Ajude a dar forma ao GoConqr. O que a gente deve adicionar?

Quiz

Ch. 6 Study Exam

Darion Ward 10 perguntas

Fazer o quiz

Perguntas do quiz (10)

  1. 1You wish to configure the speed and duplex settings for a port on your Catalyst 2960 switch. The interface is the fifth from the left. Which Global Configuration command will put you in the correct interface configuration mode to enter the new settings?
    1. Ainterface FastEthernet 5
    2. Binterface FastEthernet 0/5
    3. Cinterface FastEthernet 5/0
    4. Dinterface FastEthernet 1/5
  2. 2 An administrator wants to use the System Configuration dialog to set up the switch, and intends on assigning manual speed settings on each interface. After clearing NVRAM and restarting the system, a message asking, “Would you like to enter basic management setup [yes|no]?” appears. How should the administrator answer?
    1. AYes, because he wishes to use setup to configure the device.
    2. BYes, because basic management setup allows interface configuration settings.
    3. CNo, because the message is referring to the management interface and not a setup mode.
    4. DNo, because basic management mode does not allow for interface configuration.
  3. 3Examining the output of a show running-config command, you notice this command:
    banner login welcome to Switch12. Please prepare to login
    What message will display when the switch is accessed from the console?
    1. Awelcome to Switch12. Please prepare to login
    2. Bwelcome to Switch12
    3. Cwelcome to Sw
    4. DNone of the above
  4. 4A user wishes to stop syslog messages from interrupting the command prompt display during a console session. Which command accomplishes this?
    1. ASwitch(config)# logging synchronous
    2. BSwitch(config-if)# logging synchronous
    3. CSwitch(config-line)# logging synchronous
    4. DNone of the above
  5. 5You examine the output of a show running-config command and notice two commands: enable password Cisco and enable secret CCENT. Later on, you establish a console connection to the switch and are prompted for a password to enter Privileged mode. Which password should you use?
    1. ACisco
    2. BCCENT
    3. CBoth. The enable password is first, followed by the enable secret.
    4. DBoth. The enable secret is first, followed by the enable password.
    5. ENeither. Access to a console connection already grants Privileged mode access.
  6. 6After entering the command service password-encryption, you notice all passwords appear in encrypted format within the configuration. You then issue a no service password-encryption command and save the configuration. The next day, a peer changes the password on the console line, using the command password Cisco. After executing a show running-config, which of the following would be true?
    1. AAll passwords, except for the enable secret, will display in clear text.
    2. BAll passwords, including the enable secret, will display in clear text.
    3. CAll passwords will continue to display in encrypted format.
    4. DThe console password will display in clear text; all others will display encrypted.
  7. 7You wish to force users to use two-factor authentication on the console before gaining a command prompt. Which of the following commands are required?
    1. ASwitch(config)# username Bob password Cisco
    2. BSwitch(config-line)# username Bob password Cisco
    3. CSwitch(config)# login
    4. DSwitch(config-line)# login
    5. ESwitch(config)# login local
    6. FSwitch(config-line)# login local
  8. 8An administrator wishes to force remote access users to connect using SSH. Which command must be entered to disable Telnet access and force SSH use?
    1. AThe no telnet Global Configuration command
    2. Bno telnet in vty Line Configuration mode
    3. CThe transport input ssh Global Configuration command
    4. Dtransport input ssh in vty Line Configuration mode
  9. 9An administrator wishes to add a static management IP address to the switch. Which of the following commands is/are required?
    1. AThe ip address ip_address subnet_mask Global Configuration command
    2. Bip address ip_address subnet_mask on interface Vlan1 configuration mode
    3. CThe ip default-gateway ip_address Global Configuration command
    4. Dip default-gateway ip_address on interface Vlan1 configuration mode
  10. 10 A segment of the output from a show interfaces status command is displayed next:

    *look at textbook image*

    Which of the following are true regarding the interfaces?
    1. AAutonegotiation has been disabled for interface 5.
    2. BAutonegotiation has been disabled for interface 6.
    3. CThe speed 100 and duplex auto commands have been configured for interface 5.
    4. DThe speed 100 and duplex full commands have been configured for interface 5.

Informações

Descrição
CCENT Information System Quiz sobre Ch. 6 Study Exam , criado por Darion Ward em 08-05-2017.
Idioma
English
Visualizações
2
Etiquetas
information systemccent
Avaliação
Ainda sem avaliações
Avalie este quiz
Avalie este quiz

Mais sobre Switch Configuration and Administration

Fale Conosco

Sobre o que é sua mensagem?

O que a gente deve adicionar?