Quiz
Bank of questions Health and Safety
Perguntas do quiz (157)
1 BS 7671, the IEE Wiring Regulations, are:
- Anon-statutory
- Bcode of practice.
- Cstatutory
- Dhealth and safety guidance notes
2The colour and voltage to be used for powertools on a construction sites is?
- ABlue = 400V
- BRed = 230 V
- CYellow = 110 V
- Dd White = 25 V
3Which of the following does not have a duty placed upon them by the Electricity at Work Regulation 1989?
- AEmployee
- BEmployer
- CHouseholder
- DSelf-employed
4The safe use of electricity on site is covered by which Regulation?
- AElectricity at Work Regulations 1988
- BElectricity at Work Regulations 1989
- CElectricity at Work Regulations 1990
- DElectricity at Work Regulations 1991
5Electricity on site is normally at a reduced voltage, which reduced voltage is found on site?
- A24 Volts.
- B110 Volts.
- C400 Volts.
- D230 Volts
6When carrying out electricity site safety on tools, checks are carried out on all of the following except which one?
- ACheck the supply frequency.
- BCheck that RCD protection is provided where necessary.
- CCheck for current PAT labels.
- DPower tools should be double insulated.
7Which of the following facilities are not necessary with regards to welfare?
- AA supply of clean drinking water.
- BSuitable toilets.
- CA supply of hot and cold water soap and towels.
- DA supply of tea and coffee.
8Which of the following is necessary to minimise the risk of fire on a construction site?
- AEmployment of fully trained fire fighting staff.
- BMeans to give warning of fire
- C Constant supply of running water
- DEnsure the electrical supply is isolated at all times
9What is the purpose of the Electricity at Work Regulations 1989?
- ATo make you read textbooks.
- BTo prevent tools from being stolen.
- CTo prevent risk of death from electricity at work activities.
- DTo prevent you from taking unpaid sick leave.
10What does the term non-statutory mean?
- ANot enforceable by employers
- BEnforceable by employers.
- CNot enforceable by law
- DEnforceable by law.
11The use of barrier cream during and after work activities can help prevent?
- APaint on your skin
- BBroken fingernails
- CDermatitis
- DArthritis
12Which of the following is a necessary check before using electrical equipment?
- ACheck the tool is the correct colour
- BCheck the cable is not frayed or damaged
- CEnsure the flex is brown
- DCheck the brand of the tool
13To check a circuit is isolated and safe to work on you must?
- ACheck with a reliable voltage indicator
- BWet your finger and 'flash' test the conductor.
- CCheck it with a home made lamp and flex
- DGet somebody else to check it
14To check a circuit is isolated and safe to work on you should?
- AGet somebody else to check it
- BCheck it with a home made lamp and flex
- CWet your finger and 'flash' test the conductor.
- DCheck with a GS38 voltage indicator
15Which of the following would not be a necessary safety check on a ladder?
- ANo dirt on rungs.
- BNo damage to toe boards.
- CNo splits in rungs
- DNo damage to tie-rods
16What is the correct angle that a ladder should be in relation to the ground?
- A65°
- B75°.
- C55°
- D45°
17When a ladder provides access to a working platform how much of the ladder must extend above the landing place?
- A3 rungs.
- B4 rungs.
- C5 rungs.
- D6 rungs.
18The two long sections of a ladder, which hold the rungs together, are known as?
- AToe boards.
- BScaffold boards
- CStyles
- DTie rods
19Which of the following should have toe boards fitted?
- AMoving escalator.
- BA ladder
- CMobile scaffold
- DTrestle scaffold
20All the following are important considerations before lifting a load except?
- AMaking trial lifts on similar loads.
- BChecking the load for any sharp edges
- CChecking that doors are opened if you have to carry the load through them.
- DGetting help if the load is too heavy.
21When dealing with a fire in an open warehouse full of card board, which one of the following extinguisher would be most suitable?
- AWater
- BBCF Halon
- CFoam
- DCarbon Dioxide
22The RIDDOR Regulations requires your company to inform the enforcing authority without delay of the following circumstances except?
- AAny major injuries to employees.
- BAny fatal injuries.
- CThe overturning of a crane.
- DAn accident at home.
23The three elements that all fires require are?
- AFuel, heat and paper.
- BFuel, air and oxygen
- CFuel, air and heat.
- DHeat, air and oxygen
24If you discover a fire which is the correct sequence that should be carried out?
1. Call the fire service.
2. Raise the alarm.
3. Leave by the nearest exit.
4. Do not re-enter building unless advised by the fire marshall.- A3, 2, 1, 4
- B3, 2, 4, 1
- C2, 1, 3, 4
- D2, 3, 1, 4
25European legislation requires fire extinguishers to be a certain colour no matter what their intended use. What is this colour?
- ASilver
- BRed
- CCream
- DBlack
26On an accident report form which one of the following is not required?
- ADate of accident.
- BHome address of the victim's parents
- CLocation of accident.
- DName of injured person.
27Which of the following types of fire extinguisher must be used on live electrical equipment if there is a fire?
- AWater type.
- BSprinkler system
- CFoam
- DCarbon dioxide.
28 If you had to deal with an emergency i.e. chemical spill, what should your first action be?
- ASneak away without informing anybody.
- BInform the local newspaper.
- CDial the emergency service number in a safe environment.
- DInform your parents.
29The ABC of resuscitation stands for?
- AAccident, Bleeding, Causality
- BAirways, Breathing, Circulation
- C Accident, Breathing, Causality
- DAirways, Breaks, Circulation
30The first action you should think of in the event of an electric shock to a colleague is?
- AIsolate the supply.
- BRemove the plug.
- CCheck for your own safety.
- DGet help.
31If the casualty is currently suffering from an electric shock and you can not break the electrical supply by pulling a plug or switching off a supply what would be a good material for breaking the contact between casualty and supply?
- AUse a piece of metal trunking
- BUse a wooden broom handle.
- CUse your bare hands.
- DUse a piece of metal conduit.
32How would it be best to check the casualty's response if they were unconscious?
- APinch them hard on the arm.
- BSlap them hard on the face.
- CTalk to them and gently shake the casualty.
- DAsk somebody else if they knew their name.
33If the casualty was unconscious and lying on the floor what should you check for next?
- ABreathing
- BBleeding.
- CPulse.
- DColour of skin.
34What is the correct immediate treatment for a burn?
- ATreat for shock.
- BFlood the burn with cold water.
- CCheck for pulse.
- DRemove clothing.
35The abbreviation COSHH means?
- AControl of oxidising substances hazardous to health.
- BControl of oxidising substances harmful to health.
- CControl of substances harmful to health.
- DControl of substances hazardous to health
36Asbestos dust can become a health hazard if it is?
- AWashed from clothing.
- BInhaled into the lungs
- CVacuumed away.
- DContained by protective clothing.
37Which of the following is not covered be the HASAWA 1974?
- ADomestic servants.
- BEmployers.
- CApprentices at college
- DThe self-employed
38Under the HASAWA 1974 employers have duties to their employees which of the following is not a duty of an employer?
- AThe employer must provide JIB rates of overtime payment.
- BThe employer must provide safety information.
- CThe employer must provide safety training
- DThey must maintain plant and machinery in a safe condition
39As an employee you have responsibilities under the HASAWA 1974 which of the following is not a responsibility?
- ABringing to your employer's attention any situation you consider dangerous.
- BCo-operate with your employer on safety matters.
- CDo not recklessly interfere with anything provided for your safety
- DInforming to your employer on people who leave early
40The Electricity at Work Regulations 1989 imposes general health and safety requirements on all the following except?
- ASchool children.
- BEmployees.
- CSelf-employed.
- DEmployers.
41On a construction site a safety helmet must be worn by everyone except where?
- A When guard rails and toe boards are fitted to scaffolding
- BThe building work is not over 10m high
- CAttendance on site is for less than half an hour.
- DA meeting held in a site hut.
42The minimum heights at which guardrails and toe boards must be fitted to tower scaffolds is?
- A4m
- B5m.
- C3m
- D2m
43It is the duty of all employees under the Health and Safety at Work Act to:
- Alook after their own safety only
- Blook after the safety of themselves and of colleagues around them
- Cinstruct other workers on safety matters
- Dwork independently
44British Standards, B.S. 7671 are:
- Apart of the Electricity at Work regulations
- Bhave been replaced by IEE Wiring regulations
- Cnon-statutory regulations
- Dstatutory regulations
45It is the responsibility of all employers to ensure that the workplace is:
- Asafe without risk to health
- Bwarm and comfortable to work in
- Calways clean and tidy
- Dinspected every day to identify hazards
46Where personal protective equipment (P.P.E.) is required to perform a task in the workplace, the P.P.E. must be provided by:
- Athe employee and paid for by the employer
- Bthe employee
- Cthe employer and paid for by the employee
- Dthe employer
47The main legislation concerned with the safe use of chemicals in the workplace is:
- AThe Chemicals (Hazard Information and Packaging for Supply) Regulations
- BThe Environment Protection Act
- CThe Control of Substances Hazardous to Health Regulation (COSHH)
- DThe Consumer Protection Act
48In terms of fire precautions it is the responsibility of the employer to ensure that:
- Adaily inspections are made to ensure that there are no fire risks
- Ball materials used in the workplace are non-flammable
- Cadequate means of escape and fire fighting are provided
- Dall work areas are fireproof
49It is the responsibility of an employee who identifies a safety hazard in the workplace to:
- Areport the hazard to the supervisor
- Bleave the premises and inform others to do the same
- Cavoid the hazard and carry on working
- Dreport the hazard to the local health authority
50When working in a workshop where dust is present and employee should wear
- Adisposable overalls
- Bdisposable respirator
- Ccape hood
- Dface screen
51An electrical installation need to be isolated from the supply before carrying out workon the installation in order to prevent
- Adamage to cables and components
- Binterruption of the local supply system
- Cpossible electric shock
- Ddamage to appliances
52The Reporting of Injuries, Diseases and Dangerous Occurrences Regulations must be applied in the event of accidents in the workplace causing:
- Aminor injuries to the face
- Bmajor injuries
- Cany injury to all
- Dfractures to fingers
53The first action to be taken if a person is found lying unconscious on the floor after receiving an electric shock is to:
- Acheck for broken bones
- Btelephone for assistance
- Ccheck for pulse and breathing
- D check for cuts and bleeding
54A dry powder fire extinguisher has a red body with an identifying band which is:
- Ablue
- Bred
- Cgreen
- Dwhite
55Trades and employer associations within the electrical industry are responsible for
- Ainspecting all completed installation work
- Bfinding employment for redundant workers
- Cpreparing statutory regulations for the industry
- Dmaintaining standards within the industry
56The term BSEN found on most products refers to
- ABritish Standard Electrified Natural
- BBritish Standard Empowered Norm
- CBritish Standard European Norm
- DBritish Standard Electrical Nomenclature
57The Health and Safety at Work Act come into force in
- A1972
- B1973
- C1974
- D1975
58All of the following statements are true about using podium steps EXCEPT?
- APodiums can topple over so you must take care when reaching sideways
- BLike all other equipment podiums must be inspected regularly
- CPodiums are 100% safe and cannot topple over
- DYou must ensure the wheels are locked before getting on
59What is the leading cause of death among construction workers?
- AElectrocution
- BFalling from height
- CLeptospirosis
- DBeing hit by vehicles on site
60Which of these statements is true about using ladders?
- ATwo people can work on the same ladder only if someone else holds the ladder
- BTwo people can work on the same ladder if the supervisor approves
- CTwo people can work on the same ladder if it is long enough
- DOnly one person should work on a ladder
61What should you do if the ladder you’re about to use is damaged?
- AStop using it, report it and let your colleagues know the ladder is not safe
- BPut the ladder in a corner and leave it there
- CTry to fix the ladder yourself
- DCarry on using the ladder but stay away from the damaged section
62What should you do if you need to use a mobile tower scaffold but the wheel brakes are not working?
- ADo not use it
- BUse a rock or a piece of wood to wedge the wheels and stop them from moving
- CCarry on using it only if the floor is level
- DAsk a colleague to hold the tower while you work
63Ladders should never be painted because:
- AThe paint could cause a distraction to the person using the ladder
- BYou will need to repaint the ladder regularly
- CThe paint can hide or mask damaged parts of the ladder
- DThe paint causes the ladder to become slippery
64The best way to ensure a ladder is secured and won’t slip is to
- ATie it at the bottom
- BTie it at the top
- CHave a colleague hold it while you work
- DUse a piece of wood to wedge the bottom
65Which of these best describes working at height?
- A10m above the ground
- BAny height above or below ground level that can cause an injury if you fall
- C6m above the ground
- D5m above the ground
66How many points of contact should you have with a ladder at all times?
- A2
- B3
- C1
- D4
67Checking a ladder before use should be done by?
- AThe site manager
- BThe person about to use it
- CYour health and safety rep
- DYour supervisor
68High levels of dust can be inhaled when performing tasks such as grinding, drilling, sanding and cutting. These levels are most dangerous when
- AUsing the tool outside when it is windy.
- BWorking outdoor on a calm day.
- CUsing the tool in a large, indoor area.
- DWorking in a small room.
69You need to sweep up dust that was created during your shift. You should:
- AAll of the above.
- BDampen down the area.
- CEnsure that there has adequate ventilation.
- DPlace a protective mask over your nose and mouth.
70You are required to undertake some work that will produce dust. What will you need to do?
- AAvoid the work, as dust can harm your respiratory system.
- BBegin work immediately; dust is hardly dangerous.
- COnly work for a short period of time.
- DWear the correct personal protective equipment (PPE) and use devices that will control airborne dust.
71What TWO methods can you use to reduce the amount of dust from becoming airborne?
- AWet cutting and place a dust collector on the machine.
- BWork carefully and slowly.
- CKeep your area neat and tools in the correct place
- DWear a protective mask and a hard hat
72When using a power tool for cutting and grinding, why is it important for the dust to be collected?
- AThe tool performs better if dust is collected.
- BDust can be harmful if it is inhaled.
- CA machine guard is not necessary if the dust is collected.
- DIt will save time and avoid a mess.
73Being exposed to which of these items will NOT cause lung infections or diseases?
- ASilica in dust form
- BAsbestos fibres.
- CStrong odours.
- DBird faeces.
74You are working with a chemical and require respiratory protective equipment (RPE). If none has been given, what do you do?
- AWork as quickly as possible.
- BSmell the chemical to determine whether it is dangerous.
- CBegin work but take breaks at five-minute intervals.
- DDo not work until the proper equipment and training have been provided.
75Solvents in paints and resins can lead to:
- AAll of the following.
- BOther effects on the body.
- CHeadaches, nausea and dizziness.
- DLung issues.
76You’ve received a new pair of safety boots within the last month, if it gets damaged during the next month how long do you need to wait before you can request a new one?
- A Request another pair immediately
- B3 Months later
- C2 Months later
- D1 Month later
77In accordance with the Electricity at Work regulations, when considering whether to work live a responsible person should:
- Ado as the client demands
- B only work live
- Conly work dead
- Dcarry out a risk assessment
78Test instruments used for working on electrical systems should:
- Ahave insulated test probes
- Bhave non-insulated test probes
- Cbe less than 10 years old
- Dbe yellow in colour
79Under the Electricity at Work Regulations, live working is considered:
- Anever to be allowed
- Bonly to be allowed in exceptional circumstances
- Cto be normally permitted
- Das entirely acceptable
80To prove a circuit or equipment is dead after isolation what is the FIRST activity in the sequence of events?
- ACheck that the voltage detector is working on a proving device, known live source or in-built test feature
- BCheck between line and neutral
- CCheck between line and earth
- DMake sure equipment is not working
81The nominal single phase voltage in the UK is?
- A400 volts
- B415 volts
- C240 volts
- D230 volts
82When is live working permissible?
- AWhen the person carrying out the work is a competent person
- BWhen it is unreasonable in all circumstances for the equipment to be made dead and suitable precautions are taken
- CWhen the means of isolation cannot be identified
- DWhen the person working on the equipment is wearing rubber gloves
83Which of the following is not a requirement of low voltage safe isolation practice?
- AThe conductors are proved to be dead at the point of work
- BEnsuring that the correct point of isolation is identified
- CThe person carrying out the work is issued with insulating gloves
- DA caution notice should be applied at the point of isolation
84The specific effects on the human body of a major electric shock are one of the following:
- Abroken bones
- Bchest pains
- Cburns and cardiac arrest
- Ddermatitis
85The lowest level of electrical current which can harm the human body is normally measured in:
- Amicroamps
- Bkiloamps
- Camps
- Dmilliamps
86Where mains voltage is used to supply portable equipment on a construction site, what additional protection is required?
- ACable avoidance tool
- BResidual current device (RCD)
- CStep-down generator
- DStep-down transformer
87What colour cable USUALLY signifies 110 volt power supply on site?
- AYellow
- BBlue
- CRed
- DBlack
88A portable electric generator on site has two power outlets, 110 volts and 230 volts. What colour would the 110 volt outlet be?
- ARed
- BBlue
- CYellow
- DBlack
89The maximum AC voltage which the human body can withstand without long term physiological effects in dry conditions is:
- A230 volts
- B400 volts
- C50 volts
- D110 volts
90Which of the following statements is true with regard to the dangers of electricity?
- AElectricity is dangerous at any time because you cannot tell by looking at a cable whether or not it is live
- BElectricity is only dangerous in wet weather
- CElectricity is only dangerous if you are not wearing wellington boots
- DElectricity is perfectly safe so long as you wear cotton gloves
91What is the most serious effect that electric shock can have if you come into contact with a live part?
- Aelectric current can cause the finger muscles to twitch
- BThe electric current can cause the heart to stop, resulting in death
- CThe electric current can cause burn marks on the fingers
- DThe electric current can cause a slight tingling in the fingers
92Your job involves you working near to hanging electrical cables which have bare ends. What should you do?
- AAttempt to push the cables back into the ceiling void so that you can start work
- BInform your supervisor and keep well away
- CCarry on working, as there shouldn't be a problem
- DTouch the cables to see if they are live
93For all live working activities it is necessary to:
- Akeep your fingers crossed
- Bbe accompanied
- Cwear rubber gloves only
- Dcarry out a risk assessment as required by the EAW Regulations.
94An electrical Permit to Work is primarily a statement that:
- Acertain instructions need to be followed
- Bthe circuit or equipment has been isolated and is safe to work on
- Cthe circuit or equipment is live
- Dsomeone else has taken responsibility for the work
95The probes of voltage detectors and test instruments used on electrical systems should be:
- Acoloured red
- Bshaped or have barriers to prevent finger contact with the tips
- Caccompanied by a calibration certificate
- Dmanufactured in the UK
96which of the following should be used to prove a circuit or equipment is dead after isolation?
- AA voltage stick
- BA multimeter
- CA proprietary test lamp or two-pole voltage detector
- DA lamp holder with a length of flex attached
97Identify one method of enforcing regulations that are available to the Health and Safety Executive:
- AHealth Notice
- BIncreasing insurance premiums
- CImprovement Notice
- DObstruction Notice
98What happens if a Prohibition Notice is issued by an Inspector of the local authority or the HSE?
- AThe work that is subject to the notice must cease
- BThe work can continue, provided a risk assessment is carried out
- CThe work can continue if adequate safety precautions are put in place
- DThe work in hand can be completed, but no new work started
99A Health and Safety Executive Inspector can?
- AOnly visit if they have made an appointment
- BOnly visit to interview the site manager
- COnly visit if accompanied by the principal contractor
- DVisit at any time
100If a Health and Safety Executive Inspector issues a “Prohibition Notice”, this means that:
- Athe HSE must supervise all work from then on
- Bthe HSE must supervise the work covered by the notice
- Cspecific work activities, highlighted on the notice, must stop
- Dthe HSE must notify the police and force penalties
101Employers are required to provide information to their employees on their health and safety rights and responsibilities and how to get advice by:
- ATelling them verbally when they start work for them
- BDisplaying a poster or giving them leaflets approved by the HSE
- CMaking them read the company health and safety policy
- DE-mailing the information to them
102Employers have to produce a written Health and Safety Policy statement when:
- AA contract commences
- BThe HSE notifies them
- CThe safety representative requests it
- DThey employ five people or more
103What do the letters HSE stand for?
- AHealth and Safety Executive
- BHealth and Safety Examiner
- CHealth and Safety Exercise
- DHighly Safe Electrician
104The Health and Safety Executive is:
- AThe jury in health and safety court cases
- BPart of the police force
- CThe regulatory body for the promotion of health and safety at work
- DPart of the National Health Service
105The Health and Safety at Work Act requires employers to provide what for their employees?
- ASuitable transport to work
- BA safe place of work
- CPayment for work done
- DAdequate rest periods
106The Health and Safety at Work Act 1974 and any regulations made under the Act are:
- ANot compulsory, but should be complied with if convenient
- BAdvisory to companies and individuals
- CPractical advice for the employer to follow
- DLegally binding
107Regulations that govern health and safety on construction sites:
- Aare mandatory
- Bapply only to large companies
- Cdo not apply during ’out of hours’ working
- Dapply only to inexperienced workers
108Which of the following statements is correct?
- AOnly the client is responsible for safety on site
- BEmployees have no responsibility for Health and Safety on site
- CAll employees must take reasonable care, not only to protect themselves but also their colleagues
- DThe duty for health and safety falls only on the employer
109Which of the following is correct for risk assessment?
- AOnly required on major jobs
- BMust always be done
- COnly required to be done for hazardous work
- DIt is a good idea but not essential
110In the context of a risk assessment, what do you understand by the term risk?
- AThe likelihood that harm from a particular hazard will occur
- BAny work activity that can be described as dangerous
- CSomething with the potential to cause injury
- DAn unsafe act or condition
111Who would you expect to carry out a risk assessment on your working site?
- AA competent person
- BThe construction project designer
- CA visiting HSE Inspector
- DThe CDM Co-ordinator
112What must be done before any work begins?
- AGeological survey
- BSoil assessment
- CAssessment of risk
- DEmergency plan
113Complete the following sentence: A risk assessment
- Aisn’t particularly useful
- Bis a means of analysing what might go wrong
- Cprevents accidents
- Dis a piece of paper required by law
114Why would your supervisor ask you to read the method statement and risk assessment before you start your next job?
- AAs someone has taken the time and trouble to write them, you might as well read them
- BThe supervisor wouldn’t, they thinks they are a waste of time
- CThey contain information on how to carry out the job in a safe manner
- DThey thinks you have got nothing better to do
115Why should regular inspections of the workplace take place?
- ATo prepare for a visit from an HSE Inspector
- BTo check that everyone is doing their job
- CTo check that all employees are present
- DTo check whether the working environment is safe
116If there is a risk of injury from lifting loads what should you think about first?
- AHow to lift the load
- BWhere to hold the load when lifting
- CWhat the weight of the load is
- DWhether the load needs to be lifted at all
117Before performing manual lifting what is the first thing you should do?
- AKick it to see if it is stable
- BAssess the whole task
- CWeigh the article
- DCheck the headroom
118What should you do if your supervisor asks you to move something that you find is too heavy to lift?
- AGet a forklift truck or lifting tackle
- BInform your supervisor that it is too heavy
- CAsk your mates to assist in the lift
- DGive it a try using correct lifting methods
119What would you NOT consider in making a judgement of the risks from a load?
- AIts centre of gravity
- BIts weight
- CIts colour
- DIts size and condition
120Where a load has to be lifted manually, what is the employer required to do by law?
- AAssess the time the job will take
- BAssess the risk of the task
- CDetermine the number of people required
- DCalculate the cost of the exercise
121Which of the following is advisable when lifting a load manually?
- AKeep legs and back straight, use power of legs
- BBend the knees, keep the back as straight as possible, use power of legs
- CBend the knees, keep the back straight, use power of back
- DKeep legs straight, bend back, use power of legs
122In manual handling, which of the following general statements is true?
- ALoads should be held at arm’s length while carrying
- BLarge loads should be broken down into smaller loads where possible
- CAnyone can carry any load as long as they are strong enough
- DYou should keep your back bent when lifting
123Where there has been a major change in a manual handling operation, what should the employer do?
- AMonitor the operation being undertaken
- BReview the number of people involved
- CReview the original risk assessment
- DMonitor the cost of change
124When picking up an object, you should:
- Abend your knees
- Bwear a back brace
- Cbend your back
- Dbend your arms
125When an article has to be moved for a long distance, you should:
- ACarry it all the way
- BDrag it all the way
- CGet someone else to do it for you
- DUse a barrow or trolley
126If a load has an uneven centre of gravity, how should you lift it?
- AKeep the heaviest side of the load on the weakest arm
- BKeep the heaviest side of the load towards you
- CKeep the heaviest side of the load on the strongest arm
- DKeep the heaviest side of the load away from you
127Why should a serious accident be reported to the enforcing authority?
- ASo that the company will be held responsible
- BSo that the site manager can see who is to blame
- CIt is a legal requirement
- DIt helps the site find out what caused it
128Which of the following should be recorded in the accident book following an accident?
- AYour National Insurance Number
- BThe weather conditions
- CThe date and time the accident occurred
- DYour date of birth
129Which one of the following accounts for most accidents each year on construction sites?
- ASlips, trips and falls
- BTrench collapses
- CElectrocution
- DStrikes by moving vehicles
130Which one of the following is classed as a reportable occupational disease under RIDDOR?
- AAmputation
- BInfluenza
- CAsbestosis
- DMental disorder
131Why is it important to report ’near miss’ accidents to your employer?
- ASo that someone can be disciplined
- BSo lessons can be learned, preventing an accident next time
- CTo make the figures look good
- DIt’s the law
132What action should you take if you discover a fire?
- AExtinguish the fire without raising the alarm
- BCarry on working if it is safe to do so
- CRaise the alarm
- DLeave it because you will get the blame
133If you discover a fire at work, what should you do first:
- Araise the alarm and warn fellow workers
- Brun around looking for an alarm to sound
- Cuse a fire extinguisher to put it out
- Dtelephone 999
134What is a fire assembly point?
- AThe place where the fire alarm is
- BA place where fire extinguishers are kept
- CA place where the fire brigade goes to
- DThe place to go when the fire alarm sounds
135All new fire extinguishers are coloured red or of bright self-coloured metal. How do you know the difference between types?
- AThe weight and shape of the extinguisher
- BThe type of extinguisher is written on a sign next to it
- CDuring site induction, you will be told where the different types of extinguishers are
- DA different colour panel or band is on the body of the extinguishers
136A black-labelled fire extinguisher contains:
- ACarbon dioxide
- BFoam
- CWater
- DDry powder
137What is a blue-labelled fire extinguisher filled with?
- ACarbon Dioxide
- BDry powder
- CFoam
- DWater
138Which types of fire extinguishers should be used on electrical fires?
- AFoam and water
- BCarbon dioxide and dry powder
- CDry powder and foam
- DWater and carbon dioxide
139A workmate burns their hand on a piece of very hot metal. What should you do first?
- APut their hand in cold water if it is available
- BWarn other people about the piece of hot metal
- CCover the burn with something dry
- DRub some cream or Vaseline into the burn
140Which of the following items should not be in a first-aid box?
- ATriangular bandages
- BDisposable gloves
- CPain killers
- DSafety pins
141Which of the following must an employer consider when making provisions for first aid?
- AHow much working space will be wasted
- BHow much will it cost
- CWhether the local ambulance service can be used
- DThe likely types of injury
142On a mobile elevating work platform, what should you attach your safety harness to?
- AA nearby pipe or scaffold
- BThe boom of the machine
- CA strong part of the structure you are working on
- DA secure anchorage point inside the platform
143You have been asked to operate a cherry-picker (mobile elevated work platform) when it is very windy. What should your FIRST consideration be?
- ATie all light-weight objects to the hand-rails of the basket
- BWear an extra layer of clothing to keep warm
- CDoes the wind-speed make it unsafe to use the machine
- DWear a safety harness and clip it to the structure that you are working on
144When working on a roof that has fragile, clear-plastic panels, what is the best way of preventing falls through the panels?
- AMake sure that everyone is told where the panels are and to avoid treading on them
- BCover the fragile panels with a strong material and secure the covers to stop them being dislodged
- CRemove the panels carefully to leave an open space-
- DIt shouldn’t be necessary to do anything, everyone knows the dangers
145When working on fragile roofs:
- Acrawling boards should always be used
- Bas long as you avoid any fragile areas it is safe
- Cwalk straight across the roof to where you need to get to
- Dit is safe to walk on the purlins
146Under what circumstances do the Work at Height Regulations permit a stepladder to be used on site?
- ANever – stepladders are banned
- BAt any time
- CProvided you can’t fall 2 metres or more
- DOnly when a risk assessment shows that safer alternatives have been ruled out and the task is of low risk and of short duration
147What is the recommended maximum voltage for portable hand lamps when working in confined or damp locations?
- A400 volts
- B230 volts
- C110 volts
- D50 volts
148Why may a confined space be dangerous to work in?
- AAll of the hazards mentioned
- BTemperature and poor ventilation may affect the worker
- CAir in the space may be unbreathable due to poisonous gas
- DThere may not be sufficient working space
149What must be considered first when planning to carry out work in a confined space?
- ACan the work be done from the outside
- BHas sufficient manpower been allocated
- CHave the correct tools been arranged
- DHas the job been priced properly
150When working in a confined space, such as a sewer, what danger may occur?
- ANot enough time for the job to be done
- BBuild up of harmful gases
- CBoredom
- DGetting wet through
151To determine the safety of the atmosphere in an excavation, which of the following is essential
- AOnly entering for a short period to enable a quick escape
- BLooking for toxic gases
- CUsing a gas detector
- DSniffing the atmosphere after entry
152Before entering an excavation to start work, it must first be:
- Afilled with water then drained
- Binspected by the HSE
- Ccovered over and left overnight
- Dinspected by a competent person
153What is the purpose of using a ’permit to work’ system?
- ATo enable tools and equipment to be properly checked before the commencement of work
- BTo ensure that the client will pay for the work
- CTo help ensure a safe system of work
- DTo ensure the job is carried out by the quickest method
154You have to enter a manhole in which you know there are toxic gases. You have all the PPE but there does not appear to be a rescue plan in place. What should you do?
- AAsk your mate to stand-by at the top of the manhole with a length of rope
- BDo not enter the manhole until a rescue plan and rescue equipment are in place
- CPlan to carry out the job in short bursts
- DJust get on and do the job, it will probably be alright
155While digging a trench, you uncover a length of yellow marker tape at a depth of about 150mm. What does the presence of the marker tape mean?
- AThe area has a high water-table and precautions must be taken to prevent an in-rush of water
- BThere is a buried electrical cable and further excavation must be carried out with care
- CThere is contaminated soil below the level of the marker tape and all excavation must stop
- DThe excavation has reached a depth where the sides must now be supported
156When working alone:
- AMake sure someone responsible knows where you are
- BYou can do away with protective equipment
- CDon’t bother anyone if you have a problem, always sort it out yourself
- DWear headphones, it will make the day go more quickly
157If you are planning to work I a confined space, what is the first question that should be asked
- ACan the work be performed from the outside?
- BDoes the site require temporary lights
- CHow many workers are required for the job
- DWhat does the confined space contain
Informações
- Descrição
- Quiz sobre Bank of questions Health and Safety, criado por Vito Martino em 02-10-2014.
- Autor
- Vito Martino
- Idioma
- English
- Visualizações
- 450
- Etiquetas
- Avaliação
- Ainda sem avaliações Avalie este quiz