Gestalte GoConqr mit. Was sollen wir als Nächstes hinzufügen?

Quiz

List C

Sam Brake 54 Fragen

Quiz starten

Fragen in diesem Quiz (54)

  1. 1Which technological factor determines the impact of a failure domain?

    1. Athe number of layers of the hierarchical network
    2. Bthe number of users on the access layer
    3. Cthe role of the malfunctioning device
    4. Dthe forwarding rate of the switches used on the access layer
  2. 2What is the function of STP in a scalable network?
    1. AIt decreases the size of the failure domain to contain the impact of failures.
    2. BIt protects the edge of the enterprise network from malicious activity.
    3. CIt disables redundant paths to eliminate Layer 2 loops.
    4. Dthe forwarding rate of the switches used on the access layer
  3. 3Which characteristic would most influence a network design engineer to select a multilayer switch over a Layer 2 switch?
    1. Aability to build a routing table
    2. Bability to aggregate multiple ports for maximum data throughput
    3. Cability to have multiple forwarding paths through the switched network based on VLAN number(s)
    4. Dability to provide power to directly-attached devices and the switch itself
  4. 4What are two reasons to install a single 48-port fixed configuration switch, rather than two 24-port fixed configuration switches, in a wiring closet that supports two classrooms? (Choose two.)
    1. Amore power provided to each port
    2. Bmore ports available for end devices
    3. Chigher uplink speeds
    4. Dreduced power and space requirements
    5. Ereduced number of VLANs/broadcast domains
  5. 5What are two requirements when using out-of-band configuration of a Cisco IOS network device? (Choose two.)
    1. AHTTP access to the device
    2. Ba terminal emulation client
    3. CTelnet or SSH access to the device
    4. Da direct connection to the console or AUX port
    5. Ea connection to an operational network interface on the device
  6. 6Which step can be taken to ensure that a switch added to the network does not overwrite the VLAN databases on existing switches in the same VTP domain?
    1. AChange the VTP mode to client.
    2. BReset the switch VTP revision number to 0.
    3. CDelete any configured VLANs and reboot the switch.
    4. DErase the startup configuration and reboot the switch.
  7. 7A network administrator is planning to add a new switch to the network. What should the network administrator do to ensure the new switch exchanges VTP information with the other switches in the VTP domain?
    1. AConfigure the correct VTP domain name and password on the new switch.
    2. BAssociate all ports of the new switch to a VLAN that is not VLAN 1.
    3. CConfigure the VLANs on the new switch.
    4. DConfigure all ports on the new switch to access mode.
  8. 8An administrator was troubleshooting a router-on-a-stick topology and concluded that the problem was related to the configuration of VLANs on the router subinterfaces. Which two commands can the administrator use in the router to identify the problem? (Choose two.)
    1. Ashow controllers
    2. Bshow ip interface
    3. Cshow ip protocols
    4. Dshow running-config
    5. Eshow vlan
  9. 9Refer to the exhibit. The configuration shows commands entered by a network administrator for inter-VLAN routing. However, host PCA cannot communicate with PCB. Which part of the inter-VLAN configuration causes the problem?

    Bild zu Frage 9
    1. Atrunking
    2. Bport mode on the two switch FastEthernet ports
    3. CVLAN configuration
    4. Drouter port configuration
  10. 10Refer to the exhibit. Switch SW-A is to be used as a temporary replacement for another switch in the VTP Student domain. What two pieces of information are indicated from the exhibited output? (Choose two.)

    1. AThe other switches in the domain can be running either VTP version 1 or 2.
    2. BThere is a risk that the switch may cause incorrect VLAN information to be sent through the domain.
    3. CVTP will block frame forwarding on at least one redundant trunk port that is configured on this switch.
    4. DVLAN configuration changes made on this switch will be sent to other devices in the VTP domain.
    5. EThis switch will update its VLAN configuration when VLAN changes are made on a VTP server in the same domain.

Informationen

Beschreibung
Quiz am List C, erstellt von Sam Brake am 30/04/2018.
Sprache
English
Aufrufe
0
Bewertung
Noch keine Bewertungen
Bewerte dieses Quiz
Bewerte dieses Quiz

Feedback

Worum geht es?

Was sollen wir als Nächstes hinzufügen?