Quiz
CIVIL 3D
Erstelle ein kostenloses Konto, um dieses Quiz zu beenden
Speichere deinen Fortschritt und sieh dir dein Endergebnis an.
oder mit deiner E-Mail registrieren
Schon ein Konto? Anmelden
Fragen in diesem Quiz (32)
1Open CodeSetLabel.dwg
Use the Offset Evaluation Section View label style of standard what is the elevation of the bottom right edge of the median ditch at station 2+50?
(Display as shown within the label style)- A627.09
- B627.08
- C627.1
2Open the drawing AlignmentGeometry.dwg
Add atangent line from the end of curve number 2. the line should have a length of 718.656
What is the end station of the alignment as displayed?
- A19+72.94
- B19+74.94
- C19+7.94
3Open SurfaceCharacteristics.dwg
Note: if you get a massage about rebuild the surface in the drawing, it can be ignored. the surface does not need to be rebuilt
Add a boundary to the surface by using the red polyline. Accept all default.
What is the MEAN elevation of the surface?
(As shown within the surface properties)- A693.34
- B692.34
- C63.34
4Open Annotate Surface.dwg
Using the Contour - Multiple label Type, Annotate the contour lines between the circle labeled a and the circle labeled B
What is the elevation diference between the first and last labeled contour?
(Use a precision as displayed on screen (0.00))- A6.15
- B6.16
- C61.5
5Open ParcelStyles2. dwg
*Create a parcel area label style that displays the acreage and parcel number.
*Apply the new parcel area label style to the lot parcels.
*Renumber all the parvels (excluiding the cul-de-sac), in clockwise order stating at parcel 131. the parcel renumbering shall at number 100.
What is the parcel number of the parcel with the largest area (excluiding the cul-de-sac)?- A108
- B109
- C108.9
6Open ImportPoints.dwg.
Import the piont file named Import PENZD spaced.txt.
What is the full description of point number 235?- ADMH
- BHMD
- CHDM
7Open ProfileLayout.dwg
Create a design profile using the following criteria, shown in the image
Note: Vertical curves should be parabolic.
What is the elevation of profile at station 12+00?
(Provide your answer with a precision of 0.001)
- A702.069 feet
- B702.09 feet
- C702.06 feet
8open SurfaceProfile.dwg
Add and Offset Surface profile from the EG surface base upon the following criterion: the profile is 25 feet offset to the left using a profile view label, what is the elevation of the offset profile at station 12+00?
(As Shown on screen)- A673.17
- B671.17
- C679.17
9Open parcelStyles.dwg.
Wht is the name of the style that would be used to display the roadway as shown on the exhibit?
- ARoad(Local)
- BRoad(Exterior)
- CRoad(Parcel)
10Open CreateSurface.dwg.
*Create a new surface named Composite.
*past the EG surface in, Followed by the proposed surface.
*raise the EG surface 1.2 feet.
*Ensure that the surface is rebuilt
What is the mean elevation for the Cosposite surface?
(As show within the surface properties)- A96.71 feet
- B93.71 feet
- C90.71 feet
11Open DataShortcuts.dwg.
*Set up the working folders and data shorcut in the following objects (Working folders may be placed anywhere, associate drawings to project as needed):
-EG surface from the DataSurface drawing.
-Ridge road alignmet from the DataAlignmentProfile drawing
-Ridge Road-Layout profile from the DataAlignmentProfile drawing
*Using the stationOffsetProfile label style, label the Ridge road aligment at station 16+00 with NO offset Value (or 0)
What is the profile elevation data as displayed?- A699.861
- B692.861
- C699.851
12Open SurfaceVolumes.dwg
*Create a TIN volume surface that has EG as the base and top as the comparation surface. the style should be 2D elevation.
*Sate the elevation analysis to the following:
-Range internal with datum:1
-Datum elevation:0
*Add a surface elevations legend table.
What is the 2D area for range ID 10?
(As Shown within the table)- A4700.89 square feet
- B4750.19 square feet
- C4720.86 square feet
13Open transparencyCommands.dwg.
*Begin the Polyline command.
*Use the Point Number Transparency command to draw a polyline sequentially from point 1 through point 10.
*Close the polyline
What is the length of the polyline?
(As shown in the properties palette- A726
- B627
- C726.5
14Open Code setStyle.dwg
Based upon the exhibit shown, which Code set style is used to display the assembly this way?
- AView-Edit
- BView-modify
- CView-correct
15Open CreateProfileView.dwg
*Edit the Standard profile view style and make the profile vertcal scale 1 inch=5 feet
*Create a profile view containing a surface profile of EG and the proposed layout profile. Use the automatic settings for station range and profile view height
*place the profile view at the center of circle A.
using a station and elevetation label to get the data, what is the elevation at the center of circle B?
(Uae the precision as shown in the label styles (0.00))- A675.21
- B657.21
- C756.21
16Open corridorCreation.dwg.
*Create a corridor using the alignment, layout profile, and assembly provided in the drawing.
*Configure the corridor so that the daylight sub-assemblies tie into the surface in the drawing.
Using the ID Command. What is the elevation of the right daylight point at station 12+00?
(Display as shown within your command line)- A738.133
- B781.133
- C7333.183
17Open PointGroups.dwg
*For the _All points point group, override the point style and point label style to be none.
*Create a point group that includes all point with the full description TMH
*Override the label style to just elevation and description for all points within the new group.
wht is the elevation displayd for the easternmost point within the rectangle?
(As Displayed on screen)- A88.628
- B880.628
- C886.28
18Open ProfileViewStyle.dwg.
Change the vertical exaggeration of the OakRoad profile view to 5.
What is the elevation of yellow polyline shown in the drawing?- A590.1
- B590
- C591.0
19Open Grading.dwg.
Create a grsding design for thr psrking lot outline based on the exhibit provided and the following design parameters.
*Do NOT weed feature lines or grading if asked.
*Create a festure line from polyline using the RED polyline assign it to parking Lot site. erase existing entities and Assign elevations.
*Use the surface named 2% slope to assign elevation to the feature line representing the outiline of the pasrking lot. Verify that insert intermediate grade break points is selected.
*as a result, the feature line should be at elevation 100.00 at the location shown, and slope southward at 2%.
*the edges of the parking lot should be tied to the XG surface using cut and fill slopes of 3:1
Create and infill for the interior of the parking Lot.
What is the FILL value resulting from this analysis?
(As displayed in the grading volume tools or the surface volume)
- A4813.6 cubic yards
- B4818.6 cubic yards
- C481.36 cubic yards
20Open SurfaceSlopes.dwg.
Perform a Slope amalysis using the following ranges:
*0%-5%
*5%-10%
*10%-15%
15%-20%
20%-25%
25%-Maximum Slope
Create a legend for the slope data that you have generated. based on the legend, what is the area of the 0%-5% range?
(As shown within the table)- A25448.27
- B254.4827
- C2548.27
21Open CreateSectionViews.dwg.
Creater section sheets using the view group already in the drawing using the following criterai:
*From the create section sheets wizard, confirm that centerline (1) is the alignment, that SLG-1 is the sample line group name, and that section View Group - 1 is the section view group.
*All other settings to be left as default settings.
What is the layout name of the layout that contains the section view for station 16+50?- ASection Sheet - (25)
- BSection Sheet - (20)
- CSection Sheet - (15)
22Open CreatePoint.dwg
*Using the Create Point tool, create 26 points by diving the alignment into 25 equal parts.
*Offset the points to the left of the alignment 50 feet.
*Elevate the points to the EG surface.
What is the elevation displayd for the point closest to station 10+00?
(As displayed on screen)- A694.44
- B695.44
- C694.34
23Open SurfaceFromPoints.dwg.
*Create a Surface called EG_Topo.
*Use the Style named Contours 1´ and 5´(Background).
*Add the Point group EG_Topo to the surface?
(As Shown within the surface properties)- A120.7
- B127.0
- C121.70
24Open SpotElevationLabelStyle.dwg.
Use a Spot Elevation label to label the nodo.
Which label style output matches the image?
- ALabel3
- BLabel5
- CLabel4
25Open Interference.dwg.
*create a pipe network with the following criteria:
-Network Parts List: Sanitary
-Surface: EG and FG
-Sutructure Label: structure name
-Pipe label: pipe name
-Laying out from downstream to upstream
*Using the concentric Manhole and 8-inch PVC pipe, lay out the system from the center of circles A through G.
*Create an interference check between storm and sanitary using the default settings. Ensure 3D Proximity is set to use a distance of 8´
What is the name of the sanitary sewer pipe that conflicts whith the storm network part?- ASS-(7)
- BSS-(9)
- CSS-(5)
26Open GradingFeatureLines.dwg
Using the feature line alredy created in the FL_Grading Site, Grade site the following criteria:
*Create a new grading group.
*Daylinght to EG surface from at a slope of 3:1.
*Add an Infill to the interior.
What is the 2D length of the outermost daylight feature line?
(Use the precision as shown within the properties palette (0.000))- A1342.648
- B1324.648
- C1352.648
27Open PlanProduction.dwg.
Create view frames using the following criteria. From the create view frames wizard, confirm the following:
*Alignment - (1) is selected
*Station range is set to automatic:
*Sheet Settings is set to Plan Only.
*ARCH D Plan Only 20 scale is set to along Alignment.
*View Frame Placement is set to Along Alignmet.
*Accept the reset of the Default selection in the wizard.
*select Create View Frames.
How many individual view frames have been created?- A4
- B3
- C6
28From the Parcel tools menu, click Slide Line - Create to crreate parcels using these layout parameters
*Minimum Area: 0.25 acres
*minimum frontage: 50 feet
*Use Minimum Frontage at Offset: Yes.
*Frontage Offset: 15 feet
*Multiple solution Preference: Use Smallest area
*Automatic Mode: ON
*Remainder Distribution: Create parcel from Remainder
*The parcel to subdivide is parcel 100.
The Frontage is along where parcel 101 shares the parcel segment with parcel 100 as shown in the figure. the parcel segment angle is perpendicular to the fortage.
What is the number of the parcel with the largest area?
- A100
- B200
- C500
29Open DescriptionKeys.dwg.
Create a point description key set with the following description keys:
*STMH
-storm sewer Manhole Point Style
*OAK
-V-TREE-OAK Point Style
-Scale X, Y by parameter 1
*PP
-Utility Pole Style
*PINE
-V-TREE-PALM Point Style
-Scale X, Y by parameter 1
*PECAN
-V-TREE-PALM Point Style
-Scale X, Y by parameter 1
*PALM
-V-TREE-PALM Point Style
-Scale X, Y by parameter 1
Apply the description key to the points in the drawing.
Which letter is not crossed by a point symbol?- AB
- BD
- CG
30Open CorridorQuantities.dwg.
*Use the Road Materials quantity takeoff criteria to compute materials for the sample line group in the drawing.
*Create a material volume table showing the volumes of the Subbase corridor material.
What is the cumulative volume of subbase material at station 5+00?
(Display as shown within the table)- A1570.83
- B1470.83
- C1470.33
31Open createlntersection.dwg
Using the Create Intersection tool, Create an intersection at the intersection point of Road A and Road B. Use the following criteria:
*Select Road B as the main alignmet
-Use All crowns Maintained
-Leave all Geometry Details With the default Values
-Choose to create a new corridor and use Existing Ground as the daylight surface
-Select Create Intersection
*Create a Surface from your corridor intersection using only the TOP code and apply corridor extenst as an outer boudary
Using the spot elevation label style Standard, what is the elevation at the point of intersection ?
(display as shown withn the label style)- A36.97
- B76.973
- C39.67
32Open BoundarySurvery.dwg
Draw a line beginning at the point labeled Iron Pin. the line should have a bearing of N 78-43-27 E and a distance off 500.01 feet.
What is the northing coordinate of the line?
(Provide your answer with a precision of 0.0001 as shown in the point editor dialog box)- A13520.3021
- B1352.03021
- C135203.021
Informationen
- Beschreibung
- Esta evaluación tiene la finalidad de identificar tus conocimientos, por lo que te recomendamos leas con atención las preguntas y marca la opción con la respuesta correcta. Para que puedas realizar este examen, ingresa al siguiente enlace y descarga los archivos que son parte de las instrucciones de esta evaluación. https://studio.bluebeam.com/share/w37ope Agradecemos tu preferencia Mucha Suerte!!!
- Autor
- Alejandro Osio
- Sprache
- Español
- Aufrufe
- 6
- Schlagwörter
- Bewertung
- Noch keine Bewertungen Bewerte dieses Quiz