1837961
Description
Quiz by james crowley, updated more than 1 year ago
|
Created by james crowley
over 9 years ago
|
|
Question 1
Question
1. Flame cleaning is a method of removing:
Answer
-
a. Paint coatings
-
b. Lichen
-
c. Mould
-
d. Rust
Question 2
Question
2. Which of the following would be the most likely cause of saponification?
Answer
-
a. Applying emulsion paint to an alkaline surface
-
b. Applying latex paint to an alkaline surface
-
c. Applying oil-based eggshell to an alkaline surface
-
d. Applying adhesives to an alkaline surface
Question 3
Question
3. Painted timber surfaces should be abraded:
Answer
-
a. With the grain
-
b. Against the grain
-
c. Wet
-
d. None of the above
Question 4
Question
4. What is the name of the defect formed on the surface during the production of steel?
Answer
-
a. Mildew
-
b. Rust
-
c. Mill scale
-
d. Sulphate
Question 5
Question
5. Which of the following does not contribute to corrosion?
Answer
-
a. Water
-
b. Oxygen
-
c. Heat
-
d. Metal
Question 6
Question
6. Which of the following primers is not suitable for use on metal surfaces?
Answer
-
a. ARP
-
b. Zinc phosphate
-
c. MIO
-
d. Etch primer
Question 7
Question
7. The most suitable method of protecting a floor when removing wallpaper using a steam stripper would be:
Answer
-
a. Cotton dust sheets
-
b. Masking tape and paper
-
c. Plastic sheeting
-
d. Tarpaulin
Question 8
Question
8. Which one of the following should not be used in a damp atmosphere?
Answer
-
a. Pneumatic orbital sander
-
b. Liquid petroleum gas
-
c. Electric orbital sander
-
d. Pneumatic needle gun
Question 9
Question
9. A water-based paint applied over silicone bathroom sealant is most likely to result in the defect known as:
Answer
-
a. Crazing
-
b. Flashing
-
c. Orange peel
-
d. Cissing
Question 10
Question
10. ARP would be best suited as a primer coat for:
Answer
-
a. Plaster surfaces to be papered
-
b. Plaster surfaces to be finished in an oil paint
-
c. Plaster surfaces to receive a textured finish
-
d. Plaster surfaces to be finished in matt emulsion
Question 11
Question
11. Which of the following metals requires priming immediately after preparation?
Answer
-
a. Zinc
-
b. Steel
-
c. Lead
-
d. Galvanised steel
Question 12
Question
12. Nail heads protruding from the surface of softwood architraves and skirting boards should be:
Answer
-
a. Punched below the surface, filled and knotted
-
b. Punched below the surface, primed and filled
-
c. Punched level with the surface, stopped up and primed
-
d. Punched below the surface, knotted and filled
Question 13
Question
13. Paint coatings should be completely removed if showing signs of which two defects:
Answer
-
a. Cissing and crazing
-
b. Wrinkling and flashing
-
c. Saponification and grinning
-
d. Crazing and wrinkling
Question 14
Question
14. Painted surfaces can often be affected by mould growths, especially if exposed to which one of the following conditions?
Answer
-
a. Dark areas
-
b. Humidity
-
c. Warmth
-
d. Frost
Question 15
Question
15. The use of an electrical orbital sander at work is covered by which regulations?
Answer
-
a. PUWER
-
b. COSHH
-
c. RIDDOR
-
d. ROSPA
Question 16
Question
16. Which one of the following statements is correct
Answer
-
a. Timber is seasoned to prevent resin exudation
-
b. Timber is seasoned to prevent discoloration
-
c. Timber is seasoned to prevent insect infestation
-
d. Timber is seasoned to prevent warping
Question 17
Question
17. Which two substances can be used to seal knots in timber?
Answer
-
a. Shellac and methylated spirit
-
b. ARP and shellac
-
c. Shellac and aluminium wood primer
-
d. Universal primer and shellac
Question 18
Question
18. Which one of the following is not a cause of bittiness in a finished paint coating?
Answer
-
a. Contaminated application tools
-
b. Atmospheric dust
-
c. Contaminated paint
-
d. Atmospheric moisture
Question 19
Question
19. State the best method of removing contract vinyl wall coverings from a stairwell.
Answer
-
a. Steam stripper and stepladders
-
b. Scaffold, dry stripping and wetting in
-
c. Scaffold and steam stripper
-
d. Ladder, scoring and wetting in
Question 20
Question
20. Which of the following abrasives contains bauxite?
Answer
-
a. Tungsten carbide
-
b. Garnet paper
-
c. Aluminium oxide
-
d. Silicone carbide
Want to create your own Quizzes for free with GoConqr? Learn more.