4689178
Description
Quiz by Brian Gamble, updated more than 1 year ago
|
Created by Brian Gamble
about 8 years ago
|
|
Question 1
Question
Imagine that a switch connects through an Ethernet cable to a router, and the router’s host name is Hannah. Which of the following commands could tell you information about the IOS version on Hannah without establishing a Telnet connection to Hannah? (Choose two answers.)
Answer
-
show neighbors Hannah
-
show cdp
-
show cdp neighbors
-
show cdp neighbors Hannah
-
show cdp entry Hannah
-
show cdp neighbors detail
Question 2
Question
A switch is cabled to a router whose host name is Hannah. Which of the following CDP commands could identify Hannah’s model of hardware? (Choose two answers.)
Answer
-
show neighbors
-
show neighbors Hannah
-
show cdp
-
show cdp interface
-
show cdp neighbors
-
show cdp entry Hannah
Question 3
Question
The output of the show interfaces status command on a 2960 switch shows interface Fa0/1 in a “disabled” state. Which of the following is true about interface Fa0/1? (Choose three answers.)
Answer
-
The interface is configured with the shutdown command.
-
The show interfaces fa0/1 command will list the interface with two status codes of administratively down and line protocol down.
-
The show interfaces fa0/1 command will list the interface with two status codes of up and down.
-
The interface cannot currently be used to forward frames.
-
The interface can currently be used to forward frames.
Question 4
Question
Switch SW1 uses its Gigabit 0/1 interface to connect to switch SW2’s Gigabit 0/2 interface. SW2’s Gi0/2 interface is configured with the speed 1000 and duplex full commands. SW1 uses all defaults for interface configuration commands on its Gi0/1
interface. Which of the following are true about the link after it comes up? (Choose
two answers.)
Answer
-
The link works at 1000 Mbps (1 Gbps).
-
SW1 attempts to run at 10 Mbps because SW2 has effectively disabled IEEE standard autonegotiation.
-
The link runs at 1 Gbps, but SW1 uses half-duplex and SW2 uses full-duplex.
-
Both switches use full-duplex.
Question 5
Question
The following line of output was taken from a show interfaces fa0/1 command:
Full-duplex, 100Mbps, media type is 10/100BaseTX
Which of the following are true about the interface? (Choose two answers.)
Answer
-
The speed was definitely configured with the speed 100 interface subcommand.
-
The speed might have been configured with the speed 100 interface subcommand.
-
The duplex was definitely configured with the duplex full interface subcommand.
-
The duplex might have been configured with the duplex full interface subcommand.The speed might have been configured with the speed 100 interface subcommand.
-
The duplex was definitely configured with the duplex full interface subcommand.
Question 6
Question
Which of the following commands list the MAC address table entries for MAC addresses configured by port security? (Choose two answers.)
Answer
-
show mac address-table dynamic
-
show mac address-table
-
show mac address-table static
-
show mac address-table port-security
Question 7
Question
On a Cisco Catalyst switch, you issue a show mac address-table command. Which of the following answers list information you would likely see in most lines of output? (Choose two answers.)
Answer
-
A MAC address
-
An IP address
-
A VLAN ID
-
Type (broadcast, multicast, or unicast)
Question 8
Question
Layer 2 switches SW1 and SW2 connect through a link, with port G0/1 on SW1 andport G0/2 on SW2. The network engineer wants to use 802.1Q trunking on this link.The show interfaces g0/1 switchport command on SW1 shows the output listedhere:
SW1# show interfaces gigabit0/1 switchport
Name: Gi0/1
Switchport: Enabled
Administrative Mode: trunk
Operational Mode: trunk
Which of the following must be true on switch SW2’s G0/2 port?
Answer
-
The operational state per the show interfaces switchport command must be“trunk.”
-
The administrative state per the show interfaces switchport command must be“trunk.”
-
SW2 must use the switchport mode trunk configuration command on G0/2, orthe link will not use trunking.
-
SW2 can use the switchport mode dynamic auto configuration command as one option to make the link use trunking.
Want to create your own Quizzes for free with GoConqr? Learn more.