Test
Millwright Test 1
Crea una cuenta gratis para terminar este test
Guarda tu progreso y consulta tu resultado final.
¿Ya tienes cuenta? Inicia sesión
Preguntas del test (92)
1What Part and Section of the OHS Code describes the membership of a joint work site health and safety committee?
- APart 12, Section 197
- BPart 13, Section 197
- CPart 14, Section 197
- DPart 15, Section 197
2What Part and Section of the OHS Code describes the requirements and options for protective footwear?
- APart 18, Section 229
- BPart 18, Section 232
- CPart 18, Section 233
- DPart 18, Section 236
3What Part and Section of the OHS Code describes the requirements and options for worker training about WHMIS?
- APart 29, Section 394
- BPart 29, Section 395
- CPart 29, Section 396
- DPart 29, Section 397
4What are the first aid requirements for high hazard work at a close work site with 5 to 9 workers at the work site per shift?
- A1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit, 3 blankets
- B2 Standard First Aiders, No. 2 First Aid Kit, 3 blankets
- C2 Standard First Aiders, No. 3 First Aid Kit, 3 blankets, stretcher, splint
- D1 Emergency First Aider, 1 Standard First Aider, No. 2 First Aid Kit
5What is employer responsibility with regard to hazard assessment at the work site?
- Ato provide easy and immediate access for any worker to the OHS Act, Regulation and Code at the work site
- Bto ensure suppliers are aware of their responsibility to provide necessary information on any hazards related to their products
- Cto develop a plan to eliminate or control any hazard identified at the work site
- Dto ensure all workers participate in daily meetings to inspect their tools and plan their work
6How is Workers Compensation Board of Alberta funded?
- A100% of the funding for the WCB comes from employers in Alberta.
- B75% of the funding for the WCB comes from employers and 25% comes from the provincial government
- C50% of the funding for the WCB comes from employers, 25% from the provincial government and 25% from employees
- D33% of the funding for the WCB comes from employers, 34% from the provincial government and 33% from employees
7What are the four categories of workplace hazards?
- Aecological, chemical, ergonomic, physical
- Bbiological, chemical, ergonomic, physical
- Cbiological, ecological, chemical, physical
- Dchemical, physical, psychological, ecological
8What is an example of an engineering control for worker protection?
- Arenovation
- Bsubdivision
- Cisolation
- Dactivation
9When is an administrative control put in place for worker protection?
- ATo identify the correct personal protective equipment to be used in a hazardous situation
- BTo document the details of the implementation of an engineering control
- CWhen an engineering control cannot eliminate or control a hazard
- DTo isolate a hazard through containment or enclosure
10Who is responsible to have an emergency response plan in place at work site?
- Aemployees
- BOHS inspector
- Cjoint work site health and safety committee
- Demployers
11What part of the OHS Code convers first aid requirements at the work site?
- APart 10
- BPart 11
- CPart 12
- DPart 13
12What must your employer do if first aid supplies are stored in secure containers at the work site?
- AEnsure the containers are clearly marked to indicate their contents
- BEnsure the containers are stored in a dust proof environment
- CEnsure the containers are not stacked more than 3 layers high
- DEnsure the containers are inspected monthly to ensure contents are safe
13What number and type of first aiders must your employer ensure are present at an isolated work site with low hazard assessment rating and 65 workers at the work site per shift?
- A1 Standard First Aider
- B1 Standard First Aider and 1 Emergency First Aider
- C2 Standard First Aiders
- D2 Standard First Aiders and 1 Emergency First Aider
14What is the duty to use personal protective equipment according to the Alberta OHS Code?
- Aa clause that must be included in the employment contract of every construction worker in Alberta
- Ba sign that must be posted at the entrance to any work site where PPE is required
- Cthe part of the OHS Code that describes the different types of PPE to be used on the work site
- Dwhat you and your employer must do if a hazard assessment identifies the need for the use of PPE
15Who is responsible to ensure work site emergency response plans remain up to date?
- Athe employer
- Bthe employer and the employees
- Cthe employees
- Dthe OHS inspector
16When a work site hazard assessment identifies that workers are required to wear PPE what is your employer's responsibility?
- AEnsure all workers are informed about the need to wear PPE
- BEnsure all workers properly use and wear the required PPE
- CPut up posters indicating a hazard assessment has identified that PPE is required
- DEnsure all workers are provided with funding to purchase required PPE
17What is an employee responsibility with regard to the use of PPE?
- Ato inspect your PPE once a month
- Bto modify poor fitting PPE so it fits properly
- Cto inspect your PPE prior to each use
- Dto wear your PPE only when you sense an accident may happen
18Industrial protective headwear must comply with what standard?
- AULC
- BPPE
- CWCB
- DCSA
19What is not an obligation your employer assumes when a hazard assessment indicates the need for PPE?
- Ato post a Duty To Use Personal Protective Equipment sign at all entrances to the work site
- Bto ensure employees are trained in the use, care, limitations and maintenance of their PPE
- Cto ensure workers properly use and wear PPE
- Dto ensure the PPE is in a condition to perform the function intended
20What is a characteristic of protective footwear with a yellow triangle on the outer side or tongue of the right shoe?
- Asole puncture protection and Grade 2 protective toe (will withstand impact up to 90 Joules)
- Bsoles that provide electrical shock protection and a Grade 2 protective toe (will withstand impact up to 90 Joules)
- Csole puncture protection and Grade 1 protective toe (will withstand impact up to 125 Joules)
- Dsoles that provide electrical shock protection and a Grade 1 protective toe (will withstand impact up to 125 Joules)
21In what situation is your employer obligated to provide you with proper PPE according the OHS Code?
- Awhen required PPE must be replaced more frequently that once a year
- Bwhen required PPE must be replaced more frequently that once every 2 years
- Cwhen workers are exposed to respiratory hazard or excessive noise levels
- Dwhen workers are exposed to respiratory hazards only
22Who is responsible for providing workers with WHMIS training?
- AThe supplier of controlled products.
- BA training institute or provider.
- CThe employee must obtain their own training.
- DThe employer must provide the training.
23Employers are responsible to:
- Aprovide a MSDS for each controlled product used in the workplace.
- Binform all workers about chemical hazards at the work site.
- Ctrain workers about labels, MSDS and other identifiers.
- Dall of the above.
24Suppliers of controller products are responsible to:
- Atrain employees to safely dispose of hazardous products.
- Bprovide SDS for controlled product they sell or import.
- Cprovide extra labels for employees to use when transferring controlled
products from the original container. - Dvisit work sites to ensure controlled products are labelled properly.
25Employees are responsible to:
- Aclassify controlled products.
- Btrain other employees about WHMIS.
- Capply workplace labels where and when required.
- Densure SDS are readily available.
26The key elements of WHMIS are:
- Aemployee education, SDS and product labelling.
- BHazard Products Act, OHS and SDS.
- Cemployee labelling, SDS and employer training.
- Dproduct labeling, OHS and Controlled Products Regulations.
27The goal of WHMIS is to:
- Aensure workers have containers for controlled products.
- Bensure suppliers of controlled products provide training for all employees.
- Cprotect the worker by providing information on hazardous materials.
- Densure that the requirements for information on hazardous materials are
unique to the requirements of each province.
28An SDS must be provided for each controlled product because they:
- Aprovide only the essential information from the label and are easier to read in an emergency.
- Bcontain the generic product names and are easier to locate and read than the labels on the containers.
- Care only for the employer's use when an emergency arises, and they can be
retrieved from a secure location. - Dprovide more detailed information than can be provided on a label.
29The supplier label is attached to the:
- Acontainer in which the product is shipped.
- Bcontainer in which the product is stored.
- Cwork site near where the product is used.
- Dinvoice when the product is delivered.
30How do you identify a portable gasoline container that is approved for use? It:
- Ais approved under the Alberta Occupational Health and Safety Code.
- Bis approved by the Alberta Hazardous Materials Control Regulations.
- Chas a MSDS label affixed to the outside of the container.
- Dis approved by either one or both of the ULC or CSA.
31Ventilation system requirements for the work site are found in the:
- Aprovincial and national building codes.
- BAlberta Occupational Health and Safety Code.
- CWCB Worker Handbook.
- DAlberta Construction Safety Association.
32Before entering a confined workspace you should:
- Aassemble all necessary tools and equipment to ensure easy access while
working in the confined space. - Bcontact your employer to obtain information on dangerous gases present in
the confined workspace. - Cdiscuss your work plan with other workers who may have worked in a
similar confined space. - Duse a gas detector to determine whether the area contains any dangerous
fumes or gases.
- Aassemble all necessary tools and equipment to ensure easy access while
33What type of fire extinguisher is versatile in fighting different types of fires?
- Aregular dry chemical
- Bpurple K dry chemical
- Cmulti-purpose dry chemical
- Ddry powder
34Fasteners used in explosive actuated tools are:
- Acommon nails with washers
- Bmanufactured from special steel and tempered
- Cvery hard and brittle
35A drive pin is a fastener used to:
- Asupport wire for suspending a ceiling
- Bpermanently attach one material to another
- Cattach one material to another with a nut
36To determine the suitability of a base material, use a fastener as a center punch struck by a single average hammer blow. If the fastener is blunted (meaning it can't fasten) the material is too:
- Asoft
- Bhard
- Cbrittle
37To determine the suitability of a base material, use a fastener as a center punch struck
by a single average hammer blow. If the fastener penetrates easily, do not fasten
because the material is too:- Asoft
- Bhard
- Cbrittle
38To determine the suitability of a base material, use a fastener as a center punch struck
by a single average hammer blow. If material cracks or shatters, do not fasten
because the material is too:- Asoft
- Bhard
- Cbrittle
39A threaded knurled pin is designed for what material?
- Amild steel
- Bconcrete block
- Cconcrete
- Dtempered steel
40To be a qualified operator of an explosive actuated tool you must possess:
- Aa valid driver's license from Alberta.
- Bfirearms training.
- Ctraining in the use of each tool and familiarity with local safety regulations.
- Dknowledge of the safety regulations.
41OH&S states that operators of explosive actuated tools should always wear:
- Awork gloves.
- Bear plugs.
- Chard hat.
- Deye protection.
42If a tool is found to be defective, you should:
- Amark it defective and call a service representative.
- Btry to fix it yourself.
- Csell it at a discount.
- Dthrow it away.
43According to OH&S, what safety equipment is required when using an explosive
actuated tool in a confined area such as a small room?- Awork gloves and hard hat
- Bear plugs and eye protection
- Chard hat and eye protection
- Deye protection and steel-toed boots
44How much oil should be added to tool parts after cleaning?
- Aone or two drops
- Bseveral drops
- Capply liberally to a cloth and wipe all parts
- Dnone
45What part requires replacement most often in a low velocity tool?
- Afiring pin
- Btrigger
- Cbuffer
- Dpiston
46The width of the saw blade cut in the workpiece is called:
- Aset.
- Bblade pitch.
- Cstraight or wavy.
- Dkerf.
47The purpose of draw filing is to:
- Aremove metal rapidly.
- Bproduce a smooth and flat surface.
- Cfinish rough surfaces.
- Dremove sharp corners and burrs.
48The removable serrated jaws on a bench vise are made from:
- Aaluminum.
- Bhardened steel.
- Ccast steel.
- Dcast iron.
49A standard screwdriver blade maintains a better grip in the slot if the blade is ground
slightly:- Atapered.
- Bconcave.
- Cconvex.
- Drounded.
50The included angle that should be ground on the point of a center punch is:
- A30° to 60°
- B90°
- C120°
- D150°
51When tightening a bolt with a wrench:
- Aan adjustable wrench gives the most precise fit on a hexagon headed bolt.
- Buse a pipe on the end of the wrench to increase torque.
- Cnever push; always pull.
- Dnever pull; always push.
52The reason for the crown on the end of a flat scraper is:
- Aso that the outside edges do not dig into the finished workpiece.
- Bto increase the area of the cutting edge.
- Cto produce a sharp cutting edge.
- Dto make it easier to scrape internal cylindrical surfaces.
53Which is a purpose of a flat (cold) chisel?
- Acutting keys and grooves
- Bcutting oil grooves
- Ccutting off rivets
- Dsquaring up keyseat corners
54What is a chisel made from?
- Aaluminum
- Bhigh carbon steel
- Clow carbon steel
- Dstainless steel
55Alkaline cleaning must only be used on which of the following metals.
- Aaluminum
- Bzinc
- Clead
- Diron
56Barrel finishing:
- Ais a quick and inexpensive cleaning method.
- Bis inexpensive and many parts can be completed at once.
- Cuses high pressure air and steam.
- Duses petroleum-based products.
57In the lapping process, which is charged?
- Athe hardened roller
- Bthe hardened steel block
- Cthe lap
- Dthe workpiece
58What is another name for Hand Pads and Rolls?
- AScotch-Brite pads
- Bscrub pads
- CSoS pads
- Dsponge pad
59The three hand taps found in a set are the:
- Astarter, plug and bottoming
- Btaper, plug and bottoming
- Ctaper, intermediate and finishing
- Dstarter, intermediate and chamfered.
60What is the tap drill size for a 3/4-10 UNC 2B?
- A3/4 inch
- B21/32 inch
- C37/64 inch
- D11/16 inch
61If a high-speed steel hand tap breaks in a hole, one way to remove it is:
- Awith an electrical discharge machine.
- Bby drilling it out with a high-speed steel drill bit.
- Cby drilling a hole and using a stud extractor.
- Dwith a tap vibrator.
62You have to choose between four steel rods to cut a 1/2-13 UNC 2A thread with an
adjustable split die. Which diameter rod would you use?- A0.489
- B0.497
- C0.503
- D0.515
63Choose the correct tool to turn a die.
- Adie wrench
- Bdie stock
- Cdie plate
- Ddie handle
64The cutting action of a hand broach is performed by a series of successive teeth, each
protruding:- A0.001 inch further than the preceding tooth.
- B0.002 inch further than the preceding tooth.
- C0.0003 inch further than the preceding tooth.
- D0.003 inch further than the preceding tooth.
65Hand reamers must be rotated:
- Acounter-clockwise.
- Bclockwise.
- Cin reverse.
- Dforward.
66Pullers are used to:
- Amove heavy equipment in a horizontal plane.
- Bmove heavy equipment in a vertical plane.
- Cremove bearings, hubs and sprockets.
- Dremove large heavy shafts.
67Before working around a load that has been raised with a hydraulic jack:
- Athe load must be blocked.
- Bthe jack handle must be removed.
- Cthe hydraulic fluid should be checked.
- Dthe jack should be seated on a flat surface.
68Master precision levels should be picked up by the:
- Abottom surface.
- Bvials.
- Ctop plate.
- Dsides.
69A mechanic's level has a sensitivity of:
- A0.0005 inch per foot per division.
- B0.001 inch per foot per division.
- C0.005 inch per foot per division
- D0.010 inch per foot per division.
70Levelling feet are used on:
- Aheavy equipment.
- Blarge machine tools.
- Csmall lightweight equipment.
- Dvibrating equipment.
71You can level machine tools with a carpenter's level.
- AVerdadero
- BFalso
72Wind can affect both plumb bobs and vertical wires.
- AVerdadero
- BFalso
73Which anchor bolt can you replace easily if you break it?
- Afixed
- Bflexible
- Cdrop-in
- Dboxed
74
Which anchor is designed to accommodate slight adjustment?- Afixed
- Bflexible
- Cexpansion bolt
- Ddrop-in
75Which anchor is best suited for the edge of a concrete foundation?
- Aexpansion bolt
- Bfixed
- Cadhesive
- Ddrop-in
76Reference lines are also known as:
- Aworking lines.
- Bcontrol lines.
- Cdatum lines.
- Dall of the above.
77A 12-inch master precision level requires 0.003 inch of shims under one end to bring it level when it is placed longitudinally on the bed of a machine tool eight feet long. What size shim should be placed under the end of the machine tool to level it?
- A0.002 inch
- B0.003 inch
- C0.012 inch
- D0.024 inch
78Do not apply grout to a smooth concrete surface.
- AVerdadero
- BFalso
79Homemade grout mixtures tend to shrink.
- AVerdadero
- BFalso
80You can place polymeric grouts in colder temperatures than cement-based grouts.
- AVerdadero
- BFalso
81Before grouting, you should torque anchor bolts:
- Ato their final value.
- Bto 50% of their final value.
- Cto 25% of their final value.
- Dnot at all until the grout has cured.
82Grout is so stiff that formwork is not required.
- AVerdadero
- BFalso
83A master precision level has a sensitivity of:
- A5 microns per foot per division.
- B0.0001 inch per foot per division.
- C0.0005 inch per foot per division.
- D0.001 inch per foot per division.
84When using wire sag charts to determine the levelness of a machine bed, deduct the
sag from the measured vertical distance to give the true vertical distance.- AVerdadero
- BFalso
85Because reference lines are all very accurate, you can take important measurements
from either side of any one of them.- AVerdadero
- BFalso
86Do not place cement-based grout mixtures below what temperature?
- A5°C
- B0°C
- C-5°C
- D-10°C
87The kind of abrasive material used in grinding wheels for general purpose
applications is:- Asilicon carbide.
- Bboron carbide.
- Caluminum oxide.
- Ddiamond.
88It is safe to carry a portable grinder by the power cord.
- AVerdadero
- BFalso
89It is safe to use standard sockets with electric impact wrenches.
- AVerdadero
- BFalso
90The larger the power drill, the slower the rpms and higher the torque.
- AVerdadero
- BFalso
91Most cordless drills have torque control
- AVerdadero
- BFalso
92Prolonged use of power or air tools can cause carpal tunnel syndrome.
- AVerdadero
- BFalso
Información
- Descripción
- Millwright CofQ Millwright Exam Prep. Test sobre Millwright Test 1, creado por Lukasz N el 08/04/2022.
- Autor
- Lukasz N
- Idioma
- English
- Visitas
- 17
- Etiquetas
- Valoración
- Aún sin valoraciones Valora este test