Ajude a dar forma ao GoConqr. O que a gente deve adicionar?

Flashcards

Mechanisms flashcards

Nuño Nieto Espanhol 20 flashcards

1. Illustrates the transmission of power by simple pulleys and an open belt. In this case both of the pulleys rotate in the…

Flashcards do conjunto (20)

  1. 1—1. Illustrates the transmission of power by simple pulleys and an open belt. In this case both of the pulleys rotate in the same direction.1. Illustrates the transmission of power by simple pulleys and an open belt. In this case both of the pulleys rotate in the same direction.
  2. 2—2. Differs from 1 in the substitution of a crossed belt for the open one. In this case the direction of rotation of the pulleys is reversed. By arranging three pulleys, side by side, upon the shaft to be driven, the middle one fast and the other two loose upon it, and using both an open and a crossed belt, the direction of the said shaft is enabled to be reversed without stopping or reversing the driver. One belt will always run on the fast pulley, and the other on one of the loose pulleys. The shaft will be driven in one direction or the other, according as the open or crossed belt is on the fast pulley.2. Differs from 1 in the substitution of a crossed belt for the open one. In this case the direction of rotation of the pulleys is revers...
  3. 3—5. Resembles 1, with the addition of a movable tightening pulley, B. When this pulley is pressed against the band to take up the slack, the belt transmits motion from one of the larger pulleys to the other; but when it is not, the belt is so slack as not to transmit motion.5. Resembles 1, with the addition of a movable tightening pulley, B. When this pulley is pressed against the band to take up the slack, t...
  4. 4—6. By giving a vibratory motion to the lever secured to the semi-circular segment, the belt attached to the said segment imparts a reciprocating rotary motion to the two pulleys below.6. By giving a vibratory motion to the lever secured to the semi-circular segment, the belt attached to the said segment imparts a recipr...
  5. 5—15. Represents what are known as White’s pulleys, which can either be made with separate loose pulleys, or a series of grooves can be cut in a solid block, the diameters being made in proportion to the speed of the rope; that is, 1, 3, and 5 for one block, and 2, 4, and 6 for the other. Power as 1 to 7.15. Represents what are known as White’s pulleys, which can either be made with separate loose pulleys, or a series of grooves can be cut...
  6. 6—20. Are different arrangements of pulleys. The following rule applies to these pulleys:—In a system of pulleys where each pulley is embraced by a cord attached at one end to a fixed point and at the other to the center of the movable pulley, the effect of the whole will be = the number 2, multiplied by itself as many times as there are movable pulleys in the system.20. Are different arrangements of pulleys. The following rule applies to these pulleys:—In a system of pulleys where each pulley is embra...
  7. 7—24. Spur-gears.24. Spur-gears.
  8. 8—34. An internally toothed spur-gear and pinion. With ordinary spur-gears (such as represented in 24) the direction of rotation is opposite; but with the internally toothed gear, the two rotate in the same direction; and with the same strength of tooth the gears are capable of transmitting greater force, because more teeth are engaged.34. An internally toothed spur-gear and pinion. With ordinary spur-gears (such as represented in 24) the direction of rotation is opposit...
  9. 9—38. A means of converting rotary motion, by which the speed is made uniform during a part, and varied during another part, of the revolution.38. A means of converting rotary motion, by which the speed is made uniform during a part, and varied during another part, of the revolut...
  10. 10—55. Different velocity given to two gears, A and C, on the same shaft, by the pinion, B.
    Notes:
    Brown originally referred to the pinion D, but there is no D in the original illustration. We have corrected it to B.
    55. Different velocity given to two gears, A and C, on the same shaft, by the pinion, B. Notes: Brown originally referred to the pinion D...
  11. 11—68. The single tooth, A, of the driving-wheel, B, acts in the notches of the wheel, C, and turns the latter the distance of one notch in every revolution of C. No stop is necessary in this movement, as the driving-wheel, B, serves as a lock by fitting into the hollows cut in the circumference of the wheel, C, between its notches.68. The single tooth, A, of the driving-wheel, B, acts in the notches of the wheel, C, and turns the latter the distance of one notch in ...
  12. 12—69. B, a small wheel with one tooth, is the driver, and the circumference entering between the teeth of the wheel, A, serves as a lock or stop while the tooth of the small wheel is out of operation.69. B, a small wheel with one tooth, is the driver, and the circumference entering between the teeth of the wheel, A, serves as a lock or...
  13. 13—92. Ordinary crank motion.92. Ordinary crank motion.
  14. 14—94. Variable crank, two circular plates revolving on the same center. In one a spiral groove is cut; in the other a series of slots radiating from the center. On turning one of these plates around its center, the bolt shown near the bottom of the figure, and which passes through the spiral groove and radial slots, is caused to move toward or from the center of the plates.94. Variable crank, two circular plates revolving on the same center. In one a spiral groove is cut; in the other a series of slots radia...
  15. 15—97. This is a heart-cam, similar to 96, except that it is grooved.97. This is a heart-cam, similar to 96, except that it is grooved.
  16. 16—99. Spiral guide attached to the face of a disk; used for the feed-motion of a drilling machine.99. Spiral guide attached to the face of a disk; used for the feed-motion of a drilling machine.
  17. 17—100. Quick return crank motion, applicable to shaping machines.100. Quick return crank motion, applicable to shaping machines.
  18. 18—101. Rectilinear motion of horizontal bar, by means of vibrating slotted bar hung from the top.101. Rectilinear motion of horizontal bar, by means of vibrating slotted bar hung from the top.
  19. 19—115. Rotary motion of the toothed wheels produces rectilinear motion of the double rack and gives equal force and velocity to each side, both wheels being of equal size.115. Rotary motion of the toothed wheels produces rectilinear motion of the double rack and gives equal force and velocity to each side, ...
  20. 20—118. A mode of doubling the length of stroke of a piston-rod, or the throw of a crank. A pinion revolving on a spindle attached to the connecting-rod or pitman is in gear with a fixed rack. Another rack carried by a guide-rod above, and in gear with the opposite side of the pinion, is free to traverse backward and forward. Now, as the connecting-rod communicates to the pinion the full length of stroke, it would cause the top rack to traverse the same distance, if the bottom rack was alike movable; but as the latter is fixed, the pinion is made to rotate, and consequently the top rack travels double the distance.118. A mode of doubling the length of stroke of a piston-rod, or the throw of a crank. A pinion revolving on a spindle attached to the co...

Informações

Descrição
FlashCards sobre Mechanisms flashcards, criado por Nuño Nieto em 03-11-2021.
Criado por
Nuño Nieto
Visualizações
2
Avaliação

Fale Conosco

Sobre o que é sua mensagem?

O que a gente deve adicionar?