DIKTA ICND 1 Ch 8

Descrição

Final / Review ICND 1 Quiz sobre DIKTA ICND 1 Ch 8, criado por Brian Gamble em 25-02-2016.
Brian Gamble
Quiz por Brian Gamble, atualizado more than 1 year ago
Brian Gamble
Criado por Brian Gamble mais de 8 anos atrás
30
0

Resumo de Recurso

Questão 1

Questão
Imagine that you have configured the enable secret command, followed by the enable password command, from the console. You log out of the switch and log back in at the console. Which command defines the password that you had to enter to access privileged mode?
Responda
  • enable password
  • enable secret
  • Neither
  • The password command, if it’s configured

Questão 2

Questão
An engineer had formerly configured a Cisco 2960 switch to allow Telnet access so that the switch expected a password of mypassword from the Telnet user. The engineer then changed the configuration to support Secure Shell. Which of the following commands could have been part of the new configuration? (Choose two answers.)
Responda
  • A username name password password vty mode sub command
  • A username name password password global configuration command
  • A login local vty mode sub command
  • A transport input ssh global configuration command

Questão 3

Questão
The following command was copied and pasted into configuration mode when a user was telnetted into a Cisco switch: banner login this is the login banner Which of the following is true about what occurs the next time a user logs in from the console?
Responda
  • No banner text is displayed.
  • The banner text “his is” is displayed.
  • The banner text “this is the login banner” is displayed.
  • The banner text “Login banner configured, no text defined” is displayed.

Questão 4

Questão
Which of the following is required when configuring port security with sticky learning?
Responda
  • Setting the maximum number of allowed MAC addresses on the interface with the switchport port-security maximum interface subcommand
  • Enabling port security with the switchport port-security interface subcommand
  • Defining the specific allowed MAC addresses using the switchport port-security mac-address interface subcommand
  • All the other answers list required commands

Questão 5

Questão
An engineer’s desktop PC connects to a switch at the main site. A router at the main site connects to each branch office through a serial link, with one small router and switch at each branch. Which of the following commands must be configured on the branch office switches, in the listed configuration mode, to allow the engineer to telnet to the branch office switches? (Choose three answers.)
Responda
  • The ip address command in interface configuration mode
  • The ip address command in global configuration mode
  • The ip default-gateway command in VLAN configuration mode
  • The ip default-gateway command in global configuration mode
  • The password command in console line configuration mode
  • The password command in vty line configuration mode

Questão 6

Questão
Which of the following describes a way to disable IEEE standard autonegotiation on a 10/100 port on a Cisco switch?
Responda
  • Configure the negotiate disable interface subcommand
  • Configure the no negotiate interface subcommand
  • Configure the speed 100 interface subcommand
  • Configure the duplex half interface subcommand
  • Configure the duplex full interface subcommand
  • Configure the speed 100 and duplex full interface subcommands

Questão 7

Questão
In which of the following modes of the CLI could you configure the duplex setting for interface Fast Ethernet 0/5?
Responda
  • User mode
  • Enable mode
  • Global configuration mode
  • VLAN mode
  • Interface configuration mode

Semelhante

DIKTA ICND1 Ch 7
Brian Gamble
DIKTA ICND1 Ch 4
Brian Gamble
DIKTA ICND 1 Ch 3
Brian Gamble
DIKTA ICND 1 Ch 10
Brian Gamble
DIKTA ICND 1 Ch 9
Brian Gamble
DIKTA ICND 1 Ch 13
Brian Gamble
DIKTA ICND1 Ch 1
Brian Gamble
DIKTA ICND1 Ch 2
Brian Gamble
Day 2 Quiz
Brian Gamble
Cisco CCENT R&S Exam Flashcards
Alexander Coffman
DIKTA ICND1 Ch 5
Brian Gamble