Help shape GoConqr. What should we add next?

Quiz

CCNA – Trunking Questions

jonathan rozo 10 questions

Take the quiz

Questions in this quiz (10)

  1. 1QUESTION NO: 82
    Refer to the exhibit.


    A technician is troubleshooting host connectivity issues on the switches. The hosts in VLANs 10 and 15 on Sw11 are unable to communicate with hosts in the same VLANs on Sw12. Hosts in the Admin VLAN are able to communicate. The port-to-VLAN assignments are identical on the two switches. What could be the problem?

    Image for question 1
    1. AThe Fa0/1 port is not operational on one of the switches.
    2. BThe link connecting the switches has not been configured as a trunk.
    3. CAt least one port needs to be configured in VLAN 1 for VLANs 10 and 15 to be able to communicate.
    4. DPort FastEthernet 0/1 needs to be configured as an access link on both switches.
    5. EA router is required for hosts on SW11 in VLANs 10 and 15 to communicate with hosts in the same VLAN on Sw12.
  2. 2QUESTION NO: 32
    In a switched environment, what does the IEEE 802.1Q standard describe?

    1. Athe operation of VTP
    2. Ba method of VLAN trunking
    3. Can approach to wireless LAN communication
    4. Dthe process for root bridge selection
    5. EVLAN pruning
  3. 3QUESTION NO: 69
    Which are valid modes for a switch port used as a VLAN trunk? (Choose three.)

    1. Atransparent
    2. Bauto
    3. Con
    4. Ddesirable
    5. Eblocking
    6. Fforwarding
  4. 4QUESTION NO: 45
    Refer to the exhibit.


    All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?

    Image for question 4
    1. AThe access link needs to be configured in multiple VLANs.
    2. BThe link between the switches is configured in the wrong VLAN.
    3. CThe link between the switches needs to be configured as a trunk.
    4. DVTP is not configured to carry VLAN information between the switches.
    5. ESwitch IP addresses must be configured in order for traffic to be forwarded between the switches.
  5. 5QUESTION NO: 39
    Which IEEE standard protocol is initiated as a result of successful DTP completion in a switch over Fast Ethernet?

    1. A802.3ad
    2. B802.1w
    3. C802.1D
    4. D802.1Q
  6. 6QUESTION NO: 71
    Which three of these statements regarding 802.1Q trunking are correct? (Choose three.)

    1. A802.1Q native VLAN frames are untagged by default.
    2. B802.1Q trunking ports can also be secure ports.
    3. C802.1Q trunks can use 10 Mb/s Ethernet interfaces.
    4. D802.1Q trunks require full-duplex, point-to-point connectivity.
    5. E802.1Q trunks should have native VLANs that are the same at both ends.
  7. 7QUESTION NO: 165
    Refer to the exhibit.


    C-router is to be used as a "router-on-a-stick" to route between the VLANs. All the interfaces have been properly configured and IP routing is operational. The hosts in the VLANs have been configured with the appropriate default gateway. What is true about this configuration?

    Image for question 7
    1. AThese commands need to be added to the configuration:
      C-router(config)# router eigrp 123
      C-router(config-router)# network 172.19.0.0
      These commands need to be added to the configuration:
      C-router(config)# router ospf 1
      C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
    2. BThese commands need to be added to the configuration:
      C-router(config)# router rip
      C-router(config-router)# network 172.19.0.0
    3. CNo further routing configuration is required.
    4. DThese commands need to be added to the configuration:
      C-router(config)# router ospf 1
      C-router(config-router)# network 172.19.0.0 0.0.3.255 area 0
  8. 8QUESTION NO: 173
    Refer to the exhibit.
    What commands must be configured on the 2950 switch and the router to allow communication between host 1 and host 2? (Choose two.)
    Image for question 8
    1. ARouter(config)# interface fastethernet 0/0
      Router(config-if)# ip address 192.168.1.1 255.255.255.0
      Router(config-if)# no shut down
    2. BRouter(config)# interface fastethernet 0/0
      Router(config-if)# no shut down
      Router(config)# interface fastethernet 0/0.1
      Router(config-subif)# encapsulation dot1q 10
      Router(config-subif)# ip address 192.168.10.1 255.255.255.0
      Router(config)# interface fastethernet 0/0.2
      Router(config-subif)# encapsulation dot1q 20
      Router(config-subif)# ip address 192.168.20.1 255.255.255.0
    3. CRouter(config)# router eigrp 100
      Router(config-router)# network 192.168.10.0
      Router(config-router)# network 192.168.20.0
    4. DSwitch1(config)# vlan database
      Switch1(config-vlan)# vtp domain XYZ
      Switch1(config-vlan)# vtp server

      Switch1(config)# interface fastethernet 0/1
      Switch1(config-if)# switchport mode trunk
    5. ESwitch1(config)# interface vlan 1
      Switch1(config-if)# ip default-gateway 192.168.1.1
  9. 9QUESTION NO: 64
    Which two of these are characteristics of the 802.1Q protocol? (Choose two.)


    1. AIt is used exclusively for tagging VLAN frames and does not address network reconvergence following switched network topology changes.
    2. BIt modifies the 802.3 frame header, and thus requires that the FCS be recomputed.
    3. CIt is a Layer 2 messaging protocol which maintains VLAN configurations across networks.
    4. DIt includes an 8-bit field which specifies the priority of a frame.
    5. EIt is a trunking protocol capable of carrying untagged frames.
  10. 10What are the possible trunking modes for a switch port? (Choose three)
    1. Atransparent
    2. Bauto
    3. Con
    4. Ddesirable
    5. Eclient
    6. Fforwarding

Information

Description
Quiz on CCNA – Trunking Questions , created by jonathan rozo on 10/06/2016.
Language
Español
Views
1
Rating
No ratings yet
Rate this quiz
Rate this quiz

More on VLAN Trunking and VTP

Feedback

What is it about?

What should we add next?