Quiz
31-60
Crie uma conta grátis para terminar este quiz
Salve seu progresso e veja sua nota final.
Já tem uma conta? Inicie sessão
Perguntas do quiz (30)
1Question 31: What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-tree topology?
- Apath cost
- Blowest port MAC address
- CVTP revision number
- Dhighest port priority number
- Eport priority number and MAC address
2Question 32: In a switched environment, what does the IEEE 802.1Q standard describe?
- Athe operation of VTP
- Ba method of VLAN trunking
- Can approach to wireless LAN communication
- Dthe process for root bridge selection
- EVLAN pruning
3Question 34: What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst Switch?
- AIt creates a VLAN 999 interface.
- BIt designates VLAN 999 for untagged traffic.
- CIt blocks VLAN 999 traffic from passing on the trunk.
- DIt designates VLAN 999 as the default for all unknown tagged traffic.
4Question 35: Which two protocols are used by bridges and/or switches to prevent loops in a layer 2 network? (Choose two.)
- A802.1d
- BVTP
- C802.1q
- DSTP
- ESAP
5Question 36: Which switch would STP choose to become the root bridge in the selection process?
- A32768: 11-22-33-44-55-66
- B32768: 22-33-44-55-66-77
- C32769: 11-22-33-44-55-65
- D32769: 22-33-44-55-66-78
6Question 37: A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?
- AMore collision domains will be created.
- BIP address utilization will be more efficient.
- CMore bandwidth will be required than was needed previously.
- DAn additional broadcast domain will be created.
7Question 38: What are three benefits of implementing VLANs? (Choose three.)
- AA higher level of network security can be reached by separating sensitive data traffic from other network traffic.
- BA more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure.
- CA more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure.
- DBroadcast storms can be mitigated by increasing the number of broadcast domains, thus reducing their size.
- EBroadcast storms can be mitigated by decreasing the number of broadcast domains, thus increasing their size.
- FVLANs make it easier for IT staff to configure new logical groups, because the VLANs all belong to the same broadcast domain.
- GPort-based VLANs increase switch-port use efficiency, thanks to 802.1Q trunks.
8Question 39: Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?
- A802.3ad
- B802.1w
- C802.1D
- D802.1Q
9Question 40: Which of the following are benefits of VLANs? (Choose three.)
- AThey increase the size of collision domains.
- BThey allow logical grouping of users by function.
- CThey can enhance network security.
- DThey increase the size of broadcast domains while decreasing the number of collision domains.
- EThey increase the number of broadcast domains while decreasing the size of the broadcast domains.
- FThey simplify switch administration.
10Question 42: Which two states are the port states when RSTP has converged? (Choose two.)
- Adiscarding
- Blistening
- Clearning
- Dforwarding
- Edisabled
11Question 43: Which two commands can be used to verify a trunk link configuration status on a given Cisco switch interface? (Choose two.)
- Ashow interface trunk
- Bshow interface interface
- Cshow ip interface brief
- Dshow interface vlan
- Eshow interface switchport
12Question 44: Which command enables RSTP on a switch?
- Aspanning-tree uplinkfast
- Bspanning-tree mode rapid-pvst
- Cspanning-tree backbonefast
- Dspanning-tree mode mst
13Question 48: Why will a switch never learn a broadcast address?
- ABroadcasts only use network layer addressing.
- BA broadcast frame is never forwarded by a switch.
- CA broadcast address will never be the source address of a frame.
- DBroadcast addresses use an incorrect format for the switching table.
- EBroadcast frames are never sent to switches.
14Question 50: Which two link protocols are used to carry multiple VLANs over a single link? (Choose two.)
- AVTP
- B802.1q
- CIGP
- DISL
- E802.3u
15Question 51: Assuming the default switch configuration, which VLAN range can be added, modified, and removed on a Cisco switch?
- A1-1001
- B2-1001
- C1-1002
- D2-1005
16Question 52: Which statement about VLAN operation on Cisco Catalyst switches is true?
- AWhen a packet is received from an 802.1Q trunk, the VLAN ID can be determined from the source MAC address and the MAC address table.
- BUnknown unicast frames are retransmitted only to the ports that belong to the same VLAN.
- CBroadcast and multicast frames are retransmitted to ports that are configured on different VLAN.
- DPorts between switches should be configured in access mode so that VLANs can span across the ports.
17Question 56: Which three statements about RSTP are true? (Choose three.)
- ARSTP significantly reduces topology reconverging time after a link failure.
- BRSTP expands the STP port roles by adding the alternate and backup roles.
- CRSTP port states are blocking, discarding, learning, or forwarding.
- DRSTP provides a faster transition to the forwarding state on point-to-point links than STP does.
- ERSTP also uses the STP proposal-agreement sequence.
- FRSTP uses the same timer-based process as STP on point-to-point links.
18Question 57: At which layer of the OSI model is RSTP used to prevent loops?
- Aphysical
- Bdata link
- Cnetwork
- Dtransport
19Question 58: What does a Layer 2 switch use to decide where to forward a received frame?
- Asource MAC address
- Bsource IP address
- Csource switch port
- Ddestination IP address
- Edestination port address
- Fdestination MAC address
20Question 60: Which two benefits are provided by creating VLANs? (Choose two.)
- Aadded security
- Bdedicated bandwidth
- Cprovides segmentation
- Dallows switches to route traffic between subinterfaces
- Econtains collisions
21Question 33: Refer to the exhibit. Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data?
https://drive.google.com/file/d/0B91K5x-kpk0yTjc1WFJqQnpueE0/edit- ASwitch-1 will drop the data because it does not have an entry for that MAC address.
- BSwitch-1 will flood the data out all of its ports except the port from which the data originated.
- CSwitch-1 will send an ARP request out all its ports except the port from which the data originated.
- DSwitch-1 will forward the data to its default gateway.
22Question 41: Refer to the exhibit. A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected to SwitchA. Which set of commands is required to accomplish this task?
https://drive.google.com/file/d/0B91K5x-kpk0yUHd2STY0aXY4U2s/edit- ASwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown - BSwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# ip default-gateway 192.168.8.254 255.255.255.0
SwitchB(config-if)# no shutdown - CSwitchB(config)# ip default-gateway 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown - DSwitchB(config)# ip default-network 192.168.8.254
SwitchB(config)# interface vlan 1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown - ESwitchB(config)# ip route 192.168.8.254 255.255.255.0
SwitchB(config)# interface FastEthernet 0/1
SwitchB(config-if)# ip address 192.168.8.252 255.255.255.0
SwitchB(config-if)# no shutdown
- ASwitchB(config)# interface FastEthernet 0/1
23Question 45: Refer to the exhibit. All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?
https://drive.google.com/file/d/0B91K5x-kpk0yWmVORExzTzJBYWs/edit- AThe access link needs to be configured in multiple VLANs.
- BThe link between the switches is configured in the wrong VLAN.
- CThe link between the switches needs to be configured as a trunk.
- DVTP is not configured to carry VLAN information between the switches.
- ESwitch IP addresses must be configured in order for traffic to be forwarded between the switches.
24Question 46: Refer to the exhibit. Which WAN protocol is being used?
https://drive.google.com/file/d/0B91K5x-kpk0yN012TVpFZU1Nek0/edit- AATM
- BHDLC
- CFrame Relay
- DPPP
25Question 47: Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the reason that interface FastEthernet 0/10 is not the root port for VLAN 2?
https://drive.google.com/file/d/0B91K5x-kpk0yWXJMYVltN1NaX2c/edit- AThis switch has more than one interface connected to the root network segment in VLAN 2.
- BThis switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree.
- CThis switch interface has a higher path cost to the root bridge than another in the topology.
- DThis switch has a lower bridge ID for VLAN 2 than the elected designated switch.
26Question 49: Refer to the exhibit. Why has this switch not been elected the root bridge for VLAN1?
https://drive.google.com/file/d/0B91K5x-kpk0yZV9JUHlQMjVkRmM/edit- AIt has more than one interface that is connected to the root network segment.
- BIt is running RSTP while the elected root bridge is running 802.1d spanning tree.
- CIt has a higher MAC address than the elected root bridge.
- DIt has a higher bridge ID than the elected root bridge.
27Question 53: Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? (Choose three.)
https://drive.google.com/file/d/0B91K5x-kpk0ySHR5Zk9rU1pQamc/edit- ASwitch A - Fa0/0
- BSwitch A - Fa0/1
- CSwitch B - Fa0/0
- DSwitch B - Fa0/1
- ESwitch C - Fa0/0
- FSwitch C - Fa0/1
28Question 54: Refer to the exhibit. How should the FastEthernet0/1 ports on the 2950 model switches that are shown in the exhibit be configured to allow connectivity between all devices?
https://drive.google.com/file/d/0B91K5x-kpk0yVm9IaWpWSmxQbEE/edit- AThe ports only need to be connected by a crossover cable.
- BSwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk - CSwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode access
SwitchX(config-if)# switchport access vlan 1 - DSwitchX(config)# interface fastethernet 0/1
SwitchX(config-if)# switchport mode trunk
SwitchX(config-if)# switchport trunk vlan 1
SwitchX(config-if)# switchport trunk vlan 10
SwitchX(config-if)# switchport trunk vlan 20
29Question 55: Refer to the exhibit. A frame on VLAN 1 on switch S1 is sent to switch S2 where the frame is received on VLAN 2. What causes this behavior?
https://drive.google.com/file/d/0B91K5x-kpk0yZGluaTdYMUotSHc/edit- Atrunk mode mismatches
- Ballowing only VLAN 2 on the destination
- Cnative VLAN mismatches
- DVLANs that do not correspond to a unique IP subnet
30Question 59: Refer to the exhibit. Which statement is true?
https://drive.google.com/file/d/0B91K5x-kpk0yU280dFZoSlVBb3c/edit- AThe Fa0/11 role confirms that SwitchA is the root bridge for VLAN 20.
- BVLAN 20 is running the Per VLAN Spanning Tree Protocol.
- CThe MAC address of the root bridge is 0017.596d.1580.
- DSwitchA is not the root bridge, because not all of the interface roles are designated.
Informações
- Descrição
- Quiz sobre 31-60, criado por Yael Legaria em 09-06-2015.
- Autor
- Yael Legaria
- Idioma
- English
- Visualizações
- 2
- Avaliação
- Ainda sem avaliações Avalie este quiz