CCNP Route

Por favor, aguarde! Carregando...

Questão 1 de 60

How do EIGRP routers establish and maintain neighbor relationships?

Selecione uma ou mais das seguintes:

by exchanging neighbor tables with directly attached routers
by comparing known routes to information received in updates
by exchanging hello packets with neighboring routers
by dynamically learning new routes from neighbors
by exchanging routing tables with directly attached routers

Explicação

Questão 2 de 60

The IPv6 autoconfiguration feature enables a PC to automatically connect to an IPv6 network. What type of IPv6 address allows a PChost to send a router solicitation message requesting a prefix for stateless autoconfiguration?

Selecione uma ou mais das seguintes:

link local address
site local address
aggregatable global unicast address
loopback address
IPv4-compatible address
flow-label address

Explicação

Questão 3 de 60

During an interview, the company IT manager mentions that the company has two critical communication links to its main supplier. These links require an uptime of 24/7. Which part of the PPDIOO process is most affected by this information?

Selecione uma ou mais das seguintes:

implementation phase
design phase
routing protocol selection
prototype design plan

Explicação

Questão 4 de 60

Refer to the exhibit. The RIP routes must be injected into the OSPF domain. Which command will perform external route summarization?

Selecione uma ou mais das seguintes:

RTA(config-router)#
summary-address 172.20.0.0 255.255.0.0
RTB(config-router)#
summary-address 192.168.16.0 255.255.252.0
RTB(config-router)#
area 1 range 192.168.16.0 255.255.252.0
RTA(config-router)#
area 1 range 172.20.0.0 255.255.0.0

Explicação

Questão 5 de 60

Refer to the exhibit.
access-list 111 permit ip 10.0.0.0 0.255.255.255 any

route-map net-10 permit 10
match ip address 111
set interface FastEthernet 0/1

Where would the system administrator apply the above configuration to establish policy-based routing that directs packets from the10.0.0.0/8 network through the R2 router to the Internet?

Selecione uma ou mais das seguintes:

RTA interface Fa 0/0
RTA interface Fa 0/1
RTB interface Fa 0/1
RTB interface Fa 1/0
R2 interface Fa 0/0
R2 interface Fa 0/1

Explicação

Questão 6 de 60

How does OSPF exchange routing updates when the passive -interface command is applied?

Selecione uma ou mais das seguintes:

OSPF forms neighbor adjacencies on that interface.
The OSPF interface enters an active state.
OSPF stops sending routing updates out that interface.
OSPF only receives routing updates on that interface.
OSPF neither sends nor receives routing updates through that interface.

Explicação

Questão 7 de 60

Which functional component of the Cisco Enterprise Architecture is responsible for hosting internal servers?

Selecione uma ou mais das seguintes:

enterprise campus
enterprise edge
service provider edge
building distribution

Explicação

Questão 8 de 60

Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?

Selecione uma ou mais das seguintes:

The same key chain name must be used on each router.
The same number of key strings must be used on each router.
The key string should be used in interface mode instead of the key chain.
The same autonomous system numbers must be used in the interface configurations of each router.
The authentication configuration is correct, but the
show ip eigrp neighbors
command should be issued to troubleshoot the issue.

Explicação

Questão 9 de 60

Refer to the exhibit. A GRE tunnel must be configured between routers RTA and RTB. Assume that router RTB has been correctly configured. Which command would correctly configure router RTA to encrypt traffic that is destined for router RTB?

Selecione uma ou mais das seguintes:

access-list 101 permit gre 172.16.1.0 0.0.0.255 172.16.3.0 0.0.0.255
access-list 101 permit gre host 172.16.1.1 host 172.16.3.1
access-list 101 permit ip 172.16.1.0 0.0.0.255 172.16.3.0 0.0.0.255
access-list 101 permit ip host 172.16.1.1 host 172.16.3.1
access-list 101 permit gre host 192.168.12.1 host 192.168.23.3
access-list 101 permit gre host 192.168.23.3 host 192.168.12.1

Explicação

Questão 10 de 60

What does the log message %DUAL-3-SIA: Route 10.1.2.0/24 stuck in active state in IP-EIGRP 24 mean?

Selecione uma ou mais das seguintes:

An EIGRP reply packet was not received from one or more neighbors within the time frame of 180 seconds.
DUAL has detected a routing loop for the 10.1.2.0/24 network.
EIGRP neighbors on the 10.1.2.0/24 network are stuck in the DUAL active state.
EIGRP for AS 24 is not yet configured for DUAL.

Explicação

Questão 11 de 60

Refer to the exhibit. Which route redistribution statement is true?

Selecione uma ou mais das seguintes:

No metric is set for OSPF routes redistributed into EIGRP.
OSPF is redistributed into EIGRP with a default metric of 1.
No seed metric is set for redistributed RIP routes into EIGRP.
RIP routes are redistributed into EIGRP with a seed metric of infinity.
Both RIP and OSPF will be redistributed into EIGRP with the same seed metric.

Explicação

Questão 12 de 60

Which access technology would be the most insecure to use when interconnecting a branch site?

Selecione uma ou mais das seguintes:

cable or DSL
Frame Relay
IPsec VPN
leased line
MPLS VPN
SSL

Explicação

Questão 13 de 60

Refer to the exhibit. The BGP sessions are established between all routers. RTC receives route updates for network 170.10.0.0 from autonomous system 300 with the weight attribute set to 3000. RTB learns about network 170.10.0.0 from autonomous system 200 with a weight of 2000. Which router will be used by RTA as a next hop to reach network 170.10.0.0?

Selecione uma ou mais das seguintes:

RTC because of the highest weight
RTC because of the T1 link
RTC because of the longest AS_Path
RTB because of the lowest weight
RTB because of the slow 64-kb/s link
RTB because of the shortest AS_Path

Explicação

Questão 14 de 60

Refer to the exhibit. How is the OSPF default gateway entry determined for R2?

Selecione uma ou mais das seguintes:

Default routes are automatically injected by OSPF into all advertisements.
A static default gateway route is defined in the configuration of R2.
The default-information originate command is applied on R1.
The ISP defines the gateway of last resort and automatically passes it to R1 and R2.
The ip default-gateway command is applied on R2.

Explicação

Questão 15 de 60

Refer to the exhibit. OSPF and OSPFv3 have been configured on routers R1 and R2. However, they can exchange routing updates for OSPF but not for OSPFv3. What additional step should be taken to remedy the problem?

Selecione uma ou mais das seguintes:

Configure interface Fa0/1 on R2 with the ipv6 address 2001::/64 eui-64 command.
Configure interface Fa0/0 on R1 with ipv6 address FE80::2E0:F7FF:FE45:7403 command.
Remove the IPv4 addresses on both routers R1 and R2 in order for OSPFv3 to exchange routing updates.
Remove the global IPv6 address from Fa0/0 interface on R1 in order for OSPFv3 to use the link-local address to exchange routingupdates.

Explicação

Questão 16 de 60

Refer to the exhibit. Based on the configuration in the exhibit, which statement is true?

Selecione uma ou mais das seguintes:

Access list 1 specifies that packets with a destination address of 192.168.1.0 will be policy-routed.
Access list 2 specifies that packets with a source address of 172.16.1.0 will be policy-routed.
Packets that match access list 1 will be sent to the next-hop address 172.17.1.2.
Packets that match access list 2 will be denied access.
Both match statements must be true for route map ISP1 to be true.

Explicação

Questão 17 de 60

When would the network administrator use the ip bandwidth -percent eigrp as-number percent command?

Selecione uma ou mais das seguintes:

when there is a low bandwidth connection
when the connection is on a shared medium
when the connection is serial instead of Ethernet
when the link is always busy

Explicação

Questão 18 de 60

Which two EIGRP and MPLS implementation statements are true? (Choose two.)

Selecione uma ou mais das seguintes:

Two EIGRP routers must be on the same IP subnet when connecting over a Layer 2 MPLS VPN backbone.
Two EIGRP routers must be on the same IP subnet when connecting over a Layer 3 MPLS VPN backbone.
Two EIGRP routers must be on different IP subnets when connecting over a Layer 2 MPLS VPN backbone.
Two EIGRP routers must be on different IP subnets when connecting over a Layer 3 MPLS VPN backbone.

Explicação

Questão 19 de 60

Refer to the exhibit. A network administrator is troubleshooting a recent OSPF stub configuration between R3 and R4. The only routes that should appear on the routing table for R4 are intra-area routes and the default route. However, interarea routes are also appearing.What must the administrator do to fix this problem?

Selecione uma ou mais das seguintes:

Issue the keyword stub on R3.
Issue the keyword no-summary on R3.
Issue the keyword nssa on R3.
Issue the keyword stub on R4.
Issue the keyword no-summary on R4.
Issue the keyword nssa on R4.

Explicação

Questão 20 de 60

A network administrator must interconnect a small office/home office (SOHO) in a modern metropolitan city. Which two access technologies would be the most cost effective solutions to implement? (Choose two.)

Selecione uma ou mais das seguintes:

cable
DSL
Frame Relay
leased lines
MPLS

Explicação

Questão 21 de 60

Which three features are commonly supported at the distribution layer of the Cisco hierarchical network model? (Choose three.)

Selecione uma ou mais das seguintes:

security policies
Power over Ethernet
switch port security
quality of service
Layer 3 functionality
end user access to network

Explicação

Questão 22 de 60

On an OSPF multiaccess network, which multicast address must a non-DR router use to send an LSU packet that contains new link-state information?

Selecione uma ou mais das seguintes:

224.0.0.1
224.0.0.2
224.0.0.5
224.0.0.6
224.0.0.9

Explicação

Questão 23 de 60

What is the best solution for the split-horizon problem in a Frame Relay network?

Selecione uma ou mais das seguintes:

disabling split horizon
using IGRP
using point-to-point subinterfaces
using floating static routes

Explicação

Questão 24 de 60

Refer to the exhibit. Which tunnel type should be configured on router R2 in order to establish connectivity between the two IPv6 islands?

Selecione uma ou mais das seguintes:

automatic 6to4 tunnel
automatic ISATAP tunnel
manually configured GRE tunnel
manually configured IPv6 over IPv4

Explicação

Questão 25 de 60

Refer to the exhibit. A two-way redistribution is configured on router R2 between the EIGRP and the OSPF domains. The
show ip route command output taken on R3 reveals that the network 10.10.10.16/28 is not installed in the routing table. What could the problem be?

Selecione uma ou mais das seguintes:

A
metric-type command is missing from the redistribution statement under OSPF routing process on R2.
A subnets command keyword is missing from the redistribution statement under the OSPF routing process on R2.
A summary-address command should be given under the OSPF routing process.
A no auto-summary command should be used under the EIGRP configuration on R2.
An area-range command should be used under the OSPF routing process.

Explicação

Questão 26 de 60

Refer to the exhibit. Routers A and B have EIGRP configured and automatic summarization has been disabled on both routers. Which two router commands should be used to summarize the attached routes, and to which interface is this command applied? (Choose two.)

Selecione uma ou mais das seguintes:

ip summary-address eigrp 1 192.168.10.64 255.255.255.192
ip area-range eigrp 1 192.168.10.80 255.255.255.224
summary-address 192.168.10.80 0.0.0.31
ip summary-address eigrp 1 192.168.10.64 0.0.0.63
serial interface on router A

Explicação

Questão 27 de 60

Refer to the exhibit. Assume router R2 does not have BGP enabled. However, the neighbor remote-as
router configuration command has been entered on routers R1 and R3. Based on the information that is presented, which two statements are true? (Choose two.)

Selecione uma ou mais das seguintes:

R1 will establish a peer relationship with R2 because they belong to the same BGP autonomous system.
R1 will establish a peer relationship with R3 because they have an IBGP session established.
R1 will establish a peer relationship with R2 although they do not have an IBGP session established.
R1 will establish a peer relationship with R3 although they are not directly connected.
R1 will establish a peer relationship with R2 because they are directly connected.

Explicação

Questão 28 de 60

Which two statements are true of policy-based routing (PBR) as a path control tool? (Choose two.)

Selecione uma ou mais das seguintes:

It is applied only in the inbound direction.
It can be applied only to link-state routing protocols.
Packets that do not match any match statements will be dropped.
It provides a mechanism to mark packets with different types of service (ToS).
Configured route map entries will have default sequence number increments of 5.

Explicação

Questão 29 de 60

A router has EIGRP configured as the only routing protocol. In what way does EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?

Selecione uma ou mais das seguintes:

It broadcasts hello packets to all routers in the network to re-establish neighbor adjacencies.
It sends queries to adjacent neighbors to find a new successor route.
It immediately sends its entire routing table to its neighbors.
It sets the metric for the failed route to zero.

Explicação

Questão 30 de 60

Refer to the exhibit. The route map LOAD_BALANCE has been applied to the FastEthernet interfaces of R1, and all interfaces are up. R1 uses two default static routes to reach the Internet via ISP1 and ISP2. Which traffic will be sent to the null 0 interface by the route map onR1?

Selecione uma ou mais das seguintes:

any packets that are sourced from the Internet
packets that are not sourced from the 10.2.0.0 network
packets that are not sourced from the ISP1 or ISP2 routers
packets that are sourced from the 10.2.0.0 network and destined for the Internet
packets that are sourced from 10.0.0.0 or 10.1.0.0 networks and destined for 10.2.0.0

Explicação

Questão 31 de 60

Which two statements are correct about redistribution? (Choose two.)

Selecione uma ou mais das seguintes:

The default-metric router configuration command takes precedence over the metric
metric-value option in the redistribute command.
The redistribute command is issued under the routing process that will send the redistributed routes.
When redistribution is occurring into OSPF, the optional subnets keyword specifies that subnetted routes should also be redistributed.
When redistributing into EIGRP, there are five parameters that encompass the metric value, although only four parameters are used to determine the metric.
Because of safeguards such as administrative distance, routing loops that are caused by redistribution are not possible.

Explicação

Questão 32 de 60

What are two effective ways to prevent the EIGRP stuck-in-active problem? (Choose two.)

Selecione uma ou mais das seguintes:

Modify keepalive timers on point-to-point connections.
Manually summarize routes wherever possible.
Configure core routers with SIA-Guard.
Configure distribution routers with SIA-Guard.
Set K-values to their default.
Maintain a hierarchical network design.

Explicação

Questão 33 de 60

What are two significant benefits that are provided by IPsec? (Choose two.)

Selecione uma ou mais das seguintes:

authentication
encryption
automatic creation of a public network
automatic creation of a private network
encapsulation

Explicação

Questão 34 de 60

Refer to the exhibit. An administrator is troubleshooting an adjacency problem between two OSPF routers. From the debug output, what is most likely the cause of the problem?

Selecione uma ou mais das seguintes:

The routers are using mismatched authentication passwords.
Router1 is using only simple password authentication.
The routers are using different MD5 key numbers.
The key types are mismatched on the routers.
The authentication methods do not match.

Explicação

Questão 35 de 60

Refer to the exhibit. Which set of features corresponds accurately to the Cisco Hierarchical Network Model as represented by the diagram?

Selecione uma ou mais das seguintes:

1. distribution - high speed switching
2. core - policy-based connectivity
3. access - local and remote workgroup
1. access - policy-based connectivity
2. distribution - high speed switching
3. core - local and remote workgroup
1. core - high speed switching
2. distribution - policy-based connectivity
3. access - local and remote workgroup
1. core - policy-based connectivity
2. distribution - high speed switching
3. access - local and remote workgroup
1. access - policy-based connectivity
2. core - local and remote workgroup
3. distribution - high speed switching
1. distribution - high speed switching
2. access - local and remote workgroup
3. core - policy-based connectivity

Explicação

Questão 36 de 60

What is typically deployed to support high-speed transmissions of data to SOHO cable modems?

Selecione uma ou mais das seguintes:

1000BASE-TX
DSL technology
fiber to the premises (FTTP)
high speed dialup cable modems
hybrid fiber-coaxial (HFC)

Explicação

Questão 37 de 60

Refer to the exhibit. RTA cannot establish an EBGP session with RTC in autonomous system 100. Which configuration command will fix the problem?

Selecione uma ou mais das seguintes:

The neighbor 3.3.3.1 remote-as 100 command should be applied on RTA.
The neighbor 1.1.1.2 remote-as 100 command should be applied on RTB.
The neighbor 3.3.3.1 ebgp-multihop command should be applied on RTA.
The neighbor 1.1.1.2 ebgp-multihop command should be applied on RTA.
The neighbor 1.1.1.2 ebgp-multihop command should be applied on RTB.

Explicação

Questão 38 de 60

Which three critical functions are provided by VPNs? (Choose three.)

Selecione uma ou mais das seguintes:

confidentiality of information
integrity of data
authorization of users
authentication of users
WAN management
quality of connection

Explicação

Questão 39 de 60

Refer to the exhibit. Which OSPFv3 configuration statement is true?

Selecione uma ou mais das seguintes:

The router ospf cost command should be issued under router configuration mode.
The ipv6 ospf 100 area 1 interface configuration command must be entered on interface Fa0/1 of routers R1 and R2.
The router-id command must be entered under each FastEthernet interface of routers R1 and R2.
The router-id command must be entered using an IPv6 address.

Explicação

Questão 40 de 60

What is a characteristic of an IBGP session type?

Selecione uma ou mais das seguintes:

Neighbors may be located anywhere within multiple autonomous systems, even several hops away from each other.
A session typically occurs between routers in different autonomous systems with multiple ISPs.
It can be established between routers in the same AS even if they are not link partners.
It occurs between routers in two different autonomous systems.

Explicação

Questão 41 de 60

Refer to the exhibit. Which two commands need to be used on R1 and R2 to create a virtual link to and from area 0? (Choose two.)

Selecione uma ou mais das seguintes:

R2(config-router)# area 0 virtual-link 1.1.1.1
R1(config-router)# area 0 virtual-link 2.2.2.2
R2(config-router)# area 5 virtual-link 1.1.1.1
R1(config-router)# area 5 virtual-link 2.2.2.2
R2(config-router)# area 7 virtual-link 1.1.1.1
R1(config-router)# area 7 virtual-link 2.2.2.2

Explicação

Questão 42 de 60

Refer to the exhibit. RTA, RTB, and RTC are connected through Frame Relay. RTA advertises network 180.80.0.0 to RTC with a next hop of 170.70.20.3. When RTC attempts to reach network 180.80.0.0, the routing fails. What should be configured under the BGP routing process to remedy the problem?

Selecione uma ou mais das seguintes:

RTA(config-router)# neighbor 170.70.20.3 next-hop-self
RTA(config-router)# neighbor 170.70.20.1 next-hop-self
RTB(config-router)# neighbor 170.70.20.1 next-hop-self
RTA(config-router)# bgp default local-preference 200
RTA(config-router)# neighbor 170.70.20.1 weight 2000
RTA(config-router)# neighbor 170.70.20.1 send-community

Explicação

Questão 43 de 60

Which two statements accurately describe the RIPng routing protocol? (Choose two.)

Selecione uma ou mais das seguintes:

RIPng forwards IPv6 broadcasts.
RIPng has a limit of 15 hops.
RIPng is a link-state routing protocol.
RIPng uses poison reverse.
RIPng uses UDP port 238 for updates.

Explicação

Questão 44 de 60

In the design of a network that will be based on the Cisco Enterprise Architecture, which two items would be included in the enterprise edge functional component? (Choose two.)

Selecione uma ou mais das seguintes:

internal web servers
core layer routers
VPN servers
a server farm
an intrusion detection system

Explicação

Questão 45 de 60

Refer to the exhibit. Router R1 is seeing routes that are advertised by router R2, and R2 is seeing routes that are advertised by R1. Which two statements are true when using EIGRP and an L3 MPLS VPN? (Choose two.)

Selecione uma ou mais das seguintes:

Router R1 has established an EIGRP neighbor relationship with router PE1.
Router R1 has established an EIGRP neighbor relationship with router PE2.
Router R1 has established an EIGRP neighbor relationship with router R2.
Router R2 has established an EIGRP neighbor relationship with router PE1.
Router R2 has established an EIGRP neighbor relationship with router PE2.
Router R2 has established an EIGRP neighbor relationship with router R1.

Explicação

Questão 46 de 60

Refer to the exhibit. After configuring the IPv6 manual tunnel, a network administrator tries to verify the configuration from R1. Which IPaddresses should be included in the extended
ping command in order to verify the status of the tunnel?

Selecione uma ou mais das seguintes:

Explicação

Questão 47 de 60

Multiple paths exist in the BGP table. Assuming the weights are the same, what will the next determining factor be?

Selecione uma ou mais das seguintes:

lowest MED
locally originated
shortest AS_Path
lowest origin type
highest local preference

Explicação

Questão 48 de 60

Which two variables must match between two OSPF routers to form a neighbor adjacency? (Choose two.)

Selecione uma ou mais das seguintes:

area IDs
K-values
process IDs
router priorities
hello and dead intervals

Explicação

Questão 49 de 60

When the command distribute-list 1 in serial 0/0 is used, which routing updates would be permitted?

Selecione uma ou mais das seguintes:

Routing updates that are received on any interface and permitted by ACL 1.
Routing updates that are received on serial 0/0 and permitted by ACL 1.
Routing updates that are received on any interface and permitted by prefix-list 1.
Routing updates that are received on serial 0/0 and permitted by prefix-list 1.
Routing updates that are received on any interface and permitted by route-map 1.
Routing updates that are received on serial 0/0 and permitted by route-map 1.

Explicação

Questão 50 de 60

Which two tasks should be conducted during the PPDIOO Prepare phase? (Choose two.)

Selecione uma ou mais das seguintes:

Develop an implementation plan.
Choose vendors and technical partners.
Establish organizational requirements.
Identify financial justification for upgrade.
Compare network performance with design goals.

Explicação

Questão 51 de 60

Refer to the diagram and configuration. OSPF is configured over Frame Relay using neighbor statements under router ospf mode. Although all PVCs are active, RTB and RTC do not see all OSPF routes in their routing tables. What could be done to fix this problem? (Choose two.)

Selecione uma ou mais das seguintes:

The frame-relay map statements on all routers should include the broadcast keyword.
The frame-relay map statements should be replaced by using the frame-relay interface-dlci command.
The priority value on the hub router should be set to 0.
The priority value on the spoke routers should be set to 0.
The ip ospf network non-broadcast command should be applied on each router.

Explicação

Questão 52 de 60

Which statement about stateless autoconfiguration is true?

Selecione uma ou mais das seguintes:

A host can autoconfigure itself by appending its MAC address to the local link prefix (64 bits).
Autoconfiguration allows devices to connect themselves to the network via IOS router DHCP services.
Autoconfiguration is well suited for devices such as servers and print servers.
During the autoconfiguration process, a router advertises the IPv6 64-bit prefix of its interface, and the host prepends this prefix toits modified EUI-64 formatted MAC address.
During the autoconfiguration process, the host sends a router advertisement, and the router replies with a router solicitation.

Explicação

Questão 53 de 60

Refer to the exhibit. R1 and R2 are unable to establish a BGP peer relationship. After a network administrator has confirmed that each router can ping the loopback interface of the other router, what can be done to fix this problem?

Selecione uma ou mais das seguintes:

Add a BGP network command for 4.1.1.0/24 on both routers.
Add the BGP no synchronization command on both routers.
Add the BGP neighbor ebgp-multihop 255 command on both routers.
Add the BGP neighbor update-source serial0 command on both routers.

Explicação

Questão 54 de 60

Which three statements are correct about the properties of an OSPF point-to-multipoint network type? (Choose three.)

Selecione uma ou mais das seguintes:

All routers can be configured as point-to-multipoint.
An OSPF point-to-multipoint network needs more PVCs because it requires a full-mesh topology.
All of the links between the routers are in the same IP subnet.
The DR/BDR is required and must be configured manually.
Cisco point-to-multipoint nonbroadcast mode neighbors must be statically defined.

Explicação

Questão 55 de 60

Which two OSPFv3 statements are true? (Choose two.)

Selecione uma ou mais das seguintes:

OSPF networks are configured under router configuration mode.
The multicast address FF02::6 is used to forward packets to the OSPF DR and BDR.
The router ID is configured using using an IPv4 address.
The router-id router-id command is issued in interface configuration mode.
The router ospf priority priority command is issued under the router configuration mode.

Explicação

Questão 56 de 60

Refer to the exhibit. A GRE tunnel must be configured between routers RTA and RTB. Assume that router RTB has been correctly configured. Which set of commands would correctly configure router RTA to encrypt traffic destined for router RTB?

Selecione uma ou mais das seguintes:

interface Tunnel0
tunnel source FastEthernet0
tunnel destination 172.16.3.1
interface Tunnel0
tunnel source FastEthernet0
tunnel destination 172.16.13.2
interface Tunnel0
tunnel source FastEthernet0
tunnel destination 192.168.23.3
interface Tunnel0
tunnel source Serial0
tunnel destination 172.16.3.1
interface Tunnel0
tunnel source Serial0
tunnel destination 172.16.13.2
interface Tunnel0
tunnel source Serial0
tunnel destination 192.168.23.3

Explicação

Questão 57 de 60

Refer to the exhibit. Assume all routers are running BGP sessions and both links are operational. Which procedure would ensure that AS1 routers use link 1.1.1.1 for packet transmittal to AS2?

Selecione uma ou mais das seguintes:

Set RTA local preference to 50 and other AS1 router local preference to 100.
Set RTA local preference to 100 and other AS1 router local preference to 50.
Set RTB local preference to 50 and other AS2 router local preference to 100.
Set RTB local preference to 100 and other AS2 router local preference to 50.

Explicação

Questão 58 de 60

What is a characteristic of ADSL?

Selecione uma ou mais das seguintes:

It is designed to deliver more bandwidth downstream than upstream.
It is designed to deliver more bandwidth upstream than downstream.
The upstream rate ranges from 1.5 to 9 Mb/s.
The downstream rates ranges from 16 to 640 Kb/s.

Explicação

Questão 59 de 60

Which two OSPF routing protocol characteristics can be used or modified at redistribution points to help implement a path control strategy? (Choose two.)

Selecione uma ou mais das seguintes:

metric
route tag
unequal cost load balancing
NSSA translation of Type 7 LSAs to Type 5 LSAs
process ID

Explicação

Questão 60 de 60

Which two networks would match the following prefix list? (Choose two.)
ip prefix-list MATCHTHIS seq 5 deny 10.1.0.0/16 ge 24 le 30

Selecione uma ou mais das seguintes:

10.0.0.0/16
10.0.0.0/24
10.1.0.0/16
10.1.0.0/24
10.1.1.0/30

Explicação

Verificar resposta

["https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625040/desktop_263bb41c-063b-4af4-8563-da7870bce573.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625051/desktop_27b4fab0-9aa4-4b61-aa91-69abb6e59e00.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625064/desktop_8edba50b-a976-4346-9dc5-967272206c8b.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625072/desktop_6508b8d3-1bf2-436e-93d8-174374828d56.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625078/desktop_4692dd10-5248-4d16-82a9-e9c61de0c695.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625084/desktop_f4d29495-f7ba-4cf5-bf89-dfa194d81bc7.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625091/desktop_1ca5c441-7acd-47b7-a26c-e57ac310d816.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625096/desktop_065e4811-085a-4d41-952d-954a8791960f.png","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625098/desktop_3a930ce2-bc72-4545-9a6f-49b49eb41055.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625113/desktop_b72baaa9-dadd-4097-9601-d6a5d6585927.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625128/desktop_d9d20fb2-a141-47bb-9d61-da5d19b2cf51.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625141/desktop_01be9b9a-bd76-4e1b-bc8e-c8afd256c673.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625157/desktop_fd3fd2d6-0f8a-493b-8a99-2a3ecb818912.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625163/desktop_3ed78e45-a16e-4f0f-9fa3-d8eb7bc4676c.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625182/desktop_79653b3c-9eac-476f-bfa7-e2fab8bffb3e.png","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625220/desktop_cba6298e-97de-4fef-8c80-07174733cc95.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625236/desktop_34dd6f9a-d2b0-4f16-a78d-4bb8abe8c379.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625276/desktop_54cfdbcd-a886-4f66-b2d6-52f8110239f4.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625296/desktop_0a2bd611-eb57-4dae-b869-ca3d426d2516.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625311/desktop_3aea44f0-d3d8-4490-9030-53c33641469d.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625322/desktop_e1b06807-a2cd-4325-8116-b1d84f721b32.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625339/desktop_a1cd72e6-87f3-492e-9b23-b0ff89c90c19.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625355/desktop_5a4d540e-cfcc-4110-893a-7307b64d9d72.png","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625401/desktop_5bddd22c-3b23-41f7-ad3c-7ec4b2339d11.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625412/desktop_53dca292-2b6f-4191-bddb-eeda8c28e85a.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625578/desktop_687dccfa-2ae6-4229-8013-5cceb2186eb1.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/checkbox_question/image/2625590/desktop_2449b0cb-9ba5-46ed-8b7e-b2b9968374b2.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/quiz_answer/image/6909655/desktop_606fca86-4181-4041-8a8b-678eae3d9d0d.png","https://examtimeassets.s3.amazonaws.com/uploads/quiz_answer/image/6909656/desktop_833efec2-4662-4274-9ab7-9ae1f5dfa3ad.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/quiz_answer/image/6909657/desktop_9f2c6f42-4e0d-4a9c-9289-7c4243189b16.jpeg","https://examtimeassets.s3.amazonaws.com/uploads/quiz_answer/image/6909658/desktop_1820a1fb-6d99-4902-a966-d8ba96fdc94a.jpeg"]

	Criado por amandeep.purewal mais de 10 anos atrás

Quiz sobre CCNP Route, criado por amandeep.purewal em 05-03-2016.

CCNP Route

Questão 1 de 60

How do EIGRP routers establish and maintain neighbor relationships?

Selecione uma ou mais das seguintes:

Explicação

Questão 2 de 60

The IPv6 autoconfiguration feature enables a PC to automatically connect to an IPv6 network. What type of IPv6 address allows a PChost to send a router solicitation message requesting a prefix for stateless autoconfiguration?

Selecione uma ou mais das seguintes:

Explicação

Questão 3 de 60

During an interview, the company IT manager mentions that the company has two critical communication links to its main supplier. These links require an uptime of 24/7. Which part of the PPDIOO process is most affected by this information?

Selecione uma ou mais das seguintes:

Explicação

Questão 4 de 60

Refer to the exhibit. The RIP routes must be injected into the OSPF domain. Which command will perform external route summarization?

Selecione uma ou mais das seguintes:

Explicação

Questão 5 de 60

Selecione uma ou mais das seguintes:

Explicação

Questão 6 de 60

How does OSPF exchange routing updates when the passive -interface command is applied?

Selecione uma ou mais das seguintes:

Explicação

Questão 7 de 60

Which functional component of the Cisco Enterprise Architecture is responsible for hosting internal servers?

Selecione uma ou mais das seguintes:

Explicação

Questão 8 de 60

Refer to the exhibit. A network administrator has configured EIGRP authentication between routers R1 and R2. After the routing tables are reviewed, it is noted that neither router is receiving EIGRP updates. What is a possible cause for this failure?

Selecione uma ou mais das seguintes:

Explicação

Questão 9 de 60

Refer to the exhibit. A GRE tunnel must be configured between routers RTA and RTB. Assume that router RTB has been correctly configured. Which command would correctly configure router RTA to encrypt traffic that is destined for router RTB?

Selecione uma ou mais das seguintes:

Explicação

Questão 10 de 60

What does the log message %DUAL-3-SIA: Route 10.1.2.0/24 stuck in active state in IP-EIGRP 24 mean?

Selecione uma ou mais das seguintes:

Explicação

Questão 11 de 60

Refer to the exhibit. Which route redistribution statement is true?

Selecione uma ou mais das seguintes:

Explicação

Questão 12 de 60

Which access technology would be the most insecure to use when interconnecting a branch site?

Selecione uma ou mais das seguintes:

Explicação

Questão 13 de 60

Selecione uma ou mais das seguintes:

Explicação

Questão 14 de 60

Refer to the exhibit. How is the OSPF default gateway entry determined for R2?

Selecione uma ou mais das seguintes:

Explicação

Questão 15 de 60

Refer to the exhibit. OSPF and OSPFv3 have been configured on routers R1 and R2. However, they can exchange routing updates for OSPF but not for OSPFv3. What additional step should be taken to remedy the problem?

Selecione uma ou mais das seguintes:

Explicação

Questão 16 de 60

Refer to the exhibit. Based on the configuration in the exhibit, which statement is true?

Selecione uma ou mais das seguintes:

Explicação

Questão 17 de 60

When would the network administrator use the ip bandwidth -percent eigrp as-number percent command?

Selecione uma ou mais das seguintes:

Explicação

Questão 18 de 60

Which two EIGRP and MPLS implementation statements are true? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 19 de 60

Selecione uma ou mais das seguintes:

Explicação

Questão 20 de 60

A network administrator must interconnect a small office/home office (SOHO) in a modern metropolitan city. Which two access technologies would be the most cost effective solutions to implement? (Choose two.)

Selecione uma ou mais das seguintes:

Explicação

Questão 21 de 60

Refer to the exhibit. A two-way redistribution is configured on router R2 between the EIGRP and the OSPF domains. The
show ip route command output taken on R3 reveals that the network 10.10.10.16/28 is not installed in the routing table. What could the problem be?

Refer to the exhibit. Assume router R2 does not have BGP enabled. However, the neighbor remote-as
router configuration command has been entered on routers R1 and R3. Based on the information that is presented, which two statements are true? (Choose two.)