Quiz
Pepinillo 2
This quiz has a time limit, so it opens in the usual player.
Questions in this quiz (200)
1Refer to the exhibit. Which two commands when used together create port channel 10? (Choose two.)

- Aint range g0/0-1 channel-group 10 mode active
- Bint range g0/0-1 channel-group 10 mode desirable
- Cint range g0/0-1 channel-group 10 mode passive
- Dint range g0/0-1 channel-group 10 mode auto
- Eint range g0/0-1 channel-group 10 mode on
2Refer to the exhibit. An administrator is tasked with configuring a voice VLAN. What is the expected outcome when a Cisco phone is connected to the GigabitEthernet 3/1/4 port on a switch?

- AThe phone and a workstation that is connected to the phone do not have VLAN connectivity.
- BThe phone sends and receives data in VLAN 50, but a workstation connected to the phone sends and receives data in VLAN 1.
- CThe phone sends and receives data in VLAN 50, but a workstation connected to the phone has no VLAN connectivity.
- DThe phone and a workstation that is connected to the phone send and receive data in VLAN50.
3Refer to the exhibit. Which action is expected from SW1 when the untagged frame is received on theGigabitEthernet0/1 interface?

- AThe frame is processed in VLAN 1
- BThe frame is processed in VLAN 11
- CThe frame is processed in VLAN 5
- DThe frame is dropped
4Which command is used to enable LLDP globally on a Cisco IOS ISR?
- Alldp run
- Blldp enable
- Clldp transmit
- Dcdp run
- Ecdp enable
5Which command should you enter to configure an LLDP delay time of 5 seconds?
- Alldp timer 5000
- Blldp holdtime 5
- Clldp reinit 5000
- Dlldp reinit 5
6In a CDP environment, what happens when the CDP interface on an adjacent device is configured without an IP address?
- ACDP becomes inoperable on that neighbor
- BCDP uses the IP address of another interface for that neighbor
- CCDP operates normally, but it cannot provide IP address information for that neighbor
- DCDP operates normally, but it cannot provide any information for that neighbor
7DRAG DROP -
Drag and drop the benefits of a Cisco Wireless Lan Controller from the left onto the correct examples on the right. Select and Place:
- AEasy Deployment Process
Dynamic RF Feature
Easy upgrade process
Optimized user performance - BDynamic RF Feature
Optimized user performance
Easy Deployment Process
Easy upgrade process - CEasy upgrade process
Optimized user performance
Easy Deployment Process
Dynamic RF Feature
- AEasy Deployment Process
8When configuring an EtherChannel bundle, which mode enables LACP only if a LACP device is detected?
- APassive
- BDesirable
- COn
- DAuto
- EActive
9Refer to the exhibit. Which VLAN ID is associated with the default VLAN in the given environment?

- AVLAN 1
- BVLAN 5
- CVLAN 10
- DVLAN 20
10Which two VLAN IDs indicate a default VLAN? (Choose two.)
- A0
- B1
- C1005
- D1006
- E4096
11Which two pieces of information about a Cisco device can Cisco Discovery Protocol communicate? (Choose two.)
- Athe native VLAN
- Bthe trunking protocol
- Cthe VTP domain
- Dthe spanning-tree priority
- Ethe spanning-tree protocol
12After you deploy a new WLAN controller on your network, which two additional tasks should you consider?
- Adeploy load balancers
- Bconfigure additional vlans
- Cconfigure multiple VRRP groups
- Ddeploy POE switches
- Econfigure additional security policies
13Refer to the exhibit. How will switch SW2 handle traffic from VLAN 10 on SW1?

- AIt sends the traffic to VLAN 10.
- BIt sends the traffic to VLAN 100.
- CIt drops the traffic.
- DIt sends the traffic to VLAN 1.
14Which two commands can you use to configure an actively negotiate EtherChannel? (Choose two.)
- Achannel-group 10 mode on
- Bchannel-group 10 mode auto
- Cchannel-group 10 mode passive
- Dchannel-group 10 mode desirable
- Echannel-group 10 mode active
15How does STP prevent forwarding loops at OSI Layer 2?
- ATTL
- BMAC address forwarding
- CCollision avoidance
- DPort blocking
16Which two statements about VTP are true? (Choose two.)
- AAll switches must be configured with the same VTP domain name
- BAll switches must be configured to perform trunk negotiation
- CAll switches must be configured with a unique VTP domain name
- DThe VTP server must have the highest revision number in the domain
- EAll switches must use the same VTP version
17Which type does a port become when it receives the best BPDU on a bridge?
- AThe designated port
- BThe backup port
- CThe alternate port
- DThe root port
18Which value can you modify to configure a specific interface as the preferred forwarding interface?
- AThe interface number
- BThe port priority
- CThe VLAN priority
- DThe hello time
19Which statement about Cisco Discovery Protocol is true?
- AIt is a Cisco-proprietary protocol.
- BIt runs on the network layer.
- CIt can discover information from routers, firewalls, and switches.
- DIt runs on the physical layer and the data link layer.
20What are two reasons a network administrator would use CDP? (Choose two.)
- Ato verify the type of cable interconnecting two devices
- Bto determine the status of network services on a remote device
- Cto obtain VLAN information from directly connected switches
- Dto verify Layer 2 connectivity between two devices when Layer 3 fails
- Eto obtain the IP address of a connected device in order to telnet to the device
- Fto determine the status of the routing protocols between directly connected routers
21What are two benefits of using VTP in a switching environment? (Choose two.)
- AIt allows switches to read frame tags.
- BIt allows ports to be assigned to VLANs automatically.
- CIt maintains VLAN consistency across a switched network.
- DIt allows frames from multiple VLANs to use a single interface.
- EIt allows VLAN information to be automatically propagated throughout the switching environment.
22Which three statements are typical characteristics of VLAN arrangements? (Choose three.)
- AA new switch has no VLANs configured.
- BConnectivity between VLANs requires a Layer 3 device.
- CVLANs typically decrease the number of collision domains.
- DEach VLAN uses a separate address space.
- EA switch maintains a separate bridging table for each VLAN.
- FVLANs cannot span multiple switches.
23On a corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?
- Aa router with subinterfaces configured on the physical interface that is connected to the switch
- Ba router with an IP address on the physical interface connected to the switch
- Ca switch with an access link that is configured between the switches
- Da switch with a trunk link that is configured between the switches
24Which statement about LLDP is true?
- AIt is a Cisco proprietary protocol.
- BIt is configured in global configuration mode.
- CThe LLDP update frequency is a fixed value.
- DIt runs over the transport layer.
25What is a function of Wireless LAN Controller?
- Aregister with a single access point that controls traffic between wired and wireless endpoints
- Buse SSIDs to distinguish between wireless clients
- Csend LWAPP packets to access points
- Dmonitor activity on wireless and wired LANs
26Which technology is used to improve web traffic performance by proxy caching?
- AWSA
- BFirepower
- CASA
- DFireSIGHT
27What criteria is used first during the root port selection process?
- Alocal port ID
- Blowest path cost to the toot bridge
- Clowest neighbor's bridge ID
- Dlowest neighbor's port ID
28Which statement about VLAN configuration is true?
- AThe switch must be in VTP server or transparent mode before you can configure a VLAN
- BThe switch must be in config-vlan mode before you configure an extended VLAN
- CDynamic inter-VLAN routing is supported on VLAN2 through VLAN 4064
- DA switch in VTP transparent mode save the VLAN databases to the running configuration only
29Refer to the exhibit. What two conclusions should be made about this configuration? (Choose two.)

- AThe root port is FastEthernet 2/1
- BThe designated port is FastEthernet 2/1
- CThe spanning-tree mode is PVST+
- DThis is a root bridge
- EThe spanning-tree mode is Rapid PVST+
30A network engineer must create a diagram of a multivendor network. Which command must be configured on the Cisco devices so that the topology of the network is allowed to be mapped?
- ADevice(config)#lldp run
- BDevice(config)#cdp run
- CDevice(config-if)#cdp enable
- DDevice(config)#flow-sampler-map topology
31How do AAA operations compare regarding user identification, user services, and access control?
- AAuthorization provides access control, and authentication tracks user services
- BAuthentication identifies users, and accounting tracks user services
- CAccounting tracks user services, and authentication provides access control
- DAuthorization identifies users, and authentication provides access control
32What is the difference between RADIUS and TACACS+?
- ARADIUS logs all commands that are entered by the administrator, but TACACS+ logs only start, stop, and interim commands.
- BTACACS+ separates authentication and authorization, and RADIUS merges them.
- CTACACS+ encrypts only password information, and RADIUS encrypts the entire payload.
- DRADIUS is most appropriate for dial authentication, but TACACS+ can be used for multiple types of authentication.
33What is a difference between local AP mode and FlexConnect AP mode?
- ALocal AP mode creates two CAPWAP tunnels per AP to the WLC
- BLocal AP mode causes the AP to behave as if it were an autonomous AP
- CFlexConnect AP mode fails to function if the AP loses connectivity with the WLC
- DFlexConnect AP mode bridges the traffic from the AP to the WLC when local switching isconfigured
34The SW1 interface g0/1 is in the down/down state. What are two reasons for the interface condition? (Choose two.)
- AThere is a protocol mismatch
- BThere is a duplex mismatch
- CThe interface is shut down
- DThe interface is error-disabled
- EThere is a speed mismatch
35How will Link Aggregation be implemented on a Cisco Wireless LAN Controller?
- AThe EtherChannel must be configured in ג€mode active
- BWhen enabled, the WLC bandwidth drops to 500 Mbps.
- CTo pass client traffic, two or more ports must be configured.
- DOne functional physical port is needed to pass client traffic.
36Which two conditions must be met before SSH operates normally on a Cisco IOS switch? (Choose two.)
- AIP routing must be enabled on the switch.
- BA console password must be configured on the switch.
- CTelnet must be disabled on the switch.
- DThe switch must be running a k9 (crypto) IOS image.
- EThe ip domain-name command must be configured on the switch.
37Refer to the exhibit. Which password must an engineer use to enter the enable mode?

- Aadminadmin123
- Bcisco123
- Cdefault
- Dtesting1234
38Which state does the switch port move to when PortFast is enabled?
- Ablocking
- Blistening
- Clearning
- Dforwarding
39Which protocol prompts the Wireless LAN Controller to generate its own local web administration SSL certificate for GUI access?
- ARADIUS
- BHTTPS
- CTACACS+
- DHTTP
40An engineer must configure interswitch VLAN communication between a Cisco switch and a third-party switch. Which action should be taken?
- Aconfigure DSCP
- Bconfigure IEEE 802.1q
- Cconfigure ISL
- Dconfigure IEEE 802.1p
41An engineer requires a switch interface to actively attempt to establish a trunk link with a neighbor switch. What command must be configured?
- Aswitchport mode trunk
- Bswitchport mode dynamic desirable
- Cswitchport nonegotiate
- Dswitchport mode dynamic auto
42Refer to the exhibit. After the election process, what is the root bridge in the HQ LAN?
Switch 1:
0C:E0:38:81:32:58
-
Switch 2:
0C:0E:15:22:1A:61
-
Switch 3:
0C:0E:15:1D:3C:9A
-
Switch 4:
0C:E0:19:A1:4D:16
-
- ASwitch 1
- BSwitch 2
- CSwitch 3
- DSwitch 4
43An engineer must establish a trunk link between two switches. The neighboring switch is set to trunk or desirable mode. What action should be taken?
- Aconfigure switchport nonegotiate
- Bconfigure switchport mode dynamic desirable
- Cconfigure switchport mode dynamic auto
- Dconfigure switchport trunk dynamic desirable
44Which spanning-tree enhancement avoids the learning and listening states and immediately places ports in the forwarding state?
- ABPDUfilter
- BPortFast
- CBackbonefast
- DBPDUguard
45How does the dynamically-learned MAC address feature function?
- AThe CAM table is empty until ingress traffic arrives at each port
- BSwitches dynamically learn MAC addresses of each connecting CAM table.
- CThe ports are restricted and learn up to a maximum of 10 dynamically-learned addresses
- DIt requires a minimum number of secure MAC addresses to be filled dynamically
46When using Rapid PVST+, which command guarantees the switch is always the root bridge for VLAN200?
- Aspanning-tree vlan 200 priority 614440
- Bspanning-tree vlan 200 priority 0
- Cspanning-tree vlan 200 root primary
- Dspanning-tree vlan 200 priority 38813258
47Refer to the exhibit. Which command must be executed for Gi1/1 on SW1 to passively become a trunk port if Gi1/1 on SW2 is configured in desirable or trunk mode?

- Aswitchport mode dynamic auto
- Bswitchport mode dot1-tunnel
- Cswitchport mode dynamic desirable
- Dswitchport mode trunk
48Refer to the exhibit. The entire contents or the MAC address table are shown. Sales-4 sends a data frame to Sales-1. What does the switch do as it receives the frame from Sales-4?

- AMap the Layer 2 MAC address to the Layer 3 IP address and forward the frame.
- BInsert the source MAC address and port into the forwarding table and forward the frame to Sales-1.
- CPerform a lookup in the MAC address table and discard the frame due to a missing entry.
- DFlood the frame out of all ports except on the port where Sales-1 is connected.
49Refer to the exhibit. An engineer must configure GigabitEthernet1/1 to accommodate voice and data traffic. Which configuration accomplishes this task?

- Ainterface gigabitethernet1/1 switchport mode access switchport access vlan 300 switchport voice vlan 400
- Binterface gigabitethernet1/1 switchport mode trunk switchport trunk vlan 300 switchport trunk vlan 400
- Cinterface gigabitethernet1/1 switchport mode access switchport voice vlan 300 switchport access vlan 400
- Dinterface gigabitethernet1/1 switchport mode trunk switchport trunk vlan 300 switchport voice vlan 400
50An engineer needs to add an old switch back into a network. To prevent the switch from corrupting the VLAN database, with action must be taken?
- AAdd the switch in the VTP domain with a lower revision number.
- BAdd the switch in the VTP domain with a higher revision number.
- CAdd the switch with DTP set to dynamic desirable.
- DAdd the switch with DTP set to desirable.
51Which technology prevents client devices from arbitrarily connecting to the network without state remediation?
- A802.11n
- B802.1x
- CMAC Authentication Bypass
- DIP Source Guard
52Which protocol does an access point use to draw power from a connected switch?
- AInternet Group Management Protocol
- BCisco Discovery Protocol
- CAdaptive Wireless Path Protocol
- DNeighbor Discovery Protocol
53An administrator must secure the WLC from receiving spoofed association requests. Which steps must be taken to configure the WLC to restrict the requests and force the user to wait 10 ms to retry an association request?
- AEnable MAC filtering and set the SA Query timeout to 10.
- BEnable 802.1x Layer 2 security and set the Comeback timer to 10.
- CEnable Security Association Teardown Protection and set the SA Query timeout to 10.
- DEnable the Protected Management Frame service and set the Comeback timer to 10.
54Refer to the exhibit. Only four switches are participating in the VLAN spanning-tree process.
Branch-1: priority 614440 -
Branch-2: priority 39391170 -
Branch-3: priority 0 -
Branch-4: root primary -
Which switch becomes the permanent root bridge for VLAN 5?
- ABranch-1
- BBranch-2
- CBranch-3
- DBranch-4
55An engineer must configure traffic for a VLAN that is untagged by the switch as it crosses a trunk link. Which command should be used?
- Aswitchport trunk encapsulation dot1q
- Bswitchport trunk allowed vlan 10
- Cswitchport mode trunk
- Dswitchport trunk native vlan 10
56What are two benefits of using the PortFast feature? (Choose two.)
- AEnabled interfaces are automatically placed in listening state.
- BEnabled interfaces wait 50 seconds before they move to the forwarding state.
- CEnabled interfaces never generate topology change notifications.
- DEnabled interfaces come up and move to the forwarding state immediately.
- EEnabled interfaces that move to the learning state generate switch topology change notifications.
57What is the benefit of configuring PortFast on an interface?
- AThe frames entering the interface are marked with the higher priority and then processed faster by a switch.
- BAfter the cable is connected, the interface is available faster to send and receive user data.
- CReal-time voice and video frames entering the interface are processed faster.
- DAfter the cable is connected, the interface uses the fastest speed setting available for that cable type.
58DRAG DROP -
Drag and drop the functions of AAA supporting protocols from the left onto the protocols on the right.
Select and Place:
- ARADIUS
Encrypts only the password when it sends an access request.
Uses UDP.
Combines authentication and authorization.
TACACS+
Encrypts the entire body of the access-request packet.
Separates all three AAA operations.
Uses TCP. - BRADIUS
Encrypts only the password when it sends an access request.
Separates all three AAA operations.
Uses TCP.
TACACS+
Encrypts the entire body of the access-request packet.
Uses UDP.
Combines authentication and authorization. - CRADIUS
Encrypts the entire body of the access-request packet.
Separates all three AAA operations.
Uses TCP.
TACACS+
Encrypts only the password when it sends an access request.
Uses UDP.
Combines authentication and authorization.
- ARADIUS
59Why does a switch flood a frame to all ports?
- AThe frame has zero destination MAC addresses.
- BThe destination MAC address of the frame is unknown.
- CThe source MAC address of the frame is unknown
- DThe source and destination MAC addresses of the frame are the same.
60An engineer configures interface Gi1/0 on the company PE router to connect to an ISP. Neighbor discovery is disabled. Which action is necessary to complete the configuration if the ISP uses third-party network devices?

- ADisable autonegotiation.
- BEnable LLDP globally.
- CEnable LLDP-MED on the ISP device.
- DDisable Cisco Discovery Protocol on the interface.
61DRAG DROP -
Drag and drop the Rapid PVST+ forwarding state actions from the left to the right. Not all actions are used.
Select and Place:
- ABPDUs received are forwarded to the system module.
BPDUs received from the system module are processed and transmitted.
Frames received from the attached segment are discarded.
The port in the forwarding state responds to network management messages. - BThe port in the forwarding state responds to network management messages.
BPDUs received from the system module are processed and transmitted.
Frames received from the attached segment are discarded.
BPDUs received are forwarded to the system module. - CThe port in the forwarding state responds to network management messages.
Frames received from the attached segment are discarded.
BPDUs received from the system module are processed and transmitted.
BPDUs received are forwarded to the system module
- ABPDUs received are forwarded to the system module.
62Which access point mode relies on a centralized controller for management, roaming, and SSID configuration?
- Alightweight mode
- Bautonomous mode
- Cbridge mode
- Drepeater mode
63Refer to the exhibit. A network engineer must configure communication between PC A and the File Server. To prevent interruption for any other communications, which command must be configured?

- Aswitchport truck allowed vlan 12
- Bswitchport truck allowed vlan none
- Cswitchport truck allowed vlan add 13
- Dswitchport truck allowed vlan remove 10-11
64Refer to the exhibit. What is the result if Gig1/11 receives an STP BPDU?

- AThe port transitions to STP blocking.
- BThe port immediately transitions to STP forwarding.
- CThe port goes into error-disable state.
- DThe port transitions to the root port.
65Which access layer threat-mitigation technique provides security based on identity?
- ADynamic ARP Inspection
- BDHCP snooping
- C802.1x
- Dusing a non-default native VLAN
66Refer to the exhibit. Which action do the switches take on the trunk link?

- AThe trunk does not form, and the ports go into an err-disabled status.
- BThe trunk forms, but the mismatched native VLANs are merged into a single broadcast domain.
- CThe trunk forms, but VLAN 99 and VLAN 999 are in a shutdown state.
- DThe trunk does not form, but VLAN 99 and VLAN 999 are allowed to traverse the link.
67A network engineer must configure two new subnets using the address block 10.70.128.0/19 to meet these requirements:
The first subnet must support 24 hosts.
The second subnet must support 472 hosts.
Both subnets must use the longest subnet mask possible from the address block.
Which two configurations must be used to configure the new subnets and meet a requirement to use the first available address in each subnet for the router interfaces? (Choose two.)- Ainterface vlan 1148 ip address 10.70.148.1 255.255.254.0
- Binterface vlan 3002 ip address 10.70.147.17 255.255.255.224
- Cinterface vlan 4722 ip address 10.70.133.17 255.255.255.192
- Dinterface vlan 1234 ip address 10.70.159.1 255.255.254.0
- Einterface vlan 155 ip address 10.70.155.65 255.255.255.224
68Refer to the exhibit. An administrator must configure interfaces Gi1/1 and Gi1/3 on switch SW11. PC-1and PC-2 must be placed in the Data VLAN, and Phone-1 must be placed in the Voice VLAN. Which configuration meets these requirements?

- Ainterface gigabitethernet1/1 switchport mode access switchport access vlan 8 !interface gigabitethernet1/3 switchport mode access switchport access vlan 8switchport voice vlan 9
- Binterface gigabitethernet1/1 switchport mode access switchport access vlan 8 ! interfacegigabitethernet1/3 switchport mode trunk switchport trunk vlan 8 switchport voice vlan 9
- Cinterface gigabitethernet1/1 switchport mode access switchport access vlan 9 ! interfacegigabitethernet1/3 switchport mode trunk switchport trunk vlan 8 switchport trunk vlan 9
- Dinterface gigabitethernet1/1 switchport mode access switchport access vlan 8 ! interfacegigabitethernet1/3 switchport mode access switchport voice vlan 8 switchport access vlan 9
69Refer to the exhibit. Users need to connect to the wireless network with IEEE 802.11r-compatibledevices. The connection must be maintained as users travel between floors or to other areas in the building. What must be the configuration of the connection?

- ADisable AES encryption.
- BEnable Fast Transition and select the FT 802.1x option.
- CEnable Fast Transition and select the FT PSK option.
- DSelect the WPA Policy option with the CCKM option.
70Refer to the exhibit. An engineer is asked to insert the new VLAN into the existing trunk without modifying anything previously configured. Which command accomplishes this task?

- Aswitchport trunk allowed vlan 100-104
- Bswitchport trunk allowed vlan 104
- Cswitchport trunk allowed vlan all
- Dswitchport trunk allowed vlan add 104
71Aside from discarding, which two states does the switch port transition through while using RSTP(802.1w)? (Choose two.)
- Ablocking
- Bspeaking
- Clistening
- Dlearning
- Eforwarding
72DRAG DROP -
Drag and drop the facts about wireless architectures from the left onto the types of access point on the right. Not all options are used.
Select and Place:
- AAutonomous Access Point
Accessible for management via Telnet, SSH, or a web GUI.
Configured and managed by a WLC.
Cloud-Based Access Point
Managed from a web-based dashboard.
Supports automatic deployment. - BAutonomous Access Point
Accessible for management via Telnet, SSH, or a web GUI.
Supports automatic deployment.
Cloud-Based Access Point
Managed from a web-based dashboard.
Configured and managed by a WLC. - CAutonomous Access Point
Accessible for management via Telnet, SSH, or a web GUI.
Configured and managed by a WLC.
Cloud-Based Access Point
Managed from a web-based dashboard.
Supports automatic deployment.
- AAutonomous Access Point
73Which interface mode must be configured to connect the lightweight APs in a centralized architecture?
- AWLAN dynamic
- Btrunk
- Caccess
- Dmanagement
74Refer to the exhibit. The following must be considered:
*SW1 is fully configured for all traffic.
*The SW4 and SW9 links to SW1 have been configured.
*The SW4 interface Gi0/1 and Gi0/0 on SW9 have been configured.
*The remaining switches have had all VLANs added to their VLAN database.
Which configuration establishes a successful ping from PC2 to PC7 without interruption to traffic flow between other PCs?
- ASW4 interface Gi0/7 switchport mode trunk switchport trunk allowed vlan 108 ! interface Gi/0/2 switchport mode access switchport access vlan 14 SW11# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14,108 ! interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14,108 SW9# interface Gi0/2 switchport mode access switchport access vlan 14
- BSW4 interface Gi0/2 switchport mode trunk switchport trunk allowed vlan14,108 SW11# interface Gi0/2 switchport mode trunk switchport trunk allowed
vlan 14,108 !! interface Gi0/1 switchport mode trunk switchport trunk allowed vlan 14,108 SW9# interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14 - CSW4 interface Gi0/2 switchport mode trunk switchport trunk allowed vlan 14 SW11# interfaceGi0/1 switchport mode trunk switchport trunk allowed vlan 14 SW9# interface Gi0/2switchport mode trunk switchport trunk allowed vlan 108
- DSW4 interface Gi/0/2 switchport mode access switchport access vlan 14 SW11# interfaceGi0/2 switchport mode trunk switchport trunk allowed vlan 14 ! interface Gi0/0 switchport mode access switchport access vlan 14 ! interface Gi0/1 switchport mode trunk SW9#interface Gi0/2 switchport mode access switchport access vlan 14
75Refer to the exhibit. The network administrator must prevent the switch
Cat9K-2 IP address from being visible in LLDP without disabling the protocol. Which action must be taken to complete the task?
- AConfigure the no lldp mac-phy-cfg command globally on Cat9K-2.
- BConfigure the no lldp receive command on interface G1/0/21 on Cat9K-1.
- CConfigure the no lldp transmit command on interface G1/0/21 on Cat9K-1.
- DConfigure the no lldp tlv-select management-address command globally onCat9K-2.
76Refer to the exhibit. An engineer has started to configure replacement switch SW1. To verify part of the configuration, the engineer issued the commands as shown and noticed that the entry for PC2 is missing. Which change must be applied to SW1 so that PC1 and PC2 communicate normally?

- ASW1(config)#interface fa0/2 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#noswitchport trunk allowed vlan 3 SW1(config-if)#switchport trunk allowed vlan 2
- BSW1(config)#interface fa0/2 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#switchport trunk native vlan 2 SW1(config-if)#switchport trunk allowed vlan 3
- CSW1(config)#interface fa0/2 SW1(config-if)#no switchport mode trunkSW1(config-if)#no switchport trunk allowed vlan 3 SW1(config-if)#switchport mode access
- DSW1(config)#interface fa0/1 SW1(config-if)#no switchport access vlan 2 SW1(config-if)#switchport access vlan 3 SW1(config-if)#switchport trunk allowed vlan 2
77Refer to the exhibit. Which switch becomes the root of the spanning tree?
Switch 1 -
BID: 32778 0018.184e.3c00 -
Switch 2 -
BID: 24586 001a.e3ff.a680 -
Switch 3 -
BID: 28682 0022.55cf.cc00 -
Switch 4 -
BID: 64000 4e15.8403.08f -
- ASwitch 1
- BSwitch 2
- CSwitch 3
- DSwitch 4
78DRAG DROP -
Drag and drop the facts about wireless architectures from the left onto the types of access point on the right. Not all options are used.
Select and Place:
- AAutonomous Access Point
Requires a management IP address.
Accessible for management via Telnet, SSH, or a Web GUI.
Lightweight Access Point
Configured and managed by a WLC.
Supports automatic deployment. - BAutonomous Access Point
Configured and managed by a WLC.
Accessible for management via Telnet, SSH, or a Web GUI.
Lightweight Access Point
Requires a management IP address.
Supports automatic deployment. - CAutonomous Access Point
Configured and managed by a WLC.
Supports automatic deployment.
Lightweight Access Point
Requires a management IP address.
Accessible for management via Telnet, SSH, or a Web GUI.
- AAutonomous Access Point
79Refer to the exhibit. An engineer is configuring a Layer 3 port-channel interface with LACP. The configuration on the first device is complete, and it is verified that both interfaces have registered the neighbor device in the CDP table. Which task on the neighbor device enables the new port channel to come up without negotiating the channel?

- AConfigure the IP address of the neighboring device.
- BBring up the neighboring interfaces using the no shutdown command.
- CChange the EtherChannel mode on the neighboring interfaces to auto.
- DModify the static EtherChannel configuration of the device to passive mode.
80Refer to the exhibit. Which configuration establishes a Layer 2 LACP EtherChannel when applied to both switches?

- AInterface range G1/1 1/3 "€ ג switchport mode trunk channel-group 1 mode
active no shutdown - BInterface range G1/1 1/3 "€ ג switchport mode access channel-group 1 mode passive no shutdown
- CInterface range G1/1 1/3 "€ ג switchport mode trunk channel-group 1 mode desirable no shutdown
- DInterface range G1/1 1/3 "€ ג switchport mode access channel-group 1 mode on no shutdown
- AInterface range G1/1 1/3 "€ ג switchport mode trunk channel-group 1 mode
81Which switching concept is used to create separate broadcast domains?
- ASTP
- BVTP
- CVLAN
- DCSMA/CD
82Refer to the exhibit. Which action must be taken so that neighboring devices rapidly discover switchCat9300?

- AEnable portfast on the ports that connect to neighboring devices.
- BConfigure the cdp timer 10 command on switch Cat9300.
- CConfigure the cdp holdtime 10 command on switch Cat9300
- DConfigure the cdp timer 10 command on the neighbors of switch Cat9300
83What is a requirement when configuring or removing LAG on a WLC?
- AThe incoming and outgoing ports for traffic flow must be specified if LAG is enabled.
- BThe management interface must be reassigned if LAG is disabled
- CThe controller must be rebooted after enabling or reconfiguring LAG
- DMultiple untagged interfaces on the same port must be supported
84DRAG DROP -
Drag and drop the threat-mitigation techniques from the left onto the types of threat or attack they mitigate on the right.
Select and Place:
- AConfigure a VLAN access control list.
Configure the dynamic ARP inspection feature.
Configure the root guard feature.
Configure the BPDU guard feature. - BConfigure the root guard feature.
Configure the dynamic ARP inspection feature.
Configure a VLAN access control list.
Configure the BPDU guard feature. - CConfigure the root guard feature.
Configure the BPDU guard feature.
Configure a VLAN access control list.
Configure the dynamic ARP inspection feature.
- AConfigure a VLAN access control list.
85Which type of port is used to connect the wired network when an autonomous AP maps two VLANs to its WLANs?
- Aaccess
- BLAG
- Ctrunk
- DEtherChannel
86A network administrator needs to aggregate 4 ports into a single logical link which must negotiate layer2 connectivity to ports on another switch. What must be configured when using active mode on both sides of the connection?
- ALLDP
- BLACP
- CCisco vPC
- D802.1q trunks
87Refer to the exhibit. An engineer built a new L2 LACP EtherChannel between SW1 and SW2 and executed these show commands to verify the work establish an LACP port channel?

- AChange the channel-group mode on SW1 to desirable
- BChange the channel-group mode on SW1 to active or passive
- CChange the channel-group mode on SW2 to auto
- DConfigure the interface port-channel 1 command on both swtiches
88Refer to the exhibit. For security reasons, automatic neighbor discovery must be disabled on the R5Gi0/1 interface. These tasks must be completed:
*Disable all neighbor discovery methods on R5 interface Gi0/1
*Permit neighbor discovery on R5 interface Gi0/2.
*Verify there are no dynamically learned neighbors on R5 interface Gi0/1.
*Display the IP address of R6's interface Gi0/2
Which configuration must be used?
- AR5(config)#int Gi0/1 R5(config-if)#no cdp enable R5(config-if)#exit R5(config)#lldp runR5(config)#no cdp run R5#sh cdp neighbor detail R5#sh lldp neighbor
- BR5(config)#int Gi0/1 R5(config-if)#no cdp enable R5(config-if)#exitR5(config)#no lldp run R5(config)#cdp run R5#sh cdp neighbor R5#sh lldpneighbor
- CR5(config)#int Gi0/1 R5(config-if)#no cdp run R5(config-if)#exit R5(config)#lldp runR5(config)#cdp enable R5#sh cdp neighbor R5#sh lldp neighbor
- DR5(config)#int Gi0/1 R5(config-if)#no cdp enable R5(config-if)#exit R5(config)#no lldp runR5(config)#cdp run R5#sh cdp neighbor detail R5#sh lldp neighbor
89Which two spanning-tree states are bypassed on an interface running PortFast? (Choose two.)
- Adisabled
- Blistening
- Clearning
- Dblocking
- Eforwarding
90DRAG DROP -
Drag and drop the management connection types from the left onto the definitions on the right.
Select and Place:
- ATelnet
SSH
Console
HTTPS - BHTTPS
SSH
Console
Telnet - CHTTPS
Console
SSH
Telnet
- ATelnet
91An engineer is configuring data and voice services to pass through the same port. The designated switch interface fastethernet0/1 must transmit packets using the same priority for data when they are received from the access port of the IP phone. Which configuration must be used?
- Ainterface fastethernet0/1 switchport voice vlan dot1p
- Binterface fastethernet0/1 switchport priority extend cos 7
- Cinterface fastethernet0/1 switchport voice vlan untagged
- Dinterface fastethernet0/1 switchport priority extend trust
92Refer to the exhibit. Which change to the configuration on Switch2 allows the two switches to establish an EtherChannel?

- AChange the LACP mode to desirable
- BChange the protocol to PAgP and use auto mode
- CChange the LACP mode to active
- DChange the protocol to EtherChannel mode on
93Refer to the exhibit. An engineer must configure the interface that connects to PC1 and secure it in away that only PC1 is allowed to use the port. No VLAN tagging can be used except for a voice VLAN. Which command sequence must be entered to configure the switch?

- ASW1(config-if)#switchport mode dynamic auto SW1(config-if)#switchport port-securitySW1(config-if)#switchport port-security violation restrict
- BSW1(config-if)#switchport mode nonegotiate SW1(config-if)#switchport port-securitySW1(config-if)#switchport port-security maximum 1
- CSW1(config-if)#switchport mode access SW1(config-if)#switchport port-security SW1(config-if)#switchport port-security mac-address 0050.7966.6800
- DSW1(config-if)#switchport mode dynamic desirable SW1(config-if)#switchport port-securitymac-address 0050.7966.6800 SW1(config-if)#switchport port-security mac-address sticky
94Which protocol must be implemented to support separate authorization and authentication solutions for wireless APs?
- ARADIUS
- BTACACS+
- C802.1X
- DKerberos
95Which port type supports the spanning-tree portfast command without additional configuration?
- Atrunk ports
- BLayer 3 sub interfaces
- CLayer 3 main interfaces
- Daccess ports
96Refer to the exhibit. What are two conclusions about this configuration? (Choose two.)

- AThe spanning-tree mode is Rapid PVST+
- BThis tea root bridge
- CThe spanning-tree mode is PVST+
- DThe designated port is FastEthernet 2/1
- EThe root port is FastEthernet 2/1
97A Cisco engineer must configure a single switch interface to meet these requirements:
✑ Accept untagged frames and place them in VLAN 20Accept tagged frames in VLAN 30 when CDP detects a Cisco IP phone.
Which command set must the engineer apply?- Aswitchport mode dynamic desirable switchport access vlan 20 switchport trunk allowed vlan30 switchport voice vlan 30
- Bswitchport mode access switchport access vlan 20 switchport voice vlan 30
- Cswitchport mode dynamic auto switchport trunk native vlan 20 switchport trunk allowed vlan30 switchport voice vlan 30
- Dswitchport mode trunk switchport access vlan 20 switchport voice vlan 30
98What does a switch use to build its MAC address table?
- AVTP
- BDTP
- Cingress traffic
- Degress traffic
99Refer to the exhibit. The EtherChannel is configured with a speed of 1000 and duplex as full on both ends of channel group 1. What is the next step to configure the channel on switch A to respond to but not initiate LACP communication?

- Ainterface range gigabitethernet0/0/0-15 channel-group 1 mode on
- Binterface range gigabitethernet0/0/0-15 channel-group 1 mode desirable
- Cinterface port-channel 1 channel-group 1 mode auto
- Dinterface port-channel 1 channel-group 1 mode passive
100Which command entered on a switch configured with Rapid PVST+ listens and learns for a specific time period?
- Aswitch(config)#spanning-tree vlan 1 priority 4096
- Bswitch(config)#spanning-tree vlan 1 hello-time 10
- Cswitch(config)#spanning-tree vlan 1 max-age 6
- Dswitch(config)#spanning-tree vlan 1 forward-time 20
101What must a network administrator consider when deciding whether to configure a new wireless network with APs in autonomous mode or APs running in cloud- based mode?
- AAutonomous mode APs are less dependent on an underlay but more complex to maintain than APs in cloud-based mode.
- BCloud-based mode APs relay on underlays and are more complex to maintain than APs in autonomous mode.
- CCloud-based mode APs are easy to deploy but harder to automate than APs in autonomous mode.
- DAutonomous mode APs are easy to deploy and automate than APs in cloud-based mode.
102When a switch receives a frame for an unknown destination MAC address, how is the frame handled?
- Aflooded to all ports except the origination port
- Bforwarded to the first available port
- Cbroadcast to all ports on the switch
- Dinspected and dropped by the switch
103Which state is bypassed in Rapid PVST+ when PortFast is enabled on a port?
- Ablocking
- Bforwarding
- Clearning
- Ddiscarding
104What happens when a switch receives a frame with a destination MAC address that recently aged out?
- AThe switch floods the frame to all ports in all VLANs except the port that received the frame.
- BThe switch floods the frame to all ports in the VLAN except the port that received the frame.
- CThe switch references the MAC address aging table for historical addresses on the port that received the frame.
- DThe switch drops the frame and learns the destination MAC address again from the port that received the frame.
105What is a function of store-and forward switching?
- AIt reduces latency by eliminating error checking within the frame
- BIt produces an effective level of error-free network traffic using CRCs.
- CIt buffers frames and forwards regardless of errors within the frames.
- DIt forwards a frame by checking only the destination MAC address
106Refer to the exhibit. Switch AccSw1 has just been added to the network along with `PC2`. All VLAN shave been implemented on AccSw2. How must the ports on AccSw2 be configured to establish Layer 2connectivity between `PC1` and `PC2`?

- Ainterface GigabitEthernet1/2 switchport mode access switchport access vlan 2 ! interfaceGigabitEthernet1/24 switchport mode trunk
- Binterface GigabitEthernet1/1 switchport mode access switchport access vlan11 ! interface GigabitEthernet1/24 switchport mode trunk
- Cinterface GigabitEthernet1/24 switchport mode trunk switchport trunk allowed vlan 11, 12 !interface GigabitEthernet1/1 switchport access vlan 11
- Dinterface GigabitEthernet1/2 switchport mode access switchport access vlan 12 ! interfaceGigabitEthernet1/24 switchport mode trunk switchport trunk allowed vlan 11, 12
107Refer to the exhibit. A network engineer must update the configuration on Switch2 so that it sends LLDP packets every minute and the information sent via LLDP is refreshed every 3 minutes. Which configuration must the engineer apply?

- ASwitch2(config)#lldp timer 60 Switch2(config)#lldp tlv-select 180
- BSwitch2(config)#lldp timer 60 Switch2(config)#lldp holdtime 180
- CSwitch2(config)#lldp timer 1 Switch2(config)#lldp holdtime 3
- DSwitch2(config)#lldp timer 1 Switch2(config)#lldp tlv-select 3
108Refer to the exhibit. Switch A is newly configured. All VLANs are present in the VLAN database. The IP phone and PC A on Gi0/1 must be configured for the appropriate VLANs to establish connectivity between the PCs. Which command set fulfills the requirement?

- ASwitchA(config-if)#switchport mode access SwitchA(config-if)#switchportaccess vlan 50 SwitchA(config-if)#switchport voice vlan 51
- BSwitchA(config-if)#switchport mode trunk SwitchA(config-if)#switchport trunk allowed vlanadd 50, 51 SwitchA(config-if)#switchport voice vlan dot1p
- CSwitchA(config-if)#switchport mode trunk SwitchA(config-if)#switchport trunk allowed vlan50, 51 SwitchA(config-if)#mis qos trust cos
- DSwitchA(config-if)#switchport mode access SwitchA(config-if)#switchport access vlan 50SwitchA(config-if)#switchport voice vlan untagged
109Refer to the exhibit. Two new switches are being installed. The remote monitoring team uses the support network to monitor both switches. Which configuration is the next step to establish a Layer 2connection between the two PCs?

- ASwitchA(config)#interface GigabitEthernet0/1 SwitchA(config-if)#switchport access vlan 500SwitchB(config)#interface GigabitEthernet0/1 SwitchB(config-if)#switchport access vlan 500
- BSwitchA(config)#interface GigabitEthernet0/1 SwitchA(config-if)#switchport mode trunkSwitchB(config)#interface GigabitEthernet0/1 SwitchB(config-if)#switchport mode trunk
- CSwitchA(config)#interface GigabitEthernet0/0 SwitchA(config-if)#switchporttrunk allowed vlan 500, 550 SwitchB(config)#interface GigabitEthernet0/0SwitchB(config-if)#switchport trunk allowed vlan 500, 550
- DSwitchA(config)#interface GigabitEthernet0/0 SwitchA(config-if)#spanning-tree portfastSwitchA(config-if)#spanning-tree bpduguard enable SwitchB(config)#interface GigabitEthernet0/0 SwitchB(config-if)#spanning-tree portfast SwitchB(config-if)#spanning-tree bpduguard enable
110Refer to the exhibit. An engineer is configuring a new Cisco switch, NewSW, to replace SW2. The detail shave been provided:
*SW1 and SW2 are third-party devices without support for trunk ports.
*The existing connections must be maintained between PC1, PC2, and PC3.
*Allow the switch to pass traffic from future VLAN 10.
Which configuration must be applied?
- ANewSW(config)#interface f0/0 NewSW(config-if)#switchport mode trunk NewSW(config-if)#switchport trunk native vlan 10 NewSW(config-if)#switchport trunk native vlan 10
- BNewSW(config)#interface f0/0 NewSW(config-if)#switchport mode access NewSW(config-if)#switchport trunk allowed vlan 2, 10 NewSW(config-if)#switchport trunk native vlan 2
- CNewSW(config)#interface f0/0 NewSW(config-if)#switchport mode access NewSW(config-if)#switchport trunk allowed vlan 2, 10 NewSW(config-if)#switchport trunk native vlan 10
- DNewSW(config)#interface f0/0 NewSW(config-if)#switchport mode trunkNewSW(config-if)#switchport trunk allowed vlan 2, 10 NewSW(config-if)#switchport trunk native vlan 2
111Which WLC interface provides out-of-band management in the Cisco Unified Wireless Network Architecture?
- AAP-Manager
- Bservice port
- Cdynamic
- Dvirtual
112Refer to the exhibit. The network engineer is configuring a new WLAN and is told to use a setup password for authentication instead of the RADIUS servers. Which additional set of tasks must the engineer perform to complete the configuration?

- ADisable PMF Enable PSK Enable 802.1x
- BSelect WPA Policy Enable CCKM Enable PSK
- CSelect WPA Policy Select WPA2 Policy Enable FT PSK
- DSelect WPA2 Policy Disable PMF Enable PSK
113Which mode must be set for Aps to communicate to a Wireless LAN Controller using the Control and Provisioning of Wireless Access Points (CAPWAP) protocol?
- Aroute
- Bbridge
- Clightweight
- Dautonomous
114Which switch technology establishes a network connection immediately when it is plugged in?
- APortFast
- BBPDU guard
- CUplinkFast
- DBackboneFast
115Which command on a port enters the forwarding state immediately when a PC is connected to it?
- Aswitch(config)#spanning-tree portfast default
- Bswitch(config)#spanning-tree portfast bpduguard default
- Cswitch(config-if)#spanning-tree portfast trunk
- Dswitch(config-if)#no spanning-tree portfast
116If a switch port receives a new frame while it is actively transmitting a previous frame, how does it process the frames?
- AThe new frame is delivered first, the previous frame is dropped, and a retransmission request is sent
- BThe previous frame is delivered, the new frame is dropped, and a retransmission request is sent
- CThe new frame is placed in a queue for transmission after the previous frame
- DThe two frames are processed and delivered at the same time
117Refer to the exhibit. The entire MAC address table for SW1 is shown here:
What does SW1 do when Br-4 sends a frame for Br-2
- AIt performs a lookup in the MAC address table for Br-4 and discards toe frame due to a missing entry.
- BIt floods the frame out or all ports except on the port where Br-2 is connected.
- CIt Inserts the source MAC address and port into the forwarding table and forwards the frame to Br-2.
- DIt maps the Layer 2 MAC address for Fa0/3 to the Layer 3 IP address and towards the frame.
118How does MAC learning function?
- Aadds unknown source MAC addresses to the CAM table
- Bprotects against denial of service attacks
- Cpopulates the ARP table with the egress port
- Dsends an ARP request to locate unknown destinations
119Refer to the exhibit. An engineer is configuring an EtherChannel using LACP between Switches 1 and 2.
Which configuration must be applied so that only Switch 1 sends LACP initiation packets?
- ASwitch1(config-if)#channel-group 1 mode on
Switch2(config-if)#channel-group 1 mode active - BSwitch1(config-if)#channel-group 1 mode active
Switch2(config-if)#channel-group 1 mode passive - CSwitch1(config-if)#channel-group 1 mode passive
Switch2(config-if)#channel-group 1 mode active - DSwitch1(config-if)#channel-group 1 mode on
Switch2(config-if)#channel-group 1 mode passive
- ASwitch1(config-if)#channel-group 1 mode on
120Refer to the exhibit. The entire Marketing-SW1 MAC address table is shown here:
What does the switch do when PC-4 sends a frame to PC-1?
- AIt performs a lookup in the MAC address table and discards the frame due to a missing entry.
- BIt maps the Layer 2 MAC address to the Layer 3 IP address and forwards the frame.
- CIt inserts the source MAC address and port into the table and forwards the frame to PC-1.
- DIt floods the frame out of all ports except on the port where PC-1 is connected.
121Refer to the exhibit. All VLANs are present in the VLAN database. Which command sequence must be applied to complete the configuration?

- Ainterface FastEthernet0/1
switchport mode access
switchport voice vlan 10 - Binterface FastEthernet0/1
switchport trunk native vlan 10
switchport trunk allowed vlan 10,15 - Cinterface FastEthernet0/1
switchport trunk allowed vlan add 10
vlan 10
private-vlan isolated - Dinterface FastEthernet0/1
switchport mode trunk
switchport trunk allowed vlan 10,15
- Ainterface FastEthernet0/1
122Refer to the exhibit. Which switch becomes the root of a spanning tree for VLAN 10 if the primary switch fails and all links are of equal speed?

- ASW1
- BSW2
- CSW3
- DSW4
123What does the switch do when it receives the frame from host A?

- AIt floods the frame out of all ports except port Fa0/1
- BIt experiences a broadcast storm
- CIt shuts down the port Fa0/1 and places it in err-disable mode
- DIt drops the frame from the switch CAM table
124Refer to the exhibit. Which switch becomes the root of the spanning tree?

- ASwitch 1
- BSwitch 2
- CSwitch 3
- DSwitch 4
125Which channel-group mode must be configured when multiple distribution interfaces connected to a WLC are bundled?
- AChannel-group mode passive.
- BChannel-group mode on.
- CChannel-group mode desirable.
- DChannel-group mode active.
126Refer to the exhibit. Which switch become the root of a spanning tree for VLAN 20 if all links are of equal speed?

- ASW1
- BSW2
- CSW3
- DSW4
127Which Layer 2 switch function encapsulates packets for different VLANs so that the packets transverse the same port and maintain traffic separation between the VLANs.
- AVLAN marking
- BVLAN numbering
- CVLAN DSCP
- DVLAN tagging
128Which value is the unique identifier that an access point uses to establish and maintain wireless connectivity to wireless network devices?
- AVLAN ID
- BSSID
- CRFID
- DWLAN ID
129An engineer must configure neighbor discovery between the company router and an ISP.
interface gigabitethernet0/0
description Circuit-ATT4139-84320
duplex full
speed 1000
media-type gbic
negotiation auto
lldp transmit
lldp receive
What is the next step to complete the configuration if the ISP uses a third-party router?- AEnable LLDP globally.
- BDisable CDP on gi0/0.
- CEnable LLDP TLVs on the ISP router.
- DDisable auto-negotiation.
130DRAG DROP -
Drag and drop the facts about wireless architectures from the left onto the types of access point on the right. Not all options are used.
Select and Place:
- ACloud-Based Access Point
Managed from a Web-based dashboard.
Supports automatic deployment.
Lightweight Access Point
Configured and managed by a WLC.
Supports different operational modes. - BCloud-Based Access Point
Managed from a Web-based dashboard.
Configured and managed by a WLC.
Lightweight Access Point
Supports automatic deployment.
Supports different operational modes. - CCloud-Based Access Point
Supports different operational modes.
Configured and managed by a WLC.
Lightweight Access Point
Supports automatic deployment.
Managed from a Web-based dashboard.
- ACloud-Based Access Point
131What is a function of MAC learning on a switch?
- AMAC address learning is disabled by default on all VLANs.
- BFrames received for a destination MAC address not listed in the address table are dropped.
- CThe MAC address table is used to populate the ARP table.
- DA static MAC address is manually added to the MAC table.
132What does a switch do when it receives a frame whose destination MAC address is missing from the MAC address table?
- AIt changes the checksum of the frame to a value that indicates an invalid frame.
- BIt updates the CAM table with the destination MAC address of the frame.
- CIt appends the table with a static entry for the MAC and shuts down the port.
- DIt floods the frame unchanged across all remaining ports in the incoming VLAN.
133By default, how long will the switch continue to know a workstation MAC address after the workstation stops sending traffic?
- A200 seconds
- B300 seconds
- C600 seconds
- D900 seconds
134A project objective is to minimize the association time to the different access points as mobile devices move around the office. The ideal solution must cover numerous devices and device types, including laptops, mobile phones, tablets and wireless printers. What must be configured?
- A802.11v BSS Max Idle Service
- B802.11v Disassociation Imminent
- C802.11ax BSS configure
- D802.11k neighbor List Dual Band
135Which two protocols are used by an administrator for authentication and configuration on access points? (Choose two.)
- A802.1Q
- BRADIUS
- CKerberos
- DTACACS+
- E802.1x
136DRAG DROP -
Drag and drop the statements about access-point modes from the left onto the corresponding modes on the right.
Select and Place:
- AMonitor
It supports software that analyzes wireless frames on a remote device.
It enables enhanced RFID-tag location tracking.
Sensor
It supports analytics for wireless performance testing.
It captures and forwards packets on a specific wireless channel.
Sniffer
It supports real-time Wi‑Fi client troubleshooting when network engineers are offsite.
It provides air-quality data and interference detection across all enabled channels. - BMonitor
It provides air-quality data and interference detection across all enabled channels.
It captures and forwards packets on a specific wireless channel.
Sensor
It supports analytics for wireless performance testing.
It enables enhanced RFID-tag location tracking.
Sniffer
It supports real-time Wi‑Fi client troubleshooting when network engineers are offsite.
It supports software that analyzes wireless frames on a remote device. - CMonitor
It provides air-quality data and interference detection across all enabled channels.
It captures and forwards packets on a specific wireless channel.
Sensor
It enables enhanced RFID-tag location tracking.
It supports software that analyzes wireless frames on a remote device.
Sniffer
It supports real-time Wi‑Fi client troubleshooting when network engineers are offsite.
It supports analytics for wireless performance testing.
- AMonitor
137A WLC sends alarms about a rogue AP, and the network administrator verifies that the alarms are caused by a legitimate autonomous AP. How must the alarms be stopped for the MAC address of the AP?
- ARemove the AP from WLC management
- BPlace the AP into manual containment.
- CManually remove the AP from Pending state.
- DSet the AP Class Type to Friendly.
138What is one reason to implement LAG on a Cisco WLC?
- Ato increase security and encrypt management frames
- Bto enable connected switch ports to failover and use different VLANs
- Cto provide link redundancy and load balancing
- Dto allow for stateful and link-state failover
139When an access point is seeking to join wireless LAN controller, which message is sent to the AP-Manager interface?
- ADiscovery response
- BDHCP request
- CDHCP discover
- DDiscovery request
140Refer to the exhibit. A network engineer configures the Cisco WLC to authenticate local wireless clients against a RADIUS server. Which task must be performed to complete the process?

- AChange the Support for CoA to Enabled
- BSelect Enable next to Management
- CSelect Enable next to Network User
- DChange the Server Status to Disabled
141After installing a new Cisco ISE server which task must the engineer perform on the Cisco WLC to connect wireless clients on a specific VLAN based on their credentials?
- ADisable the LAG Mode on Next Reboot.
- BEnable the Event Driven RRM.
- CEnable the Allow AAA Override.
- DEnable the Authorize MIC APs against auth-list or AAA
142Refer to the exhibit. Router R1 is running three different routing protocols. Which route characteristic is used by the router to forward the packet that it receives for destination IP 172.16.32.1?

- Alongest prefix
- Badministrative distance
- Ccost
- Dmetric
143Refer to the exhibit. Router R1 Fa0/0 cannot ping router R3 Fa0/1. Which action must be taken in routerR1 to help resolve the configuration issue?

- Aset the default gateway as 20.20.20.2
- Bconfigure a static route with Fa0/1 as the egress interface to reach the 20.20.2.0/24 network
- Cconfigure a static route with 10.10.10.2 as the next hop to reach the20.20.20.0/24 network
- Dset the default network as 20.20.20.0/24
144By default, how does EIGRP determine the metric of a route for the routing table?
- AIt uses the bandwidth and delay values of the path to calculate the route metric.
- BIt uses a default metric of 10 for all routes that are learned by the router.
- CIt counts the number of hops between the receiving and destination routers and uses that value as the metric.
- DIt uses a reference bandwidth and the actual bandwidth of the connected link to calculate the route metric.
145Router R1 must send all traffic without a matching routing-table entry to 192.168.1.1. Which configuration accomplishes this task?
- AR1#config t R1(config)#ip routing R1(config)#ip route default-route 192.168.1.1
- BR1#config t R1(config)#ip routing R1(config)#ip route 192.168.1.1 0.0.0.0 0.0.0.0
- CR1#config t R1(config)#ip routing R1(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.1
- DR1#config t R1(config)#ip routing R1(config)#ip default-gateway 192.168.1.1
146A packet is destined for `10.10.1.22`. Which static route does the router choose to forward the packet?
- Aip route 10.10.1.0 255.255.255.240 10.10.255.1
- Bip route 10.10.1.20 255.255.255.252 10.10.255.1
- Cip route 10.10.1.16 255.255.255.252 10.10.255.1
- Dip route 10.10.1.20 255.255.255.254 10.10.255.1
147Refer to the exhibit. How does the router manage traffic to 192.168.12.16?
EIGRP: 192.168.12.0/24
RIP: 192.168.12.0/27
OSPF: 192.168.12.0/28- AIt chooses the EIGRP route because it has the lowest administrative distance.
- BIt load-balances traffic between all three routes.
- CIt chooses the OSPF route because it has the longest prefix inclusive of the destination address.
- DIt selects the RIP route because it has the longest prefix inclusive of the destination address.
148What are two reasons for an engineer to configure a floating static route? (Choose two.)
- Ato enable fallback static routing when the dynamic routing protocol fails
- Bto route traffic differently based on the source IP of the packet
- Cto automatically route traffic on a secondary path when the primary path goes down
- Dto support load balancing via static routing
- Eto control the return path of traffic that is sent from the router
149Refer to the exhibit. How does router R1 handle traffic to 192.168.10.16?
R1# show ip route
D 192.168.10.0/24 [90/2679326] via 192.168.1.1
R 192.168.10.0/27 [120/3] via 192.168.1.2
O 192.168.10.0/23 [110/2] via 192.168.1.3
i L1 192.168.10.0/13 [115/30] via 192.168.1.4- AIt selects the IS-IS route because it has the shortest prefix inclusive of the destination address
- BIt selects the RIP route because it has the longest prefix inclusive of the destination address
- CIt selects the OSPF route because it has the lowest cost
- DIt selects the EIGRP route because it has the lowest administrative distance
150Refer to the exhibit. A router received these five routes from different routing information sources. Which two routes does the router install in its routing table?
IBGP route 10.0.0.0/30
RIP route 10.0.0.0/30
OSPF route 10.0.0.0/16
OSPF route 10.0.0.0/30
EIGRP route 10.0.0.0/32- AOSPF route 10.0.0.0/30
- BIBGP route 10.0.0.0/30
- COSPF route 10.0.0.0/16
- DEIGRP route 10.0.0.1/32
- ERIP route 10.0.0.0/30
151Refer to the exhibit. To which device does Router1 send packets that are destined to host 10.10.13.165?

- ARouter2
- BRouter3
- CRouter4
- DRouter5
152R1 has learned route 10.10.10.0/24 via numerous routing protocols. Which route is installed?
- Aroute with the next hop that has the highest IP
- Broute with the lowest cost
- Croute with the lowest administrative distance
- Droute with the shortest prefix length
153Which two minimum parameters must be configured on an active interface to enable OSPFv2 to operate? (Choose two.)
- AOSPF process ID
- BOSPF MD5 authentication key
- COSPF stub flag
- DIPv6 address
- EOSPF area
154Refer to the exhibit. What commands are needed to add a sub-interface to Ethernet0/0 on R1 to allow for VLAN 20, with IP address 10.20.20.1/24?

- AR1(config)#interface ethernet0/0 R1(config-if)#encapsulation dot1q 20 R1(config-if)#ipaddress 10.20.20.1 255.255.255.0
- BR1(config)#interface ethernet0/0.20 R1(config-if)#encapsulation dot1q 20R1(config-if)#ip address 10.20.20.1 255.255.255.0
- CR1(config)#interface ethernet0/0.20 R1(config-if)#ip address 10.20.20.1 255.255.255.0
- DR1(config)#interface ethernet0/0 R1(config-if)#ip address 10.20.20.1 255.255.255.0
155Refer to the exhibit. What does router R1 use as its OSPF router-ID?

- A10.10.1.10
- B10.10.10.20
- C172.16.15.10
- D192.168.0.1
156Refer to the exhibit. The loopback1 interface of the Atlanta router must reach the loopback3 interface of the Washington router. Which two static host routes must be configured on the New York router?(Choose two.)

- Aipv6 route 2000::3/128 s0/0/0
- Bipv6 route 2000::1/128 s0/0/1
- Cipv6 route 2000::1/128 2012::1
- Dipv6 route 2000::1/128 2012::2
- Eipv6 route 2000::3/128 2023::3
157Refer to the exhibit. After the configuration is applied, the two routers fail to establish an OSPF neighbor relationship. What is the reason for the problem?

- AThe OSPF process IDs are mismatched
- BThe network statement on Router1 is misconfigured
- CRouter2 is using the default hello timer
- DThe OSPF router IDs are mismatched
158Refer to the exhibit. Which route type is configured to reach the Internet?

- Afloating static route
- Bhost route
- Cnetwork route
- Ddefault route
159Refer to the exhibit. Which path is used by the router for Internet traffic?

- A209.165.200.0/27
- B0.0.0.0/0
- C10.10.13.0/24
- D10.10.10.0/28
160When OSPF learns multiple paths to a network, how does it select a route?
- AFor each existing interface, it adds the metric from the source router to the destination to calculate the route with the lowest bandwidth.
- BIt counts the number of hops between the source router and the destination to determine the route with the lowest metric.
- CIt divides a reference bandwidth of 100 Mbps by the actual bandwidth of the exiting interface to calculate the route with the lowest cost.
- DIt multiplies the active K values by 256 to calculate the route with the lowest metric.
161When a floating static route is configured, which action ensures that the backup route is used when the primary route fails?
- AThe administrative distance must be higher on the primary route so that the backup route becomes secondary.
- BThe default-information originate command must be configured for the route to be installed into the routing table.
- CThe floating static route must have a lower administrative distance than the primary route so it is used as a backup.
- DThe floating static route must have a higher administrative distance than the primary route so it is used as a backup
162Refer to the exhibit. The show ip ospf interface command has been executed on R1. How is OSPF configured?

- AA point-to-point network type is configured.
- BThe interface is not participating in OSPF.
- CThe default Hello and Dead timers are in use.
- DThere are six OSPF neighbors on this interface.
163A user configured OSPF and advertised the Gigabit Ethernet interface in OSPF. By default, to which type of
OSPF network does this interface belong?- Apoint-to-multipoint
- Bpoint-to-point
- Cbroadcast
- Dnonbroadcast
164Which attribute does a router use to select the best path when two or more different routes to the same destination exist from two different routing protocols?
- Adual algorithm
- Bmetric
- Cadministrative distance
- Dhop count
165Router A learns the same route from two different neighbors; one of the neighbor routers is an OSPF neighbor, and the other is an EIGRP neighbor. What is the administrative distance of the route that will be installed in the routing table?
- A20
- B90
- C110
- D115
166Refer to the exhibit. An engineer is bringing up a new circuit to the MPLS provider on the Gi0/1interface of Router 1. The new circuit uses eBGP and learns the route to VLAN25 from the BGP path. What is the expected behavior for the traffic flow for route 10.10.13.0/25?

- ATraffic to 10.10.13.0/25 is load balanced out of multiple interfaces.
- BTraffic to 10.10.13.0/25 is asymmetrical.
- CRoute 10.10.13.0/25 is updated in the routing table as being learned from interface Gi0/1.
- DRoute 10.10.13.0/25 learned via the Gi0/0 interface remains in the routing table.
167Which two actions influence the EIGRP route selection process? (Choose two.)
- AThe advertised distance is calculated by a downstream neighbor to inform the local router of the bandwidth on the link.
- BThe router calculates the feasible distance of all paths to the destination route.
- CThe router must use the advertised distance as the metric for any given route.
- DThe router calculates the best backup path to the destination route and assigns it as the feasible successor.
- EThe router calculates the reported distance by multiplying the delay on the exiting interface by 256.
168Refer to the exhibit. If OSPF is running on this network, how does Router2 handle traffic from Site B to10.10.13.128/25 at Site A?

- AIt sends packets out of interface Fa0/1 only.
- BIt sends packets out of interface Fa0/2 only.
- CIt load-balances traffic out of Fa0/1 and Fa0/2.
- DIt cannot send packets to 10.10.13.128/25.
169Which two outcomes are predictable behaviors for HSRP? (Choose two.)
- AThe two routers negotiate one router as the active router and the other as the standby router.
- BThe two routers share the same interface IP address, and default gateway traffic is load-balanced between them.
- CThe two routers synchronize configurations to provide consistent packet forwarding.
- DEach router has a different IP address, both routers act as the default gateway on the LAN, and traffic is load-balanced between them.
- EThe two routers share a virtual IP address that is used as the default gateway for devices on the LAN.
170Refer to the exhibit. An engineer is configuring the New York router to reach the Lo1 interface of the Atlanta router using interface Se0/0/0 as the primary path.
Which two commands must be configured on the New York router so that it reaches the Lo1 interface of the Atlanta router via Washington when the link between
New York and Atlanta goes down? (Choose two.)
- AIpv6 route 2000::1/128 2012::1
- BIpv6 route 2000::1/128 2012::1 5
- CIpv6 route 2000::1/128 2012::2
- DIpv6 route 2000::1/128 2023::2 5
- EIpv6 route 2000::1/128 2023::3 5
171How does HSRP provide first hop redundancy?
- AIt load-balances Layer 2 traffic along the path by flooding traffic out all interfaces configured with the same VLAN.
- BIt uses a shared virtual MAC and a virtual IP address to a group of routers that serve as the default gateway for hosts on a LAN.
- CIt forwards multiple packets to the same destination over different routed links in the data path.
- DIt load-balances traffic by assigning the same metric value to more than one route to the same destination in the IP routing table.
172Refer to the exhibit. Which action establishes the OSPF neighbor relationship without forming an adjacency?

- Amodify hello interval
- Bmodify process ID
- Cmodify priority
- Dmodify network type
173Which command must you enter to guarantee that an HSRP router with higher priority becomes the HSRP primary router after it is reloaded?
- Astandby 10 preempt
- Bstandby 10 version 1
- Cstandby 10 priority 150
- Dstandby 10 version 2
174Which command should you enter to verify the priority of a router in an HSRP group?
- Ashow hsrp
- Bshow sessions
- Cshow interfaces
- Dshow standby
175Refer to the exhibit. Which command would you use to configure a static route on Router1 to network192.168.202.0/24 with a nondefault administrative distance?

- Arouter1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 1
- Brouter1(config)#ip route 192.168.202.0 255.255.255.0 192.168.201.2 5
- Crouter1(config)#ip route 1 192.168.201.1 255.255.255.0 192.168.201.2
- Drouter1(config)#ip route 5 192.168.202.0 255.255.255.0 192.168.201.2
176Which of the following dynamic routing protocols are Distance Vector routing protocols?
- AIS-IS
- BEIGRP
- COSPF
- DBGP
- ERIP
177You have configured a router with an OSPF router ID, but its IP address still reflects the physical interface. Which action can you take to correct the problem in the least disruptive way?
- AReload the OSPF process
- BSpecify a loopback address
- CReboot the router
- DSave the router configuration
178Which command should you enter to view the error log in an EIGRP for IPv6 environment?
- Ashow ipv6 eigrp neighbors
- Bshow ipv6 eigrp topology
- Cshow ipv6 eigrp traffic
- Dshow ipv6 eigrp events
179Refer to the exhibit. Router R1 must be configured to reach the 10.0.3.0/24 network from the 10.0.1.0/24segment. Which command must be used to configure the route?

- Aroute add 10.0.3.0 0.255.255.255 10.0.4.2
- Bip route 10.0.3.0 0.255.255.255 10.0.4.2
- Croute add 10.0.3.0 mask 255.255.255.0 10.0.4.3
- Dip route 10.0.3.0 255.255.255.0 10.0.4.3
180Refer to the exhibit. Which two statements about the network environment of router must be true? (Choose two.)

- AThe EIGRP administrative distance was manually changed from 90 to 170.
- BThere are 20 different network masks within the 10.0.0.0/8 network.
- CTen routes are equally load-balanced between Te0/1/0.100 and Te0/2/0.100.
- DThe 10.0.0.0/8 network was learned via external EIGRP.
- EA static default route to 10.85.33.14 was defined.
181Which two statements about exterior routing protocols are TRUE? (Choose two.)
- AThey determine the optimal within an autonomous system.
- BThey determine the optimal path between autonomous systems.
- CBGP is the current standard exterior routing protocol.
- DMost modern networking supports both EGP and BGP for external routing.
- EMost modern network routers support both EGP and EIGRP for external routing.
182You have two paths for the 10.10.10.0 network - one that has a feasible distance of 3072 and the other of 6144. What do you need to do to load balance your EIGRP routes?
- AChange the maximum paths to 2
- BChange the configuration so they both have the same feasible distance
- CChange the variance for the path that has a feasible distance of 3072 to 2
- DChange the IP addresses so both paths have the same source IP address
183DRAG DROP -
Drag each route source from the left to the numbers on the right. Beginning with the lowest and ending with the highest administrative distance.
Select and Place:
- Aconnected
static
EBGP
EIGRP
OSPF
RIP - Bstatic
connected
RIP
EIGRP
OSPF
EBGP - Cstatic
connected
RIP
EBGP
OSPF
EIGRP
- Aconnected
184Which two circumstances can prevent two routers from establishing an OSPF neighbor adjacency? (Choose two.)
- Amismatched autonomous system numbers
- Ban ACL blocking traffic from multicast address 224.0.0.10
- Cmismatched process IDs
- Dmismatched hello timers and dead timers
- Euse of the same router ID on both devices
185Which three describe the reasons large OSPF networks use a hierarchical design? (Choose three.)
- Ato speed up convergence
- Bto reduce routing overhead
- Cto lower costs by replacing routers with distribution layer switches
- Dto decrease latency by increasing bandwidth
- Eto confine network instability to single areas of the network
- Fto reduce the complexity of router configuration
186Refer to the exhibit. If R1 receives a packet destined to 172.16.1.1, to which IP address does it send the packet?

- A192.168.14.4
- B192.168.12.2
- C192.168.13.3
- D192.168.15.5
187Refer to the exhibit. On R1 which routing protocol is in use on the route to 192.168.10.1?

- ARIP
- BOSPF
- CIGRP
- DEIGRP
188Refer to the exhibit. Which Command do you enter so that R1 advertises the loopback0 interface to the BGP Peers?
R1
interface Loopback0
ip address 172.16.1.33 255.255.255.224
interface FastEthernet0/0
ip address 192.168.12.1 255.255.255.0
router bgp 100
neighbor 192.168.12.2 remote-as 100- ANetwork 172.16.1.32 mask 255.255.255.224
- BNetwork 172.16.1.0 0.0.0.255
- CNetwork 172.16.1.32 255.255.255.224
- DNetwork 172.16.1.33 mask 255.255.255.224
- ENetwork 172.16.1.32 mask 0.0.0.31
- FNetwork 172.16.1.32 0.0.0.31
189Refer to exhibit. What Administrative distance has route to 192.168.10.1?

- A1
- B90
- C110
- D120
190Which value is used to determine the active router in an HSRP default configuration?
- ARouter loopback address
- BRouter IP address
- CRouter priority
- DRouter tracking number
191Refer to the exhibit. If RTR01 is configured as shown, which three addresses will be received by other routers that are running EIGRP on the network? (Choose three.)
RTR01(config)#router eigrp 103
RTR01(config-router)#network 10.4.3.0
RTR01(config-router)#network 172.16.4.0
RTR01(config-router)#network 192.168.2.0
RTR01(config-router)#auto-summary- A192.168.2.0
- B10.4.3.0
- C10.0.0.0
- D172.16.0.0
- E172.16.4.0
- F192.168.0.0
192Which configuration command can you apply to a HSRP router so that its local interface becomes active if all other routers in the group fail?
- Ano additional config is required
- Bstandby 1 track ethernet
- Cstandby 1 preempt
- Dstandby 1 priority 250
193Which two statements about eBGP neighbor relationships are true? (Choose two.)
- AThe two devices must reside in different autonomous systems
- BNeighbors must be specifically declared in the configuration of each device
- CThey can be created dynamically after the network statement is configured
- DThe two devices must reside in the same autonomous system
- EThe two devices must have matching timer settings
194Refer to the exhibit. How will the router handle a packet destined for 192.0.2.156?

- AThe router will forward the packet via either Serial0 or Serial1.
- BThe router will return the packet to its source.
- CThe router will forward the packet via Serial2.
- DThe router will drop the packet.
195Which statements describe the routing protocol OSPF? (Choose three.)
- AIt supports VLSM.
- BIt is used to route between autonomous systems.
- CIt confines network instability to one area of the network.
- DIt increases routing overhead on the network.
- EIt allows extensive control of routing updates.
- FIt is simpler to configure than RIP v2.
196Refer to the exhibit. After you apply the given configurations to R1 and R2 you notice that OSPFv3 fails to start.
R1
ipv6 unicast-routing
interface FastEthernet0/0
no ip address
ipv6 enable
ipv6 address 3001:DBB:13::1/64
ipv6 ospf 1 area 0
ipv6 router ospf 1
router-id 172.16.1.1
R2
ipv6 unicast-routing
interface FastEthernet0/0
no ip address
ipv6 enable
ipv6 address 2001:DBB:12::12/64
ipv6 ospf 1 area 3
ipv6 router ospf 1
router-id 172.16.3.3- AThe area numbers on R1 and R2 are mismatched
- BThe IPv6 network addresses on R1 and R2 are mismatched
- CThe autonomous system numbers on R1 and R2 are mismatched
- DThe router ids on R1 and R2 are mismatched
197Which command is used to display the collection of OSPF link states?
- Ashow ip ospf link-state
- Bshow ip ospf lsa database
- Cshow ip ospf neighbors
- Dshow ip ospf database
198Refer to the exhibit. A network associate has configured OSPF with the command:
City(config-router)# network 192.168.12.64 0.0.0.63 area 0
After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? (Choose three.)
- AFastEthernet0 /0
- BFastEthernet0 /1
- CSerial0/0
- DSerial0/1.102
- ESerial0/1.103
- FSerial0/1.104
199Refer to the exhibit. C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

- AThese commands need to be added to the configuration: C-router(config)# router eigrp 123C-router(config-router)# network 172.19.0.0
- BThese commands need to be added to the configuration: C-router(config)# router ospf 1 C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
- CThese commands need to be added to the configuration: C-router(config)# router rip C-router(config-router)# network 172.19.0.0
- DNo further routing configuration is required.
200Refer to the exhibit. Which address and mask combination represents a summary of the routes learned by EIGRP?
Gateway of last resort is not set
192.168.25.0/30 is subnetted, 4 subnets
D 192.168.25.20 [90/2681856] via 192.168.15.5, 00:00:10, Serial0/1
D 192.168.25.16 [90/1823638] via 192.168.15.5, 00:00:50, Serial0/1
D 192.168.25.24 [90/3837233] via 192.168.15.5, 00:05:23, Serial0/1
D 192.168.25.28 [90/8127323] via 192.168.15.5, 00:06:45, Serial0/1
C 192.168.15.4/30 is directly connected, Serial0/1
C 192.168.2.0/24 is directly connected, FastEthernet0/0- A192.168.25.0 255.255.255.240
- B192.168.25.0 255.255.255.252
- C192.168.25.16 255.255.255.240
- D192.168.25.16 255.255.255.252
- E192.168.25.28 255.255.255.240
- F192.168.25.28 255.255.255.252
Information
- Description
- Quiz on Pepinillo 2, created by TER TER on 22/08/2026.
- Author
- TER TER
- Language
- Español
- Views
- 0
- Rating
- No ratings yet Rate this quiz