Gestalte GoConqr mit. Was sollen wir als Nächstes hinzufügen?

Karteikarten

mechanisms

ella stokes Englisch 57 Karten

how do you work out mechanical advantage

Karten in diesem Stapel (57)

  1. 1what is a mechanismA mechanism is simply a device which takes an input motion and force, and outputs a different motion and force
  2. 2what is the point of a mechanismThe point of a mechanism is to make the job easier to do.
  3. 3what are the mechanisms most commonly used in medical systemsThe mechanisms most commonly used in mechanical systems are levers, linkages, cams, gears, and and pulleys.
  4. 4what is a lever and give examples of itA lever is the simplest kind of mechanism. There are three different types of lever. Common examples of each type are the crowbar, the wheelbarrow and the pair of tweezers.
  5. 5what are types of levers calledAll levers are one of three types, usually called classes
  6. 6what does the class of a lever depend onThe class of a lever depends on the relative position of the load, effort and fulcrum:
    The load is the object you are trying to move.
    The effort is the force applied to move the load.
    The fulcrum (or pivot) is the point where the load is pivoted
  7. 7what is a class 1 lever and give an example of itA class 1 lever has the load and the effort on opposite sides of the fulcrum, like a seesaw. Examples of a class-one lever are a pair of pliers and a crowbar.
  8. 8what is a class 2 lever and give an example of itA class 2 lever has the load and the effort on the same side of the fulcrum, with the load nearer the fulcrum. Examples of a class-two lever are a pair of nutcrackers or a wheelbarrow.
  9. 9what do class 1 and class 2 both provideClass 1 and class 2 levers both provide mechanical advantage. This means that they allow you to move a large output load with a small effort.
  10. 10what are load and effort and what are they measured inLoad and effort are forces and are measured in Newtons (N).
  11. 11how do you work out mechanical advantagehow do you work out mechanical advantage
  12. 12how do you work out the velocity ratiohow do you work out the velocity ratio
  13. 13give an example of a class 3 leverThe common example of class 3 levers is a pair of barbeque tongs or a pair of tweezers.
  14. 14why are class 3 levers less commonA class 3 lever does not have the mechanical advantage of class-one levers and class-two levers, so examples are less common.
  15. 15what are linkagesLinkages are mechanisms which allow force or motion to be directed where it is needed
  16. 16what can linkages be used to changeLinkages can be used to change:
    The direction of motion
    The type of motion
    The size of a force
  17. 17what does a linkage consist ofA linkage consists of a system of rods or other rigid materials connected by joints or pivots. The ability of each rod to move will be limited by moving and fixed pivots. The input at one end of the mechanical linkages will be different from the output, in place, speed, direction and other ways.
  18. 18what is a reverse linkageA reverse-motion linkage changes the direction of motion. In the diagram below, note how the linkage looks a little like a "Z". See how the central rod moves around a central fixed pivot. By pulling (or pushing) the linkage in one direction, it creates an exact opposite motion in the other direction. If the fixed pivot was not central, it would create a larger or smaller motion in the opposite direction.what is a reverse linkage
  19. 19what is a parallel linkageA parallel-motion linkage creates an identical parallel motion. In the diagram below, note how the linkage looks a little like an "n". This time, it is the two side rods that move around two central fixed pivots, while the top of the "n" moves freely. By pulling (or pushing) the linkage in one direction, it creates an identical parallel motion at the other end of the linkage.what is a parallel linkage
  20. 20what is a bell-crank linkageA bell-crank linkage changes the direction of movement through 90°. A bell-crank linkage tends to look a little like an "L" or, as shown in the diagram below, a mirror image of an "L". By pulling (or pushing) the linkage in one direction, it creates a similar motion at the other end of the linkage. For example, a bell-crank linkage could be used to turn a vertical movement into horizontal movement, as in a bicycle braking system.what is a bell-crank linkage
  21. 21what is a treadle linkageA treadle linkage shows how linkages can be used to change one type of motion into another. In this case, the rotary motion of the cam moves a parallel-motion linkage. The parallel-motion linkage controls the identical side-to-side, or oscillating motion, of two windscreen wipers.what is a treadle linkage
  22. 22what is a camA cam is a shaped piece of metal or plastic fixed to a rotating shaft.
  23. 23what are the three parts of a cam mechanismA cam mechanism has three parts: cam, slide and follower.
  24. 24how does the cam workThe cam shaft rotates continually, turning the cam. The follower is a rod that rests on the edge of the turning cam.
  25. 25what are the three things the followers can doThe follower is free to move up and down, but is prevented from moving from side to side by a slide or guide, so the follower can only do three things:
    Rise (move up)
    Fall (move down) or
    Dwell (remain stationary)
  26. 26what does the followers pattern of movement depend onThe follower's pattern of movement depends on the profile or outside edge of the cam that it follows. If the cam is perfectly round and the fixed shaft is in the centre of the cam, the follower will dwell
  27. 27what happens if the cam is a different shapeBut if the cam is a different shape, and/or the shaft is not central, the follower will rise or fall.
  28. 28what determines how often and how quick the follower moves?How often and how quickly the follower moves is determined by the shape of the cam and the position of the shaft.
  29. 29what shapes do cams come inCams come in many different shapes - for example pear-shaped, triangular or square.
  30. 30why might the cam have chunks removedThe cam may have a chunk or chunks removed, so that the follower falls into a gap and is then is pushed out again.
  31. 31what is a pear shaped camThe pear shape of this cam means that for half the cycle, the follower will dwell. Then, as the pointed part of the cam approaches, the follower is pushed up (rises), then, as the point passes, falls and dwells - and the cycle starts again.
  32. 32what is an electric camThe eccentric cam is perfectly circular, but the rotating shaft is off-centre, which affects how it turns. This type of cam produces a smooth, symmetrical rise and fall motion in the follower, which never pauses to dwell.
  33. 33what is a drop camWith a drop cam the shaft is central in a perfectly round cam, which has a chunk removed. The follower will dwell for most of the cycle, until it suddenly falls into the removed section, then rises again as the cam regains its circular shape.
  34. 34what is a number of gears connected calledA number of gears connected together are called a gear train
  35. 35what do gears consist ofGears consist of toothed wheels fixed to shafts. The teeth interlock with each other, and as the first shaft (the driver shaft) rotates, the motion is transmitted to the second or driven shaft. The motion output at the driven shaft will be different from the motion input at the driver shaft - in place, speed, direction and other ways.
  36. 36how do you work out gear ratiohow do you work out gear ratio
  37. 37how do you calculate the output speedhow do you calculate the output speed
  38. 38what is this gear calledworm gearwhat is this gear called
  39. 39what gear is thisbevel gearswhat gear is this
  40. 40what is a pinion and a rackA pinion is a round cog and the rack is a flat bar with teeth
  41. 41how do a pinion and a rack workThe driver cog either moves along the rack, as in a rack and pinion (funicular) railway - or else the driver cog moves the rack, as in the steering system in cars. Rack and pinion changes rotary motion into linear motion - as shown in the diagram below.
  42. 42what are pulleys used forPulleys are used to change the speed, direction of rotation, or turning force or torque.
  43. 43what does a pulley system consist ofA pulley system consists of two pulley wheels each on a shaft, connected by a belt. This transmits rotary motion and force from the input, or driver shaft, to the output, or driven shaft
  44. 44how to work out the velocity ratio(pulley)how to work out the velocity ratio(pulley)
  45. 45how to work out the output speed (pulley)how to work out the output speed (pulley)
  46. 46what is torqueThe velocity ratio of a pulley system also determines the amount of turning force or torque transmitted from the driver pulley to the driven pulley
  47. 47how do you called the output torquehow do you called the output torque
  48. 48what are drive belts made ofDrive belts are usually made of synthetic fibres such as neoprene and polyurethane, with a V-shaped cross section
  49. 49how are u able to change direction using a pulley beltIt is possible to reverse the direction of the driven pulley by twisting the belt as it crosses from input to output
  50. 50why do pulley belts have an advantage over chainsPulley belts have the advantage over chains that they do not need lubrication (though unlike a chain, a belt can slip).
  51. 51what are the four basic types of motion in mechanical systemsThere are four basic types of motion in mechanical systems:
    Rotary motion is turning round in a circle, such as a wheel turning.
    Linear motion is moving in a straight line, such as on a paper trimmer.
    Reciprocating motion is moving backwards and forwards in a straight line, as in cutting with a saw.
    Oscillating motion is swinging from side to side, like a pendulum in a clock.
  52. 52what is a chain and sprocketA chain and sprocket changes rotary motion to linear motion - or vice versa. A wheel-and-axle, rack-and-pinion, rope-and-pulley, screw thread, or chain-and-sprocket could also be used for this.what is a chain and sprocket
  53. 53what is a cam and followerA cam-and-follower changes rotary motion to reciprocating motion. A crank, link and slider or rack-and-pinion could also be used for this.what is a cam and follower
  54. 54what is a peg and slotA peg-and-slot changes oscillating motion to rotary motion. A crank, link and slider could be used for this, and also to change rotary to oscillating motion.what is a peg and slot
  55. 55what is a crank link and slider4. A crank, link and slider will change rotary motion to oscillating / reciprocating motion.what is a crank link and slider
  56. 56what is a rack and pinionA rack-and-pinion changes rotary motion to reciprocating motion. A crank, link and slider could also be used for this. A cam-and-follower will change reciprocating to rotary motion.what is a rack and pinion
  57. 57—

Informationen

Beschreibung
Karteikarten am mechanisms, erstellt von ella stokes am 29/03/2017.
Erstellt von
ella stokes
Aufrufe
4
Bewertung

Feedback

Worum geht es?

Was sollen wir als Nächstes hinzufügen?