Ajude a dar forma ao GoConqr. O que a gente deve adicionar?

Quiz

Chapter 6 Cisco’s Internetworking Operating System (IOS)

Kessi Silva 20 perguntas

Fazer o quiz

Perguntas do quiz (20)

  1. 11. You type show interfaces fa0/1 and get this output:

    275496 packets input, 35226811 bytes, 0 no buffer
    Received 69748 broadcasts (58822 multicasts)
    0 runts, 0 giants, 0 throttles
    111395 input errors, 511987 CRC, 0 frame, 0 overrun, 0 ignored
    0 watchdog, 58822 multicast, 0 pause input
    0 input packets with dribble condition detected
    2392529 packets output, 337933522 bytes, 0 underruns
    0 output errors, 0 collisions, 1 interface resets
    0 babbles, 0 late collision, 0 deferred
    0 lost carrier, 0 no carrier, 0 PAUSE output
    0 output buffer failures, 0 output buffers swapped out

    What could the problem possibly be with this interface?
    1. ASpeed mismatch on directly connected interfaces
    2. BCollisions causing CRC errors
    3. CFrames received are too large
    4. DInterference on the Ethernet cable
  2. 2The output of the show running-config command comes from _________.
    1. ANVRAM
    2. BFlash
    3. CRAM
    4. DFirmware
  3. 3Which two of the following commands are required when configuring SSH on your router?
    1. Aenable secret password
    2. Bexec-timeout 0 0
    3. Cip domain-name name
    4. Dusername name password password
    5. Eip ssh version 2
  4. 4Which command will show you whether a DTE or a DCE cable is plugged into serial 0/0 on your router’s WAN port?
    1. Ash int s0/0
    2. Bsh int serial0/0
    3. Cshow controllers s0/0
    4. Dshow serial0/0 controllers
  5. 5In the work area, drag the router term to its definition on the right.
    1. AMode Definition
      user exec mode -----------------Commands that affect interfaces/processes only fk
      privileged exec mode -----------Commands that affect the entire system
      Global configuration mode ------Interactive configuration dialog
      Specific configuration modes----Provides access to all other router commands
      Setup mode ---------------------Limited to basic monitoring commands
    2. BMode Definition
      user exec mode -----------------Limited to basic monitoring commands
      privileged exec mode -----------Provides access to all other router commands
      Global configuration mode ------Commands that affect the entire system
      Specific configuration modes----Commands that affect interfaces/processes only fk
      Setup mode ---------------------Interactive configuration dialog
    3. CMode Definition
      user exec mode -----------------Limited to basic monitoring commands
      privileged exec mode -----------Interactive configuration dialog
      Global configuration mode ------Commands that affect interfaces/processes only fk
      Specific configuration modes----Provides access to all other router commands
      Setup mode ---------------------Limited to basic monitoring commands
    4. DMode Definition
      user exec mode -----------------Limited to basic monitoring commands
      privileged exec mode -----------Commands that affect interfaces/processes only fk
      Global configuration mode ------Interactive configuration dialog
      Specific configuration modes----Provides access to all other router commands
      Setup mode ---------------------Limited to basic monitoring commands
  6. 6Using the given output, what type of interface is shown?

    [output cut]
    Hardware is MV96340 Ethernet, address is 001a.2f55.c9e8 (bia 001a.2f55.c9e8)
    Internet address is 192.168.1.33/27
    MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
    reliability 255/255, txload 1/255, rxload 1/255
    1. A10 Mb
    2. B100 Mb
    3. C1000 Mb
    4. D1000 MB
  7. 7Which of the following commands will configure all the default VTY ports on a switch?
    1. ASwitch# line vty 0 4
    2. BSwitch(config)# line vty 0 4
    3. CSwitch(config-if)# line console 0
    4. DSwitch(config)# line vty all
  8. 8Which of the following commands sets the privileged mode password to Cisco and encrypts the password?
    1. Aenable secret password Cisco
    2. Benable secret cisco
    3. Cenable secret Cisco
    4. Denable password Cisco
  9. 9If you wanted administrators to see a message when logging into the switch, which command would you use?
    1. Amessage banner motd
    2. Bbanner message motd
    3. Cbanner motd
    4. Dmessage motd
  10. 10Which of the following prompts indicates that the switch is currently in privileged mode?
    1. ASwitch(config)#
    2. BSwitch>
    3. CSwitch#
    4. DSwitch(config-if)

Informações

Descrição
2.0 LAN Switching T echnologies 2.3 T roubleshoot interface and cable issues (collisions, errors, duplex, speed) 5.0 Infrastructure Management 5.3 Configure and verify initial device configuration 5.4 Configure, verify, and troubleshoot basic device hardening 5.4.a Local authentication 5.4.b Secure password 5.4.c Access to device 5.4.c. (iii) Data 5.4.d Source address T elnet/SSH 5.4.e Login banner 5.6 Use Cisco IOS tools to troubleshoot and resolve problems
Idioma
English
Visualizações
9
Etiquetas
ccna toddcertificação tecnológica
Avaliação
Ainda sem avaliações
Avalie este quiz
Avalie este quiz

Mais sobre Switch Configuration and Administration

Fale Conosco

Sobre o que é sua mensagem?

O que a gente deve adicionar?