GoConqr hat ein neues Design! Sag uns, wie es dir gefällt.

Kostenlos registrieren

Quiz

DIKTA ICND 1 Ch 10

Brian Gamble 8 Fragen

Quiz starten

Fragen in diesem Quiz (8)

  1. 1Imagine that a switch connects through an Ethernet cable to a router, and the router’s host name is Hannah. Which of the following commands could tell you information about the IOS version on Hannah without establishing a Telnet connection to Hannah? (Choose two answers.)
    1. Ashow neighbors Hannah
    2. Bshow cdp
    3. Cshow cdp neighbors
    4. Dshow cdp neighbors Hannah
    5. Eshow cdp entry Hannah
    6. Fshow cdp neighbors detail
  2. 2A switch is cabled to a router whose host name is Hannah. Which of the following CDP commands could identify Hannah’s model of hardware? (Choose two answers.)
    1. Ashow neighbors
    2. Bshow neighbors Hannah
    3. Cshow cdp
    4. Dshow cdp interface
    5. Eshow cdp neighbors
    6. Fshow cdp entry Hannah
  3. 3The output of the show interfaces status command on a 2960 switch shows interface Fa0/1 in a “disabled” state. Which of the following is true about interface Fa0/1? (Choose three answers.)
    1. AThe interface is configured with the shutdown command.
    2. BThe show interfaces fa0/1 command will list the interface with two status codes of administratively down and line protocol down.
    3. CThe show interfaces fa0/1 command will list the interface with two status codes of up and down.
    4. DThe interface cannot currently be used to forward frames.
    5. EThe interface can currently be used to forward frames.
  4. 4Switch SW1 uses its Gigabit 0/1 interface to connect to switch SW2’s Gigabit 0/2 interface. SW2’s Gi0/2 interface is configured with the speed 1000 and duplex full commands. SW1 uses all defaults for interface configuration commands on its Gi0/1
    interface. Which of the following are true about the link after it comes up? (Choose
    two answers.)
    1. AThe link works at 1000 Mbps (1 Gbps).
    2. BSW1 attempts to run at 10 Mbps because SW2 has effectively disabled IEEE standard autonegotiation.
    3. CThe link runs at 1 Gbps, but SW1 uses half-duplex and SW2 uses full-duplex.
    4. DBoth switches use full-duplex.
  5. 5The following line of output was taken from a show interfaces fa0/1 command:

    Full-duplex, 100Mbps, media type is 10/100BaseTX

    Which of the following are true about the interface? (Choose two answers.)
    1. AThe speed was definitely configured with the speed 100 interface subcommand.
    2. BThe speed might have been configured with the speed 100 interface subcommand.
    3. CThe duplex was definitely configured with the duplex full interface subcommand.
    4. DThe duplex might have been configured with the duplex full interface subcommand.The speed might have been configured with the speed 100 interface subcommand.
    5. EThe duplex was definitely configured with the duplex full interface
      subcommand.
  6. 6Which of the following commands list the MAC address table entries for MAC addresses configured by port security? (Choose two answers.)
    1. Ashow mac address-table dynamic
    2. Bshow mac address-table
    3. Cshow mac address-table static
    4. Dshow mac address-table port-security
  7. 7On a Cisco Catalyst switch, you issue a show mac address-table command. Which of the following answers list information you would likely see in most lines of output? (Choose two answers.)
    1. AA MAC address
    2. BAn IP address
    3. CA VLAN ID
    4. DType (broadcast, multicast, or unicast)
  8. 8Layer 2 switches SW1 and SW2 connect through a link, with port G0/1 on SW1 andport G0/2 on SW2. The network engineer wants to use 802.1Q trunking on this link.The show interfaces g0/1 switchport command on SW1 shows the output listedhere:

    SW1# show interfaces gigabit0/1 switchport
    Name: Gi0/1
    Switchport: Enabled
    Administrative Mode: trunk
    Operational Mode: trunk

    Which of the following must be true on switch SW2’s G0/2 port?
    1. AThe operational state per the show interfaces switchport command must be“trunk.”
    2. BThe administrative state per the show interfaces switchport command must be“trunk.”
    3. CSW2 must use the switchport mode trunk configuration command on G0/2, orthe link will not use trunking.
    4. DSW2 can use the switchport mode dynamic auto configuration command as one option to make the link use trunking.

Informationen

Beschreibung
Final / Review ICND 1 Quiz am DIKTA ICND 1 Ch 10, erstellt von Brian Gamble am 29/02/2016.
Sprache
English
Aufrufe
141
Bewertung
Noch keine Bewertungen
Bewerte dieses Quiz
Bewerte dieses Quiz

Feedback

Worum geht es?

Wie gefällt dir das neue Design?

Dein Eindruck