Avaya - 3100 Test - AUTOEVAL -

DAVID MONTALVA
Quiz by , created about 4 years ago

Quiz on Avaya - 3100 Test - AUTOEVAL -, created by DAVID MONTALVA on 09/09/2015.

25
1
0
Tags
DAVID MONTALVA
Created by DAVID MONTALVA about 4 years ago
AS Sociology - Education Theories
HannahLB
Organic Chemistry
Megan Tarbuck
Narrative/Short Story Writing
Pak Sam
'Love and Relationships' Poem Themes
Lindis Dixon
SDP7 (1) ☉ IITU 2017
Zhandos Ainabek
Chris and Manuel - Girls' and Boys'Education - A Mind Map
manuel_deleon31851
English Grammatical Terminology
Fionnghuala Malone
How to revise
KimberleyC
AS Psychology Unit 1 - Memory
Asterisked
Business Studies Unit 1
emily.mckechnie

Question 1

Question
QUESTION NO: 52 With reference to the Alarm Report shown in the exhibit, which option describes the location of the alarm that occurred on May 13 at 09:25?
Answer
  • cabinet 1, gateway b, media module 12, port 12
  • gateway 1, server b, extension 1212
  • cabinet 1, carrier b, slot 12, port 12
  • server 1, gateway b, media module 12, port 12
  • port network 1, cabinet b, carrier 12, slot 12

Question 2

Question
QUESTION NO: 53 Your Avaya Aura® Communication Manager System has been operating without Incident for several months. Then, one day at 10:00 AM, you get multiple reports about blocked access and users unable to make calls. You run Processor Occupancy Summary and Trunk Group Summary reports and determine that there are no issues with processor occupancy or availability of trunks. So now you decide to see if someone made a change to the system around 10:00 AM Which report will show what administrative or maintenance system changes that were made around 10:00 AM and by whom?
Answer
  • A. A history report
  • B. An activity performed report
  • C. An administrative or maintenance summary report
  • D. A hardware error log report
  • E. A system-parameters change report

Question 3

Question
QUESTION NO: 54 Which trunk type is supported by media module MM710, and circuit packs TN767E, TN464HP, TN2464CP, and TN2207?
Answer
  • A. An IP trunk
  • B. A DSI trunk
  • C. A SIP trunk
  • D. An analog trunk

Question 4

Question
QUESTION NO: 55 Communication Manager and system Platform each have their own backup function and each back up different data. For system Platform based systems, both backups need to be done routinely. What is a difference between the backup function for System Platform and Communication Manager?
Answer
  • A. Only the Communication Manager backup can encrypt the file.
  • B. Only the Communication Manager backup can be scheduled.
  • C. Only the System Platform backup can use secure copy Protocols (SCP).
  • D. Only the System Platform backup can use secure file transfer protocol (SFTP).

Question 5

Question
QUESTION NO: 56 Which feature can you administer using a multi-appearance telephone with Console Permission?
Answer
  • A. Receive Security notifications of Authorization codes violation
  • B. Record integrated Announcements
  • C. Activate and deactivate Coverage paths for another extension
  • D. Add and remove agents from CORs

Question 6

Question
QUESTION NO: 57 You execute the List history command to display the system transaction log. Which two types of Information do you expect to find in the transaction log or history report? (Choose two)
Answer
  • A. valid user logins and logoffs to or from the system
  • B. valid and invalid logins and logoffs to or from the system
  • C. recent, successful administration and maintenance commands to the system
  • D. recent successful and unsuccessful administration and maintenance commands to the system

Question 7

Question
QUESTION NO: 58 Changes that an administrator performs on a system are always only written to ---- RAM. Which SAT command must be used to copy these changes so that the hard disk, so that in case of a loss of power, the changes will be available?
Answer
  • A. Save ------
  • B. Copy running configuration startup configuration
  • C. Copy ------ all
  • D. Save ------ startup configuration

Question 8

Question
QUESTION NO: 59 Through which Communication Manager interface do you add an H.248 gateway to CM?
Answer
  • A. System Access Terminal (SAT)
  • B. System Management Interface (SMI)
  • C. System Platform Management Console
  • D. Linux command line

Question 9

Question
QUESTION NO: 60 With respect to Avaya Aura®, into which two categories does Communication Manager fit? (Choose two.)
Answer
  • A. Architecture
  • B. Communication Services
  • C. Application
  • D. Gateway

Question 10

Question
QUESTION NO: 61 Which ASA main menu option displays the capacity of the Communication Manager?
Answer
  • A. Advanced
  • B. Tasks
  • C. General
  • D. Fault and Performance

Question 11

Question
QUESTION NO: 62 Which component registers SIP Endpoints?
Answer
  • A. System Manager
  • B. Communication Manager
  • C. Switch
  • D. Session Manager

Question 12

Question
QUESTION NO: 63 With respect to a Communication Manager Dial Plan, which command shows Multiple Locations enabled?
Answer
  • A. Display Dial Plan Analysis
  • B. Display System-Parameters Customer Options
  • C. Display Dial Plan Parameters
  • D. Display Customer Options

Question 13

Question
QUESTION NO: 64 You must configure a deportment manager's station so that calls to employees ring even though the called station might have send All Calls activated.
Answer
  • A. Button activated Executive Calling
  • B. FAC or button activated Automatic Inclusion
  • C. FAC or button activated Priority Calling
  • D. Button activated Send All Calls override

Question 14

Question
QUESTION NO: 65 A company is adding a new building to its campus. During construction you receive notice that no one in the Accounting department, which is supported to move the new building when completed, can make an outgoing call. Which Interface and page or command do you use to begin troubleshooting the problem?
Answer
  • A. SMI, Network Configuration page
  • B. SMI, Certificate Alarms page
  • C. List trace command
  • D. SAT, display node-names command

Question 15

Question
Which two main interfaces are used for Communication Manager administration? (Choose two.)
Answer
  • A. IPSI
  • B. SAT
  • C. SMI
  • D. COS

Question 16

Question
QUESTION NO: 67 You are a technician responsible for an Avaya Aura® Communication Manager implementation. You need to connect your PC/laptop to the server for initial setup and administration, as well as, set up a PC/laptop for the customer for on-going administration. From the following list, which method is best used for on-site access to Communication Manager?
Answer
  • A. Through the service PC/laptop connected to the pre-configured CM IP address of 192.11.13.5
  • B. Through the service PC/laptop connected to the services port on the server using a crossover cable
  • C. Through the service PC/laptop connected to the services port on the server using a USB cable
  • D. Through the service PC/laptop connected to the Secure Access Link (SAL) interface on the server using a crossover cable

Question 17

Question
QUESTION NO: 68 When assigning on Abbreviated Dialing Group lists, by which multiple can the list be increased?
Answer
  • A. One
  • B. Three
  • C. Five
  • D. Ten

Question 18

Question
QUESTION NO: 69 Changes performed to Communication Manager are written to volatile RAM. Which Communication Manager SAT command must be used to copy these changes to the hard disk, so that In case of a loss of power, the changes will be available?
Answer
  • A. Save translation
  • B. Copy running-configuration startup-configuration
  • C. Copy translation all
  • D. Save translation startup-configuration

Question 19

Question
QUESTION NO: 70 What is the maximum number of digits allowed for a FAC?
Answer
  • A. 2
  • B. 3
  • C. 4
  • D. 5

Question 20

Question
QUESTION NO: 71 To which two Communication Manager forms are FRLs assigned? (Choose two.)
Answer
  • A. COS
  • B. COR
  • C. Route Pattern
  • D. Station

Question 21

Question
QUESTION NO: 72 AAR is used to route which type of traffic?
Answer
  • A. Internal/Private Network
  • B. External/Public Network
  • C. Public Switched Telephone Network
  • D. Internal and External Networks

Question 22

Question
QUESTION NO: 73 A customer wants to connect two branch offices with an ISDN trunk, where each branch office has a PBX system. Which Service Type should be selected when configuring the trunk?
Answer
  • A. Tie
  • B. Tandem
  • C. Central Office (CO)
  • D. Direct Inward Dial (DID)

Question 23

Question
QUESTION NO: 74 In Communication Manager, which two Interfaces support DS1 trunks? (Choose two.)
Answer
  • A. Circuit Pack
  • B. ISDN/BRI
  • C. Media Module
  • D. Port Network

Question 24

Question
Which Call Coverage feature enables the call to be sent back to the originator?
Answer
  • A. Go To
  • B. Send All Calls
  • C. Consult
  • D. Busy

Question 25

Question
QUESTION NO: 76 When adding an extension, you must conform to which form In Communication Manager?
Answer
  • A. COR
  • B. COS
  • C. Dial Plan
  • D. FAC

Question 26

Question
Refer to the exhibit. Consider the settings shown in the exhibit displayed by using the display route-pattern command. You must deny calls from users in COR 10 to use route pattern 1. To what should the Facility Restriction Level (FRL) for COR 10 be set?
Answer
  • A. 2
  • B. 3
  • C. 4
  • D. 5
  • E. 6

Question 27

Question
QUESTION NO: 78 Which command is needed to verify an Enhanced Call Forwarding destination?
Answer
  • A. Change station xxxx
  • B. Status station xxxx
  • C. Add station xxxx
  • D. Edit station xxxx

Question 28

Question
QUESTION NO: 79 Which two fields and settings must be verified on the system-parameters customer-options form when adding 16xx or 96xx type telephones? (Choose two.)
Answer
  • A. Maximum Concurrently Registered IP Stations greater than "0"
  • B. Maximum Media Gateway VAL Sources greater than "0"
  • C. Maximum Off-PBX Telephones greater than "0"
  • D. IP Stations field is "y"
  • E. Digital Stations field is "y"

Question 29

Question
QUESTION NO: 80 Once the route pattern has been designated for ARS, what is the next step?
Answer
  • A. Choose the AAR
  • B. Choose the FAC
  • C. Choose the network
  • D. Choose the trunk group

Question 30

Question
QUESTION NO: 81 Which users does Call Park best serve?
Answer
  • A. Users who need to retrieve calls from any extension in the system
  • B. Users who travel domestically using smartphones for basic communication
  • C. Users who travel Internationally using smartphones for basic communication
  • D. Users who need to pick up calls from their smartphones while traveling

Question 31

Question
QUESTION NO: 82 Which concept is associated with Terminal Translation Initialization <TTI>?
Answer
  • A. Class of Service (COS)
  • B. Class of Restriction (COR)
  • C. Extension to Cellular (EC)
  • D. Administration without Hardware (AWOH)

Question 32

Question
QUESTION NO: 83 When creating on administrator account, what is the setting In the user profile that allows full access for all commands?
Answer
  • A. r-
  • B. rm
  • C. wm
  • D. rx

Question 33

Question
Which two features are ports of COS? (Choose two.)
Answer
  • A. Data Privacy
  • B. Bridged Call Appearance
  • C. ISDN-PRI
  • D. Console Permissions

Question 34

Question
Which type of traffic does a DID trunk support?
Answer
  • A. Incoming and outgoing calls between the telephone system and the local central office
  • B. Customer-provided equipment to the telephone system
  • C. Incoming calls routed directly to internal extensions
  • D. Outgoing calls between telephone system and the local central office

Question 35

Question
QUESTION NO: 86 What does the Class of Service (COS) setting control? D. The pre-defined features that a user can access and use
Answer
  • A. The applications that a user can access and use
  • B. The capabilities or limits of calling privileges
  • C. The level of service that the user will receive
  • D. The pre-defined features that a user can access and use

Question 36

Question
QUESTION NO: 87 Which statement is true about the Station Lock feature?
Answer
  • A. The feature permits only incoming calls, and using a FAC and security code permits emergency or outgoing calls.
  • B. The feature permits only outgoing calls, and using a FAC and security code permits Incoming and outgoing calls.
  • C. The feature permits Incoming calls, and the telephone can be unlocked only from designated telephone(s) by inputting a security code.
  • D. The feature overrides the COR of a station.

Question 37

Question
QUESTION NO: 88 On the add trunk-group x form, what must match the DAC in the Dial Plan Analysis form?
Answer
  • A. FNPA
  • B. TAC
  • C. COS
  • D. Ext

Question 38

Question
QUESTION NO: 89 Which Call Pickup Group allows the administrator the ability to combine different Pickup Groups?
Answer
  • A. Directed Call Pickup
  • B. Pickup Group
  • C. Expanded Pickup Group
  • D. Extended Pickup Group

Question 39

Question
QUESTION NO: 90 Which signaling protocol registers with Communication Manager?
Answer
  • A. SIP
  • B. H.225
  • C. H.323
  • D. SIP1

Question 40

Question
QUESTION NO: 91 In Communication Manager, in which way are alarms classified?
Answer
  • A. By the number of times the alarms are recorded
  • B. As a function of their effect on the system's operation
  • C. Whether the alarms are on-board or off-board
  • D. By the number of errors that appear

Question 41

Question
QUESTION NO: 92 You execute the list history command. Which type of information do you expect to find in the history report?
Answer
  • A. ASG session establishment/rejection data
  • B. Processor occupancy statistics
  • C. Security violation status summary
  • D. Log Ins/logoffs, administrative and maintenance action commands

Question 42

Question
QUESTION NO: 51 In addition to protocol and function, which two other factors affect the choice of trunk type? (Choose two)
Answer
  • A. number of users
  • B. link bounce timer value
  • C. type of endpoints
  • D. distance
  • E. type of gateways

Question 43

Question
QUESTION NO: 50 Which parameters must be configured to implement Automatic Route Selection (ARS)?
Answer
  • A. Dial Plan, Codec Set, Private Numbering, Network Region
  • B. Far-End Node, Near-End Node, Coverage Path, Call Forwarding
  • C. Feature Access Code, Digit Analysis, Digit Conversion, Route Pattern, Trunk Group
  • D. MGC List, H 2<18 Link Timer, Call Admission Control. Feature Access Code

Question 44

Question
QUESTION NO: 49 A remote user who uses Avaya Softphone to work from home reports that the client (Desktop) application will not register. After verifying that the user has configured the softphone application to “point” to the correct IP address of a communication manager gatekeeper using administered extension, you ask if the user supplied a password when logging on. The user confirms that the password was used on each log-on attempt. You look up the user’s information and note that the type field is 4620 (IP telephone) and the Security Code field is *#*. With referent e to the scenario described in the exhibit, which form will help you diagnose the situation?
Answer
  • A. feature access
  • B. station
  • C. coverage path
  • D. remote access security
  • E. class of service

Question 45

Question
QUESTION NO: 48 Which Communication Manager command creates the most helpful report to diagnose problems with users who, when attempting to place outgoing calls, get reorder tone?
Answer
  • A. List trace station
  • B. List measurement occupancy
  • C. List performance hunt-group
  • D. List measurements call-rate

Question 46

Question
QUESTION NO: 47 A user reports that when attempting to dial an external call to local number the system does nothing – just silence. You interview the user as follows. You: What happens if you longer after you dial your number? User: once I waited for about half a minute, then I heard these tones that supported the something was wrong. You: Did the sound stay on the same pitch or did it change pitches back and forth? User: Back and forth one pitch higher than the other. You: OK, that helps. What did you dial to get an outside line? User: Nine (9) You: Thank you, I appreciate the information, I will get back with you shortly. With reference to the scenario described in the exhibit, which statement most accurately describes the situation?
Answer
  • A. The user should have been able to complete the call as dialed
  • B. The system must be re-administered to correct the situation
  • C. After dialing "9" the user should have dialed more digits, then the external call would have completed
  • D. The user did not dial the correct access code to make an external call

Question 47

Question
QUESTION NO: 46 Which two Fields and Settings must be verified on the system-parameters customer-options form when adding 46xx or 96xx type telephones? (Choose two)
Answer
  • A. Maximum Concurrently Registered IP Stations greater than "0"
  • B. Maximum Media Gateway VAL Sources greater than "0"
  • C. Maximum Off-PBX Telephones greater than "0"
  • D. IP Stations field in "y"
  • E. Digital Stations field In "y"

Question 48

Question
QUESTION NO: 45 You are a technician responsible for an Avaya Aura® Communication Manager Implementation and you need to connect your PC/laptop to the server for Initial setup and administration, as well as setup a PC/laptop for the customer to do on-going administration. Which two methods are available for on-site access to the Communication Manager server? (Choose two.)
Answer
  • A. through any PC on the customer's LAN connecting to the predefined, static IP addresses for the communication server or the service PC
  • B. through the service PC/laptop connected to the services port on the communication server using a crossover cable
  • C. through the service PC/laptop connected to the services port on the communication server using a USB cable
  • D. through the service PC/laptop connected to the SAL (secure access link) interface on the communication server using a crossover cable

Question 49

Question
QUESTION NO: 44 The monitor and display capacity commands can be sued to get a real-time status of the system using Avaya Site Administration (ASA). Which command and tool should you use to view the current load for a specific trunk group?
Answer
  • A. monitor load command using terminal emulation
  • B. monitor traffic command using terminal emulation
  • C. monitor traffic command using GEDI
  • D. display capacity using GEDI or terminal emulation

Question 50

Question
QUESTION NO: 43 System functionality for a user is controlled by accessing one of the 16 class of service (COS) settings. What does the COS settings control?
Answer
  • A. the applications that a user can access and use
  • B. the capabilities or limits of calling privileges
  • C. the level of service that the user will get during peak usage time
  • D. the optional features that a user can access and use

Question 51

Question
Consider the ARS Digit Conversion Table and ARS Digit Analysis Table shown in the exhibit. A user dials the sequence 9602323501 in a system where the number 9 is assigned to Automatic Route Selection (ARS) FAC. What Route Pattern will route the call?
Answer
  • A. Route Pattern 1
  • B. Route Pattern 2
  • C. Route Pattern 3
  • D. Route Pattern 4

Question 52

Question
QUESTION NO: 41 When adding an IP Station type 96xx, which statement is true regarding the port field?
Answer
  • A. It is automatically populated by the system as “IP”.
  • B. It must be populated as "SOOOXX"
  • C. It must be populated with an available port on an MM712 or TN2214
  • D. It must be populated with an available port on the LAN switch.

Question 53

Question
QUESTION NO: 40 You must add 500 new stations with a four digit length, starting with station 4500. What information must you populate in the dial plan analysis form?
Answer
  • A. Dialed String = 4; Total Length =4; Call type = sta
  • B. Dialed String = 45; Total Length =4; Call type = ext
  • C. Dialed String = 4; Total Length =4; Call type = ext
  • D. Dialed String = 45; Total Length =4; Call type = sta

Question 54

Question
QUESTION NO: 39 A customer wants to connect two branch offices with an ISDN trunk, where each branch office has a PBX system. Which service Type Should you selected in the configuration of the trunk?
Answer
  • A. Tie
  • B. Tandem
  • C. Operator
  • D. Internal

Question 55

Question
QUESTION NO: 1 There are two GUI-based access tools available: Avaya site administration (ASA) and system management interface (SMI). Which statement correctly differentiates between ASA and SMI?
Answer
  • A. Both SMI and ASA can perform the same administration tasks but ASA is being replaced by SMI.
  • B. Both SMI and ASA can perform the same administration tasks but SMI is for technicians and ASA is for customers.
  • C. SMI provides access to less frequent administration, installation and upgrade functions, while ASA provides access to day-to-day administration functions.
  • D. Old hardware and software (Pre – 5.x) is administered using SMI, while current hardware and software (5.x and later) is administered using ASA.

Question 56

Question
QUESTION NO: 2 Consider the signaling Group Information shown in the exhibit. Which SAT command can you use to get the IP address of the Far-end Node of the Signaling group 50?
Answer
  • A. Display board CLAN10
  • B. List node-name all
  • C. List ip-address nodes
  • D. List ip-interface nodes

Question 57

Question
QUESTION NO: 3 Communication Manager Backups are done through the system management interface (SMI). Which three statements about the Communication Manager backup function are correct? (Choose three)
Answer
  • A. The backup function creates two complete files on the internal hardware drive.
  • B. The backup function can create a file on a network device using protocols: SCP, SFTP, or FTP.
  • C. The backup function can encrypt the file with a pass phrase.
  • D. The backup is done dynamically and cannot be scheduled in advance.
  • E. The full Backup option does not do Save Transaction Command Automatically before creating the backup file.

Question 58

Question
QUESTION NO: 4 You are adding ten new IP telephones in a small company administered with a G430 Media Gateway and a S8300D ICC main server. The G430 has the S8300D inserted in the slot V1, and MM710 in the slot V2, and an MM712 in the slot V3. Which hardware module will act as Gatekeeper for the telephones?
Answer
  • A. MM710
  • B. MM712
  • C. MGP on the media gateway
  • D. S8300D server using Processor Ethernet (PE)

Question 59

Question
QUESTION NO: 5 The Avaya Extension to Cellular feature provides users with the capability to have one administered telephone that supports communication manager features for both an office telephone and one outside cellular or wireless telephone, two fields must be set to “Yes” in order to use this functionality: Enhanced EC500 and extended Cvg/Fwd Admin. Which command do you use to verify the field settings?
Answer
  • A. System-parameters features
  • B. System-parameters customer-options
  • C. System-parameters wireless
  • D. System-parameters converge-forwarding

Question 60

Question
QUESTION NO: 6 A remote user Avaya softphone to work from home reports that the client desktop application will not register. After verifying that the user has configured the softphone application to “point” to the current IP address of a Communication Manager Gatekeeper using an administered extension, you ask if the user supplied a password when logging on. The user confirms that the password was used on each log-on attempt. You look up the user’s information and note that the type field is 4620 (IP telephone) and the security code field is. With reference to the scenario described in the exhibit, which action should you take to ensure that the user can use the IP SoftPhone?
Answer
  • A. Change the IP SoftPhone field to y.
  • B. Change the Converge Path 1 value to match the value in converge path 2.
  • C. Change the message Lamp Ext value to match the extension number.
  • D. Change the name in the name field to match the name as administered in the LDAP directory

Question 61

Question
QUESTION NO: 7 You want a user’s station to be able to dial extension 5605 and 5608 only. Which station configuration will achieve this?
Answer
  • A. Assign COR 11 to user’ station, In COR11 Set COR-to COR calling permission = ‘n’ for all except COR 10. Assign COR to 5605 and 5608. Ensure that these two CORs are not assigned to any other station object.
  • B. The FRL = 7to user’s station. FRL = 7 to station 5606 and 5608. Set FRL for all other stations to 6 and lesser
  • C. Assign COR 10 to user’s station. In COR 11, set CPR-to-COR calling permission = ‘n’ for all except. Assign COR 11 to 5605 and 5608. Ensure that these two CORs are not assigned to any other object.
  • D. The FRL = 5 to user’s station, FRL = 7 to station 5606 and 5608. Set FRL for all other stations to 5 or lesser.

Question 62

Question
QUESTION NO: 8 With reference to the Dial Plan Analysis Tables, how many codes are available in the system for activation / deactivation of features?
Answer
  • A. 2
  • B. 3
  • C. 11
  • D. 21

Question 63

Question
QUESTION NO: 9 You have to add a new G650 Media Gateway to the system. Which command will perform this I
Answer
  • A. add cabinet next
  • B. add port network next
  • C. add media – gateway next
  • D. add G6SO-port next.

Question 64

Question
QUESTION NO: 10 Although not exactly the same, a bridged call appearance and a team button can perform some of the same functions. Which statement correctly contrasts the team button and bridged call appearance?
Answer
  • A. The team button does not allow conferencing to an active call or speed dial to the monitored station.
  • B. The team button allows conferencing to an active call and making outgoing calls for the monitored station.
  • C. The bridged call appearance does not allow conferencing to an active call or speed dial to the mirrored station.
  • D. The bridged call appearance allows conferencing to an active call and making outgoing calls for the mirrored station.

Question 65

Question
QUESTION NO: 11 You need to configure a station so that when a department manager makes calls to employees the manager's calls will ring even though the called station might have Sent All Calls activated. Although the manager's station can be designated as a VIP telephone, the manger must be able to selectively activate this feature. Which feature addresses this need?
Answer
  • A. Button activated Executive Calling
  • B. FAC or button activated Automatic Inclusion
  • C. FAC or button activated Priority Calling
  • D. Button activated Send All Calls override

Question 66

Question
QUESTION NO: 12 Your customer has a communication Manager 6.0 branch location with SIP endpoints that need to survive a WAN failure when communication to the core or main Session Manager is unavailable. Which solution will provide survivability to the remote location?
Answer
  • A. an S8300 configured as an local survivable processor (LSP)
  • B. a simplex server configured as an enterprise survivable server (ESS)
  • C. an S8300 or simplex server configured as a Survivable Remote
  • D. an S8300 01 simplex server configured for high availability (HA)

Question 67

Question
QUESTION NO: 13 Consider the settings shown in exhibit displayed by using the display route – pattern command. You must deny calls from users in COR 10 to use route pattern 1. What should the fault restriction level (FRL) for COR 10 be?
Answer
  • A. 2
  • B. 3
  • C. 4
  • D. 5
  • E. 6

Question 68

Question
QUESTION NO: 14 With reference to the list trace station 1101 printout shown in the exhibit, what statement describes what happened during the time period of the trace?
Answer
  • A. Station 1101 called station, hung-up and finally called station 100.
  • B. Station 1101 called station 1000, the unanswered call went to the voicemail, and finally station 1101 called 1001.
  • C. Station 1101 called station 1000, and the station answered, then station 1000 transferred to call to station 1001.
  • D. Station 1101 called station 1000, unanswered; the call covered the station 1001

Question 69

Question
QUESTION NO: 15 You are configuring Personal Station Access (PSA) and you configure the Communication Manager with the following settings: - Set TTI enabled = ‘Y’ - Set PSA Associated code = ‘25’ and disassociate code ‘#25’ - Set security code for the station = ‘1234’ You activate the station by keying in FAC for PSA, station extension number, ‘#’, the security code of the station, and ‘#’. However, the station is not activated. Which statement describes the issue to be addressed?
Answer
  • A. You need to set TTI = ‘n’
  • B. You did not enable PSA on the COS of the station.
  • C. You should not set the security code in sequential order.
  • D. You did not key in the correct activation sequence

Question 70

Question
QUESTION NO: 16 Which statement most accurately describes the major difference between Automatic Alternative Rom (AAR) and Automatic Route Selection (ARS) in a typical installation?
Answer
  • A. AAR routes calls over a public network; ARS routes calls over a private network.
  • B. AAR routes calls over a private network; ARS routes calls over a public network.
  • C. AAR chooses routes automatically; ARS chooses routes according to pre programmed, bestchoice parameters.
  • D. AAR chooses routes automatically; ARS chooses routes according to a manually administered route plan.

Question 71

Question
QUESTION NO: 17 The monitor and display capacity commands can be used to get a real-time status of the system using Avaya Site Administration (ASA). Which command and tool should you use to view a summary of the overall condition of the system?
Answer
  • A. Monitor system command using terminal emulation mode
  • B. Monitor system command using GEDI
  • C. Monitor status command using terminal emulation mode
  • D. Display status using GEPI or terminal emulation mode

Question 72

Question
QUESTION NO: 18 Which setting in the system parameter feature screen will enable TTI to be applicable to both analog and digital stations?
Answer
  • A. Terminal Trans. Init.? Y, TTI state = ‘voice’, TTI enable = ‘y’, TTI security code = ‘1709’, CTI enabled = ‘n’.
  • B. Terminal Trans. Init.? Y, TTI state = ‘data’, TTI enable = ‘y’, TTI security code = ‘1709’, CTI enabled = ‘y’.
  • C. Terminal Trans. Init.? Y, TTI state = ‘vdata’, TTI enable = ‘y’, TTI security code = ‘1709’, CTI enabled = ‘n’.
  • D. Terminal Trans. Init.? Y, TTI state = ‘voice’, TTI enable = ‘y’, TTI security code = ‘1709’, CTI enabled = ‘y’.

Question 73

Question
QUESTION NO: 19 Which user’s does Call Park best serve?
Answer
  • A. users who travel domestically using smartphones for basic communication
  • B. users who need to pick up calls from any extension In the system when the call Is placed on hold
  • C. users who travel internationally using smartphones for basic communication
  • D. users who need to pick up calls from their smartphones while traveling

Question 74

Question
QUESTION NO: 20 Which statement most accurately describes the function of automatic call back feature?
Answer
  • A. It allows internal users who placed a call to a busy or unanswered external telephone to be called back when the called telephone becomes available.
  • B. It allows internal users who placed a call to a busy or unanswered internal telephone to be called back when the called telephone becomes available.
  • C. It allows internal users who are called when they are busy to activate a feature to automatically call back that second caller, once the first call is finished.
  • D. It allows internal users who are called when they are busy to place the second call on hold until the first call is finished.

Question 75

Question
QUESTION NO: 21 Which two Statements are true about Automatic Route Selection (ARS)? (Choose two)
Answer
  • A. ARS routes calls only across tie trunks to local switching equipment.
  • B. ARS routes calls to remote company locations in the absence of a private network.
  • C. ARS allows Communication Manager to use an ISDN trunk to connect to the PSTN.
  • D. ARS mutes calls across all trunk types but only to remote switching equipment

Question 76

Question
QUESTION NO: 22 Your customer wants to extend their office calls using the Extension to Cellular features. Where will calls be redirected?
Answer
  • A. To another extension on the same system
  • B. To a hunt group
  • C. To an administered off-system number
  • D. To a call pickup group

Question 77

Question
QUESTION NO: 23 The station lock feature manually or automatically changes the COR of a station to block outgoing calls recently, extensions at a customer’s site have been used for out of hours outgoing calls. IT would like to activate this feature automatically on the telephone on site. To address safety concerns, what do you tell the site manager regarding outgoing emergency calls and incoming or outgoing calls if staff needs to work overtime?
Answer
  • A. The station lock feature does not block incoming calls and using a code they can make emergency or outgoing calls.
  • B. The station lock features does not block outgoing emergency calls and using a code they can receive incoming calls and make outgoing calls.
  • C. The station lock feature does not block incoming calls or emergency outgoing calls and the telephone can be unlocked from designated telephone(s) by inputting a code.
  • D. The station lock feature does not block incoming calls or emergency outgoing calls and the telephone can be unlocked by inputting a code.

Question 78

Question
QUESTION NO: 24 You run a daily Occupancy Summary Measurements report to monitor system capacity and to review processor occupancy metrics. Which occupancy situation is an issue that warrants further analysis?
Answer
  • A. For two nonconsecutive hours, the idle Occ value was between 20 and 25 pervent.
  • B. For one hour, the combined SM Occ and idle Occ was 90 percent.
  • C. For two consecutive hours, the Static Occ and SM Occ were each below 10 percent.
  • D. For two consecutive hours, the combined Static Occ and CP occ was 77 percent

Question 79

Question
QUESTION NO: 25 You are creating a new ISDN bunk group in a production system and you want to know the capacity and features that are enabled in the installed license file of the system. Which command will provide this information?
Answer
  • A. system -parameters capacity
  • B. system-parameters customer-options
  • C. system -parameters features
  • D. system-parameters customer-license

Question 80

Question
QUESTION NO: 26 You are preparing to configuration the system to perform an automatic daily full backup to external storage medium. What Information must you know about HIP FTP server to program the backup?
Answer
  • A. IP address, port number, and default directory
  • B. User name, password, IP address, and default directory
  • C. User name, password, and default directory
  • D. IP address, port number, protocol, and default directory

Question 81

Question
QUESTION NO: 27 With consideration to the exhibit, in which hardware component do you configure the IP address 150.122 44 210?
Answer
  • A. In the Media Gateway
  • B. In the Server administration port
  • C. In a CLAN board or Processor Ethernet port
  • D. In the Server services port

Question 82

Question
You are adding five new digital stations in a branch office where there is a G450 media Gateway. On which media Module do you look for available ports?
Answer
  • A. MM717
  • B. MM711
  • C. MM712
  • D. MM714

Question 83

Question
QUESTION NO: 29 Administrative users are assigned a user profile that specifies both a web profile group and a SAT profile group. This controls the functions a user can perform with SAT and within the system Management Interface (SMI). How does the SAT profile control the functions?
Answer
  • A. It controls the SAT “action” commands the user can use.
  • B. It controls the time of day that the user can do Sat administration.
  • C. It controls which SAT screens or categories the user can access.
  • D. It controls the type of SAT access (GEDI or terminal emulation) the user can use.

Question 84

Question
QUESTION NO: 30 Your customer had a short WAN outage and you want to know If all of the gateways have reregistered with the Communication Manager server. Which Interface and command must be used?
Answer
  • A. ASA with a display process-status command
  • B. SMI with a process status command
  • C. SMI with a status summary command
  • D. ASA with a status media-gateway command

Question 85

Question
All release ox and later Avaya Aura® Communication Manager (CM) deployments support secure link access: SAL for remote access to the server and alarm notification from the server to the support engineer? Which hardware or software is required at the customer site for SAL support of the CM server?
Answer
  • A. SAL software is required and uses a separate SAL server.
  • B. SAL software is required and uses a secure external modem.
  • C. SAL software is part of System Platform and requires no additional hardware.
  • D. SAL software is part of System Platform and uses a remote maintenance board (RMB) that must be installed in the server.

Question 86

Question
QUESTION NO: 32 Security Violation show valid and invalid attempts to access the system using three types of codes. In addition to station security codes, which two types of codes are measured in security Violation reports? (Choose two)
Answer
  • A. Barrier codes
  • B. Access security gateway (ASG) codes
  • C. Dial access codes (DAC)
  • D. Authorization codes
  • E. Administrative login codes

Question 87

Question
QUESTION NO: 33 For which purpose is Automatic Alternate Routing (AAR) used?
Answer
  • A. Calls placed within a company over a public network
  • B. Calls placed within a company over a private network
  • C. Calls placed from outside a company over a private network
  • D. Calls placed from outside a company over a public network

Question 88

Question
QUESTION NO: 34 Which command must be used to define the system internal number scheme of the extensions?
Answer
  • A. Change diaplan parameters
  • B. Change node-name IP
  • C. Change dialplan analysis
  • D. Change uniform-dialplan

Question 89

Question
QUESTION NO: 35 Your customer does not use an AAA server. You have been asked to add four new administrative users with a new user profile that has display only access and no maintenance for the same categories as profile 20. Which interface must be used?
Answer
  • A. ASA with GED1
  • B. ASA with terminal emulation
  • C. SMI
  • D. SMI or ASA

Question 90

Question
QUESTION NO: 36 A user reports that when attempting to dial an external call to local number the system does nothing – just silence. You interview the user as follows. You: What happens if you longer after you dial your number? User: once I waited for about half a minute, then I heard these tones that supported the something was wrong. You: Did the sound stay on the same pitch or did it change pitches back and forth? User: Back and forth one pitch higher than the other. You: OK, that helps. What did you dial to get an outside line? User: Nine (9) You: Thank you, I appreciate the information, I will get back with you shortly With reference to the scenario shown in the exhibit, which action should you take?
Answer
  • A. Re-administer the Dial Plan to requiring 10 digits for making local external calls
  • B. Determine the correct Feature Access Code to make an external call and inform the user
  • C. Re-administer the feature access code for the user’s situation to dial ‘9’ to make an external call.
  • D. Do nothing to the Dial Plan but delete the “*” Feature Access Code

Question 91

Question
QUESTION NO: 37 You must set the calling privileges for a user so that the user can make calls but not receive calls. You assign COR 5 to the user’s station. What other settings must be completed?
Answer
  • A. In COR 5, set calling party restriction = ‘origination’ and called party restriction = ‘none’
  • B. In COR 5, set calling party restriction = ‘outward’ and called party restriction = ‘termination’
  • C. In COR 5, set calling party restriction = ‘origination’ and called party restriction = ‘termination’
  • D. In COR 5, set calling party restriction = ‘none’ and called party restrictions = ‘termination’

Question 92

Question
QUESTION NO: 38 You must verify in a production system that the number of rings between each point for coverage paths is two rings. You access the system-parameters coverage-forwarding from and check that the value for the local coverage Subsequent Redirection/ CFWD No Answer interval field is set to 2. Which users will be affected by this setting?
Answer
  • A. users belonging to a specific COR
  • B. users belonging to a specific COS
  • C. users belonging to a specific COS-group
  • D. all users in the system