192.168.20.30
- Subnet Mask: 255.255.255.248
- Default Gateway: 192.168.20.25
- IP address: 192.168.20.30
- Subnet Mask: 255.255.255.240
- Default Gateway: 192.168.20.17
- IP address: 192.168.20.30
- Subnet Mask: 255.255.255.240
- Default Gateway: 192.168.20.25

Explicação

Questão 21 de 43

1

Which subnet mask would be appropriate for a network address range to be subnetted for up to eight LANs, with each LAN containing 5 to 26 hosts?

Selecione uma das seguintes:

0.0.0.240
255.255.255.252
255.255.255.0
255.255.255.224
255.255.255.240

Explicação

Questão 22 de 43

1

When a DHCP server is configured, which two IP addresses should never be assignable to hosts? (Choose two.)

Selecione uma ou mais das seguintes:

Network or subnetwork IP address
Broadcast address on the network
P address leased to the LAN
IP address used by the interfaces
Manually assigned address to the clients
Designated IP address to the DHCP server

Explicação

Questão 23 de 43

1

A national retail chain needs to design an IP addressing scheme to support a nationwide network. The company needs a minimum of 300 sub-networks and a maximum of 50 host addresses per subnet. Working with only one Class B address, which of the following subnet masks will support an appropriate addressing scheme? (Choose two.)

Selecione uma ou mais das seguintes:

255.255.255.0
255.255.255.128
255.255.252.0
255.255.255.224
255.255.255.192
255.255.248.0

Explicação

Questão 24 de 43

1

What will happen if a private IP address is assigned to a public interface connected to an ISP?

Selecione uma das seguintes:

Addresses in a private range will be not routed on the Internet backbone.
Only the ISP router will have the capability to access the public network.
The NAT process will be used to translate this address in a valid IP address.
Several automated methods will be necessary on the private network.
A conflict of IP addresses happens, because other public routers can use the same range.

Explicação

Questão 25 de 43

1

Refer to the exhibit.
An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?

Selecione uma das seguintes:

Data link layer
Application layer
Access layer
Session layer
Network layer

Explicação

Questão 26 de 43

1

Refer to the exhibit. A new subnet with 60 hosts has been added to the network. Which subnet address should this network use to provide enough usable addresses while wasting the fewest addresses?

Selecione uma das seguintes:

92.168.1.56/27
192.168.1.64/26
192.168.1.64/27
192.168.1.56/26

Explicação

Questão 27 de 43

1

Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)

Selecione uma ou mais das seguintes:

Network A – 172.16.3.48/26
Network A – 172.16.3.128/25
Network A – 172.16.3.192/26
Link A – 172.16.3.0/30
Link A – 172.16.3.40/30
Link A – 172.16.3.112/30

Explicação

Questão 28 de 43

1

Refer to the exhibit. Which subnet mask will place all hosts on Network B in the same subnet with the least amount of wasted addresses?

Selecione uma das seguintes:

255.255.255.0
255.255.254.0
255.255.252.0
255.255.248.0

Explicação

Questão 29 de 43

1

Refer to the exhibit. What is the most appropriate summarization for these routes?

Selecione uma das seguintes:

10.0.0.0 /21
10.0.0.0 /22
10.0.0.0 /23
10.0.0.0 /24

Explicação

Questão 30 de 43

1

Given an IP address 172.16.28.252 with a subnet mask of 255.255.240.0, what is the correct network address?

Selecione uma das seguintes:

172.16.16.0
172.16.24.0
172.16.0.0
172.16.28.0

Explicação

Questão 31 de 43

1

You are working in a data center environment and are assigned the address range 10.188.31.0/23. You are asked to develop an IP addressing plan to allow the maximum number of subnets with as many as 30 hosts each. Which IP address range meets these requirements?

Selecione uma das seguintes:

10.188.31.0/27
10.188.31.0/26
10.188.31.0/29
10.188.31.0/28
10.188.31.0/25

Explicação

Questão 32 de 43

1

The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?

Selecione uma das seguintes:

8
6
30
32
14
16

Explicação

Questão 33 de 43

1

Refer to the exhibit. The networks connected to router R2 have been summarized as a 192.168.176.0/21 route and sent to R1. Which two packet destination addresses will R1 forward to R2? (Choose two.)

Selecione uma ou mais das seguintes:

192.168.194.160
192.168.183.41
192.168.159.2
192.168.183.255
192.168.179.4
192.168.184.45

Explicação

Questão 34 de 43

1

Refer to the exhibit. What will Router1 do when it receives the data frame shown? (Choose three.)

Selecione uma ou mais das seguintes:

Router1 will strip off the source MAC address and replace it with the MAC address 0000.0c36.6965.
Router1 will strip off the source IP address and replace it with the IP address 192.168.40.1.
Router1 will strip off the destination MAC address and replace it with the MAC address 0000.0c07.4320.
Router1 will strip off the destination IP address and replace it with the IP address of 192.168.40.1.
Router1 will forward the data packet out interface FastEthernet0/1.
Router1 will forward the data packet out interface FastEthernet0/2.

Explicação

Questão 35 de 43

1

Refer to the exhibit. What is the meaning of the output MTU 1500 bytes?

Selecione uma das seguintes:

The maximum number of bytes that can traverse this interface per second is 1500.
The minimum segment size that can traverse this interface is 1500 bytes.
The maximum segment size that can traverse this interface is 1500 bytes.
The minimum packet size that can traverse this interface is 1500 bytes.
The maximum packet size that can traverse this interface is 1500 bytes.
The maximum frame size that can traverse this interface is 1500 bytes.

Explicação

Questão 36 de 43

1

Which command would you use on a Cisco router to verify the Layer 3 path to a host?

Selecione uma das seguintes:

tracert address
traceroute address
telnet address
ssh address

Explicação

Questão 37 de 43

1

Refer to the exhibit.
A network administrator configures a new router and enters the copy startup-config runningconfig command on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem?

Selecione uma das seguintes:

The network administrator failed to save the configuration.
The configuration register is set to 0x2100.
The boot system flash command is missing from the configuration.
The configuration register is set to 0x2102.
The router is configured with the boot system startup command.

Explicação

Questão 38 de 43

1

Refer to the exhibit. What can be determined about the router from the console output?

Selecione uma das seguintes:

No configuration file was found in NVRAM.
No configuration file was found in flash.
No configuration file was found in the PCMCIA card.
Configuration file is normal and will load in 15 seconds.

Explicação

Questão 39 de 43

1

When you are troubleshooting an ACL issue on a router, which command can help you to verify which interfaces are affected by the ACL?

Selecione uma das seguintes:

Show access-lists
Show interface
Show ip interface
Show ip access-lists
List ip interface

Explicação

Questão 40 de 43

1

Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)

Selecione uma ou mais das seguintes:

winipcfg
tracert
ping
ip config
Show ip route
show interfaces

Explicação

Questão 41 de 43

1

Refer to the exhibit.
What is the reason that the interface status is “administratively down, line protocol down”?

Selecione uma das seguintes:

There is no encapsulation type configured.
There is a mismatch in encapsulation types.
The interface is not receiving any keepalives.
The interface has been configured with the shutdown command.
The interface needs to be configured as a DTE device.
The wrong type of cable is connected to the interface.

Explicação

Questão 42 de 43

1

What is a global command?

Selecione uma das seguintes:

a command that is set once and affects the entire router.
a command that is implemented in all foreign and domestic IOS versions.
a command that is universal in application and supports all protocols.
a command that is available in every release of IOS, regardless of the version or deployment status
a command that can be entered in any configuration mode.

Explicação

Questão 43 de 43

1

Which command can you use to manually assign a static IPv6 address to a router interface?

Selecione uma das seguintes:

ipv6 address PREFIX_1::1/64
ipv6 autoconfig 2001:db8:2222:7272::72/64
ipv6 autoconfig
ipv6 address 2001:db8:2222:7272::72/64

	Criado por Diego Arturo Aba aproximadamente 8 anos atrás

Quiz sobre Examen CCNA Certificacion Test, criado por Diego Arturo Aba em 18-04-2016.

Examen CCNA Certificacion Test

Questão 1 de 43

Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that communication?

Selecione uma das seguintes:

Explicação

Questão 2 de 43

A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interface port?

Selecione uma das seguintes:

Explicação

Questão 3 de 43

A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen?

Selecione uma das seguintes:

Explicação

Questão 4 de 43

Which of the following correctly describe steps in the OSI data encapsulation process? (Choose two)

Selecione uma ou mais das seguintes:

Explicação

Questão 5 de 43

Host A is communicating with the server. What will be the source MAC address of the frames received by Host A from the server?

Selecione uma das seguintes:

Explicação

Questão 6 de 43

Refer to the exhibit. What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 7 de 43

For what two purposes does the Ethernet protocol use physical addresses? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 8 de 43

In an Ethernet network, under what two scenarios can devices transmit? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 9 de 43

Which of the following statements describe the network shown in the graphic? What are the proper statements?. (Choose two)

Selecione uma ou mais das seguintes:

Explicação

Questão 10 de 43

How many broadcast domains are shown in the graphic assuming only the default VLAN is configured on the switches?

Selecione uma das seguintes:

Explicação

Questão 11 de 43

What is the first 24 bits in a MAC address called?

Selecione uma das seguintes:

Explicação

Questão 12 de 43

A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation?

Selecione uma das seguintes:

Explicação

Questão 13 de 43

Where does routing occur within the DoD TCP/IP reference model?

Selecione uma das seguintes:

Explicação

Questão 14 de 43

Which statement describes the process of dynamically assigning IP addresses by the DHCP server?

Selecione uma das seguintes:

Explicação

Questão 15 de 43

How does a DHCP server dynamically assign IP addresses to hosts?

Selecione uma das seguintes:

Explicação

Questão 16 de 43

Which two tasks does the Dynamic Host Configuration Protocol perform? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 17 de 43

Which statement is correct regarding the operation of DHCP?

Selecione uma das seguintes:

Explicação

Questão 18 de 43

Refer to the exhibit. Host A pings interface S0/0 on router 3. What is the TTL value for that ping?

Selecione uma das seguintes:

Explicação

Questão 19 de 43

Which command can be used from a PC to verify the connectivity between hosts that connect through a switch in the same LAN?

Selecione uma das seguintes:

Explicação

Questão 20 de 43

Selecione uma das seguintes:

Refer to the exhibit.

What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two.)

Which of the following statements describe the network shown in the graphic?

What are the proper statements?. (Choose two)

A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server.

What is the highest layer of the protocol stack that the network administrator is using for this operation?

Refer to the exhibit.
Host A pings interface S0/0 on router 3. What is the TTL value for that ping?

Refer to the exhibit.
An administrator pings the default gateway at 10.10.10.1 and sees the output as shown. At which OSI layer is the problem?

Refer to the exhibit.
All of the routers in the network are configured with the ip subnet-zero command. Which network addresses should be used for Link A and Network A? (Choose two.)