CCNA 3 v5.03 Chapter 2

Description

sophomore CCNA 3 Quiz on CCNA 3 v5.03 Chapter 2, created by Christina Evans on 15/06/2016.
Christina Evans
Quiz by Christina Evans, updated more than 1 year ago
Christina Evans
Created by Christina Evans almost 8 years ago
59
1

Resource summary

Question 1

Question
What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active alternative physical paths?
Answer
  • Frame collisions increase.
  • The number of broadcast domains increases.
  • Application protocols malfunction.
  • The number of collision domains increases.

Question 2

Question
What additional information is contained in the 12-bit extended system ID of a BPDU?
Answer
  • MAC address
  • VLAN ID
  • IP address
  • port ID

Question 3

Question
Which three components are combined to form a bridge ID?
Answer
  • port ID
  • IP address
  • extended system ID
  • MAC address
  • bridge priority
  • cost

Question 4

Question
Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?
Answer
  • Trunk1
  • Trunk2
  • Trunk3
  • Trunk4

Question 5

Question
Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?
Answer
  • designated port
  • root port
  • alternate
  • disabled port

Question 6

Question
Which is the default STP operation mode on Cisco Catalyst switches?
Answer
  • RSTP
  • PVST+
  • MST
  • MSTP
  • Rapid PVST+

Question 7

Question
What is an advantage of PVST+?
Answer
  • PVST+ requires fewer CPU cycles for all the switches in the network.
  • PVST+ reduces bandwidth consumption compared to traditional implementations of STP that use CST.
  • PVST+ optimizes performance on the network through autoselection of the root bridge.
  • PVST+ optimizes performance on the network through load sharing.

Question 8

Question
In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)
Answer
  • blocking
  • disabled
  • forwarding
  • learning
  • listening

Question 9

Question
Which STP priority configuration would ensure that a switch would always be the root switch?
Answer
  • spanning-tree vlan 10 priority 0
  • spanning-tree vlan 10 priority 61440
  • spanning-tree vlan 10 root primary
  • spanning-tree vlan 10 priority 4096

Question 10

Question
To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)
Answer
  • The root bridge BID.
  • The role of the ports in all VLANs.
  • The status of native VLAN ports
  • The number of broadcasts received on each root port.
  • The IP address of the management VLAN interface.

Question 11

Question
Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)
Answer
  • static default routes
  • implementing VLANs to contain broadcasts
  • redundant links between Layer 2 switches
  • link-state dynamic routing that provides redundant routes
  • removing single points of failure with multiple Layer 2 switches

Question 12

Question
Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?
Answer
  • HSRP
  • VRRPv2
  • GLBP
  • SLB

Question 13

Question
Refer to the exhibit. Which protocol information is being displayed in the output?
Answer
  • FHRP
  • GLBP
  • HSRP
  • VRRP

Question 14

Question
Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?
Answer
  • 192.168.2.0
  • 192.168.2.1
  • 192.168.2.2
  • 192.168.2.100

Question 15

Question
What value determines the root bridge when all switches connected by trunk links have default STP configurations?
Answer
  • VLAN ID
  • MAC address
  • extended system ID
  • bridge priority

Question 16

Question
Which two concepts relate to a switch port that is intended to have only end devices attached and intended never to be used to connect to another switch? (Choose two.)
Answer
  • bridge ID
  • edge port
  • extended system ID
  • PortFast
  • PVST+

Question 17

Question
Which Cisco switch feature ensures that configured switch edge ports do not cause Layer 2 loops if a port is mistakenly connected to another switch?
Answer
  • BPDU guard
  • extended system ID
  • PortFast
  • PVST+

Question 18

Question
Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby brief command on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?
Answer
  • the IP address and the MAC address of R1
  • the virtual IP address and the virtual MAC address for the HSRP group 1
  • the virtual IP address of the HSRP group 1 and the MAC address of R1
  • the virtual IP address of the HSRP group 1 and the MAC address of R2

Question 19

Question
Fill in the blank. Do not abbreviate. To enable Rapid PVST+ on a Cisco switch, the spanning-tree mode [blank_start]rapid-pvst[blank_end] global configuration mode command is required
Answer
  • rapid-pvst

Question 20

Question
Fill in the blank. Use a number. The default hello timer value for STP BPDU frames is [blank_start]2[blank_end] seconds.
Answer
  • 2

Question 21

Question
Fill in the blank. In FHRP operation, two or more routers are represented as a single [blank_start]virtual[blank_end] router.
Answer
  • virtual

Question 22

Question
Match the spanning-tree feature with the protocol type. (Not all options are used.)
Answer
  • Cisco implement IEEE 802 1D
  • Fast converging enhancement IEEE 802 1D
  • IEEE standard that reduces number of STP
  • Propietary VLAN IEEE 802 1w

Question 23

Question
Match the step number to the sequence of stages that occur during the HSRP failover process.
Answer
  • _______________Step 1________________
  • _______________Step 2________________
  • _______________Step 3________________
  • _______________Step 4________________

Question 24

Question
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which switch is the root bridge?
Answer
  • Switch_1
  • Switch_2
  • Switch_3
  • Switch_4
Show full summary Hide full summary

Similar

CCNA 3v5.03 Chapter 3
Christina Evans
SB&W: Exam CH 7 & 8
Anthony Schulmeister
CCNA 3 v5.03 Chapter 5
Christina Evans
Final Exam (Objective): CH 1-9
Anthony Schulmeister
CCNA 3v5.03 Chapter 4
Christina Evans
CCNA 3v5.03 Chapter 6
Christina Evans
CCNA 3v5.03 Chapter 7
Christina Evans
Biology Unit 1
anna.mat1997
Respiratory System
Addeana
GCSE REVISION TIMETABLE
gracemiddleton
The Tempest
Dirk Weibye