Quiz
List C
Crie uma conta grátis para terminar este quiz
Salve seu progresso e veja sua nota final.
Já tem uma conta? Inicie sessão
Perguntas do quiz (54)
1Which technological factor determines the impact of a failure domain?
- Athe number of layers of the hierarchical network
- Bthe number of users on the access layer
- Cthe role of the malfunctioning device
- Dthe forwarding rate of the switches used on the access layer
2What is the function of STP in a scalable network?
- AIt decreases the size of the failure domain to contain the impact of failures.
- BIt protects the edge of the enterprise network from malicious activity.
- CIt disables redundant paths to eliminate Layer 2 loops.
- Dthe forwarding rate of the switches used on the access layer
3Which characteristic would most influence a network design engineer to select a multilayer switch over a Layer 2 switch?
- Aability to build a routing table
- Bability to aggregate multiple ports for maximum data throughput
- Cability to have multiple forwarding paths through the switched network based on VLAN number(s)
- Dability to provide power to directly-attached devices and the switch itself
4What are two reasons to install a single 48-port fixed configuration switch, rather than two 24-port fixed configuration switches, in a wiring closet that supports two classrooms? (Choose two.)
- Amore power provided to each port
- Bmore ports available for end devices
- Chigher uplink speeds
- Dreduced power and space requirements
- Ereduced number of VLANs/broadcast domains
5What are two requirements when using out-of-band configuration of a Cisco IOS network device? (Choose two.)
- AHTTP access to the device
- Ba terminal emulation client
- CTelnet or SSH access to the device
- Da direct connection to the console or AUX port
- Ea connection to an operational network interface on the device
6Which step can be taken to ensure that a switch added to the network does not overwrite the VLAN databases on existing switches in the same VTP domain?
- AChange the VTP mode to client.
- BReset the switch VTP revision number to 0.
- CDelete any configured VLANs and reboot the switch.
- DErase the startup configuration and reboot the switch.
7A network administrator is planning to add a new switch to the network. What should the network administrator do to ensure the new switch exchanges VTP information with the other switches in the VTP domain?
- AConfigure the correct VTP domain name and password on the new switch.
- BAssociate all ports of the new switch to a VLAN that is not VLAN 1.
- CConfigure the VLANs on the new switch.
- DConfigure all ports on the new switch to access mode.
8An administrator was troubleshooting a router-on-a-stick topology and concluded that the problem was related to the configuration of VLANs on the router subinterfaces. Which two commands can the administrator use in the router to identify the problem? (Choose two.)
- Ashow controllers
- Bshow ip interface
- Cshow ip protocols
- Dshow running-config
- Eshow vlan
9Refer to the exhibit. The configuration shows commands entered by a network administrator for inter-VLAN routing. However, host PCA cannot communicate with PCB. Which part of the inter-VLAN configuration causes the problem?

- Atrunking
- Bport mode on the two switch FastEthernet ports
- CVLAN configuration
- Drouter port configuration
10Refer to the exhibit. Switch SW-A is to be used as a temporary replacement for another switch in the VTP Student domain. What two pieces of information are indicated from the exhibited output? (Choose two.)
- AThe other switches in the domain can be running either VTP version 1 or 2.
- BThere is a risk that the switch may cause incorrect VLAN information to be sent through the domain.
- CVTP will block frame forwarding on at least one redundant trunk port that is configured on this switch.
- DVLAN configuration changes made on this switch will be sent to other devices in the VTP domain.
- EThis switch will update its VLAN configuration when VLAN changes are made on a VTP server in the same domain.
11Refer to the exhibit. The network administrator configures both switches as displayed. However, host C is unable to ping host D and host E is unable to ping host F. What action should the administrator take to enable this communication?

- AInclude a router in the topology.
- BAssociate hosts A and B with VLAN 10 instead of VLAN 1.
- CRemove the native VLAN from the trunk.
- DConfigure either trunk port in the dynamic desirable mode.
- EAdd the switchport nonegotiate command to the configuration of SW2.
12What is a characteristic of spanning tree?
- AIt is enabled by default on Cisco switches.
- BIt has a TTL mechanism that works at Layer 2.
- CIt prevents propagation of Layer 2 broadcast frames.
- DIt is used to discover information about an adjacent Cisco device.
13Refer to the exhibit. All the displayed switches are Cisco 2960 switches with the same default priority and operating at the same bandwidth. Which three ports will be STP designated ports? (Choose three.)

- Afa0/9
- Bfa0/10
- Cfa0/11
- Dfa0/13
- Efa0/20
- Ffa0/21
14A set of switches is being connected in a LAN topology. Which STP bridge priority value will make it least likely for the switch to be selected as the root?
- A4096
- B32768
- C61440
- D65535
15Refer to the exhibit. Which switch will be elected the root bridge and which switch will place a port in blocking mode? (Choose two.)

- ASW1 will become the root bridge.
- BSW2 will become the root bridge.
- CSW2 will get a port blocked.
- DSW4 will get a port blocked.
- ESW3 will become the root bridge.
- FSW4 will become the root bridge.
16Which statement is true about the states of the IEEE 802.1D Spanning Tree Protocol?
- APorts are manually configured to be in the forwarding state.
- BPorts listen and learn before going into the forwarding state.
- CPorts must be blocked before they can be placed in the disabled state.
- DIt takes 15 seconds for a port to go from blocking to forwarding.
17Refer to the exhibit. What are the possible port roles for ports A, B, C, and D in this RSTP-enabled network?

- Aalternate, root, designated, root
- Bdesignated, root, alternate, root
- Calternate, designated, root, root
- Ddesignated, alternate, root, root
18 Refer to the exhibit. What are two results of issuing the displayed commands on S1, S2, and S3? (Choose two.)

- AS1 will automatically adjust the priority to be the lowest.
- BS1 will automatically adjust the priority to be the highest.
- CS2 can become root bridge if S3 fails.
- DS2 can become root bridge if S1 fails.
19When the show spanning-tree vlan 33 command is issued on a switch, three ports are shown in the forwarding state. In which two port roles could these interfaces function while in the forwarding state? (Choose two.)
- Adisabled
- Bdesignated
- Croot
- Dalternate
- Eblocked
20Which is a characteristic of EtherChannel?
- AEtherChannel uses physical ports that have been upgraded to provide a faster connection.
- BSTP will not block redundant EtherChannel bundles between two switches.
- CSTP treats all interfaces in a bundle as a single logical link.
- DEtherChannel configuration is applied to each physical port.
21A network administrator has configured an EtherChannel between two switches that are connected via four trunk links. If the physical interface for one of the trunk links changes to a down state, what happens to the EtherChannel?
- AThe EtherChannel will transition to a down state.
- BSpanning Tree Protocol will recalculate the remaining trunk links.
- CThe EtherChannel will remain functional.
- DSpanning Tree Protocol will transition the failed physical interface into forwarding mode.
22What are two load-balancing methods in the EtherChannel technology? (Choose two.)
- Acombination of source port and IP to destination port and IP
- Bsource IP to destination IP
- Csource port to destination port
- Dcombination of source MAC and IP to destination MAC and IP
- Esource MAC to destination MAC
23Which mode configuration setting would allow formation of an EtherChannel link between switches SW1 and SW2 without sending negotiation traffic?
- ASW1: on
SW2: on - BSW1: desirable
SW2: desirable - CSW1: auto
SW2: auto
trunking enabled on both switches - DSW1: auto
SW2: auto
PortFast enabled on both switches - ESW1: passive
SW2: active
- ASW1: on
24Which two parameters must match on the ports of two switches to create a PAgP EtherChannel between the switches? (Choose two.)
- AMAC address
- Bspeed
- CVLAN information
- DPAgP mode
- Eport ID
25A network administrator is analyzing first-hop router redundancy protocols. What is a characteristic of VRRPv3?
- AVRRPv3 is Cisco proprietary.
- BIt supports IPv6 and IPv4 addressing.
- CIt works together with HSRP.
- DIt allows load balancing between routers.
26Refer to the exhibit. A network administrator would like to implement dynamic routing within a small network environment as shown in the exhibit. Which routing protocol would be a viable solution?

- AEIGRP
- BIGRP
- CBGP
- DRIPv1
27What is a key distinction between classful and classless routing protocols?
- AClassful routing protocols are better suited for implementation in discontiguous networks.
- BClassful routing protocols do not send subnet mask information in their routing updates.
- CClassless routing protocols are not scalable.
- DClassless routing protocols do not allow for route summarization.
28What does the SPF algorithm consider to be the best path to a network?
- AThe path with the least number of hops.
- BThe path with the smallest delays.
- CThe path that includes the fastest cumulative bandwidth links.
- DThe path that includes the fastest single bandwidth link.
29Which protocol does EIGRP use for the transportation of EIGRP packets?
- AUser Datagram Protocol
- BReliable Transport Protocol
- CReal-Time Transport Protocol
- DTransmission Control Protocol
30Which two statements are correct about EIGRP acknowledgment packets? (Choose two.)
- AThe packets are sent in response to hello packets.
- BThe packets are used to discover neighbors that are connected on an interface.
- CThe packets are sent as unicast.
- DThe packets require confirmation.
- EThe packets are unreliable.
31What EIGRP packet type is used by EIGRP routers to discover neighbors on directly connected links?
- Ahello
- Bquery
- Cupdate
- Dacknowledgment
32Which statement describes the autonomous system number used in EIGRP configuration on a Cisco router?
- AIt carries the geographical information of the organization.
- BIt functions as a process ID in the operation of the router.
- CIt is a globally unique autonomous system number that is assigned by IANA.
- DIt identifies the ISP that provides the connection to network of the organization.
33What two values must match between two EIGRP directly connected neighbors to establish and maintain an adjacency? (Choose two.)
- Ametric parameters
- Bautonomous system number
- Crouter ID
- Dhello timers
- EArea ID
34Refer to the exhibit. Which two conclusions can be derived from the output? (Choose two.)

- AThere is one feasible successor to network 192.168.1.8/30.
- BThe network 192.168.10.8/30 can be reached through 192.168.11.1.
- CThe reported distance to network 192.168.1.0/24 is 41024256.
- DThe neighbor 172.16.6.1 meets the feasibility condition to reach the 192.168.1.0/24 network.
- ERouter R1 has two successors to the 172.16.3.0/24 network.
35Which command is used to display the bandwidth of an interface on an EIGRP-enabled router?
- Ashow ip route
- Bshow interfaces
- Cshow ip protocols
- Dshow ip interface brief
36An EIGRP router loses the route to a network. Its topology table contains two feasible successors to the same network. What action will the router take?
- AThe DUAL algorithm is recomputed to find an alternate route.
- BThe router uses the default route.
- CThe best alternative backup route is immediately inserted into the routing table.
- DThe router will query neighbors for an alternate route.
37A network engineer examining the operation of EIGRP on a router notices that one particular route is in an active state. What can the engineer determine about this route?
- AData packets to be sent to the specified network will be forwarded on this route.
- BEIGRP query messages are being sent to other routers requesting paths to this network.
- CThe Diffusing Update Algorithm has determined a successor and a feasible successor for this route.
- DThe EIGRP processes are still calculating the administrative distance for this route.
38Refer to the exhibit. What will Router1 do if it receives packets that are destined to network 2001:db8:11:100::/64?

- Adrop the packets
- Bforward the packets to the gateway of last resort
- Csend the packets out interface GigabitEthernet 0/0
- Dsend the packets out interface Serial 0/0/0
39How are externally learned EIGRP routes identified in the routing table?
- AEX
- BO1 E
- CD
- D*
40
A network administrator is configuring EIGRP load balancing with the commands:
Router(config)# router eigrp 1
Router(config-router)# variance 3
Router(config-router)# end
What is a direct result of entering these commands?- AUp to three equal cost routes to the same destination can be installed in the routing table.
- BUp to three unequal cost routes to the same destination can be installed in the routing table.
- CNo matter whether the metric is equal or unequal, up to three routes to the same destination can be installed in the routing table.
- DAny feasible successor routes to the same destination network with a metric, equal to or less than 3 times that of the successor, will be installed in the routing table.
41By default, how many equal cost routes to the same destination can be installed in the routing table of a Cisco router?
- A2
- B4
- C16
- D32
42What is a function of OSPF hello packets?
- Ato send specifically requested link-state records
- Bto discover neighbors and build adjacencies between them
- Cto ensure database synchronization between routers
- Dto request specific link-state records from neighbor routers
43What is the final operational state that will form between an OSPF DR and a DROTHER once the routers reach convergence?
- Afull
- Btwo-way
- Cloading
- Destablished
44A router needs to be configured to route within OSPF Area 0. Which two commands are required to accomplish this? (Choose two.)
- ARouterA(config)# router ospf 0
- BRouterA(config)# router ospf 1
- CRouterA(config-router)# network 192.168.2.0 0.0.0.255 0
- DRouterA(config-router)# network 192.168.2.0 0.0.0.255 area 0
- ERouterA(config-router)# network 192.168.2.0 255.255.255.0 0
45Refer to the exhibit. R1 and R2 are OSPFv3 neighbors. Which address would R1 use as the next hop for packets that are destined for the Internet?

- AFF02::5
- B2001:DB8:ACAD:1::2
- C2001:DB8:C5C0:1::2
- DFE80::21E:BEFF:FEF4:5538
46What does an OSPF area contain?
- Arouters that share the same router ID
- Brouters whose SPF trees are identical
- Crouters that have the same link-state information in their LSDBs
- Drouters that share the same process ID
47What are the only two roles that permit an OSPF router to be configured for summarization? (Choose two.)
- Abackbone router
- Binternal router
- Cdesignated router
- Darea border router
- Eautonomous system boundary router
48Which routing table descriptor is used to identify the OSPF networks advertised by type 1 LSAs?
- AO E2
- BO E1
- CO IA
- DO
49What are two features of OSPF interarea route summarization? (Choose two.)
- AASBRs perform all OSPF summarization.
- BRoutes within an area are summarized by the ABR.
- CABRs advertise the summarized routes into the backbone.
- DType 3 and type 5 LSAs are used to propagate summarized routes by default.
- ERoute summarization results in high network traffic and router overhead.
50Refer to the exhibit. What are three resulting DR and BDR elections for the given topology? (Choose three.)

- AR2 is BDR for segment A.
- BR4 is BDR for segment B.
- CR5 is DR for segment B.
- DR1 is DR for segment A.
- ER3 is DR for segment B.
- FR3 is DBR for segment B.
51What is one reason to use the ip ospf priority command when the OSPF routing protocol is in use?
- Ato activate the OSPF neighboring process
- Bto influence the DR/BDR election process
- Cto provide a backdoor for connectivity during the convergence process
- Dto streamline and speed up the convergence process
52Which statement describes a characteristic of OSPF external routes?
- AThe difference between type 1 and type 2 is in the way the cost of the route is being calculated.
- BType 1 and type 2 external routes in IPv4 networks are represented in the routing table by EX1 and EX2, respectively.
- CA type 2 route is always preferred over a type 1 route for the same destination.
- DThe cost of a type 1 route is always the external cost, regardless of the interior cost to reach that route.
53Refer to the exhibit. A network administrator has configured OSPFv2 on the two Cisco routers as shown. PC1 is unable to communicate with PC2. What should be done to fix the problem?

- AAdd the network 192.168.255.2 0.0.0.0 area 0 command to router R1 and remove the network 192.168.255.1 0.0.0.0 area 0 command.
- BAdd the passive-interface S0/0 command to router R1.
- CAdd the network 192.168.10.0 0.0.0.255 area 0 command to router R1 and remove the network 192.168.10.1 0.0.0.0 area 0 command.
- DAdd the network 192.168.255.0 0.0.0.3 area 0 command to router R1 and remove the network 192.168.255.1 0.0.0.0 area 0 command.
54Which command can be used by an administrator to display a list of interfaces that are enabled for OSPFv3?
- Ashow ipv6 ospf
- Bshow ipv6 neighbor
- Cshow ipv6 route ospf
- Dshow ipv6 protocols
Informações
- Descrição
- Quiz sobre List C, criado por Sam Brake em 30-04-2018.
- Autor
- Sam Brake
- Idioma
- English
- Visualizações
- 0
- Avaliação
- Ainda sem avaliações Avalie este quiz