Quiz
CCNP switch
Erstelle ein kostenloses Konto, um dieses Quiz zu beenden
Speichere deinen Fortschritt und sieh dir dein Endergebnis an.
oder mit deiner E-Mail registrieren
Schon ein Konto? Anmelden
Fragen in diesem Quiz (60)
1Refer to the exhibit. The indicated configuration was established on the HSRP standby router RTB. However, the console message %IP-4-DUPADDR started appearing almost immediately on the RTB router. Given the output of the show standby brief command on RTA, what is the cause of the problem?
- AThe command standby pre-empt should only be applied on the active router.
- BThe subnet mask is missing from the standby ip 10.1.1.1 command.
- CThe group number 50 is missing in the Router RTB configuration commands.
- DThe priority number 150 is missing in the Router RTB configuration commands.
- EThe virtual IP address should be the same as the active router.
- FThe ports on the switch must be configured with the spanning-tree PortFast feature.
2Which statement correctly explains the process of mitigating ARP attacks on a switch where dynamic ARP inspection (DAI) has been configured?
- AAll intercepted packets that come from untrusted ports are dropped.
- BAll intercepted packets that come from trusted ports are sent to untrusted ports only.
- CThe intercepted packets are verified against the DHCP snooping binding table for valid IP-to-MAC bindings
- DFor all intercepted packets, an ARP request is sent to the DHCP server for IP-to-MAC address resolution
3Refer to the exhibit. What feature does an SNMP manager need to be able to set a parameter on ACSw1 ?

- AA manager who is using an SNMP string of K44p0uta
- BManager who is using an Inform Request MIB
- CA manager who is using host 192.168.0.5
- DA manager who is using authPriv
4Which statement is true concerning the core layer within the hierarchical design model?
- ARemote users are granted access to the network through the core.
- BRouting should be configured without traffic filtering, address translation, or other packet manipulation at the core.
- CThe core, which acts as the front door to a network, is designed to prevent unauthorized users from gaining entry.
- DThe core provides an optimized and reliable transport structure by using a combination of route summaries, distribution lists, and route maps.
5When a port security violation occurs on a switch port, the switch sends a syslog message but does not shutdown the port. What port security mode is in effect?
- ASticky
- BShutdown
- CRestrict
- Dprotect
6Which three steps are required to configure interfaces as routed ports on a multilayer Catalyst switch? (Choose three.)
- AEnable IP routing globally
- BAssign IP addresses to routed ports
- CConfigure SVI for each VLAN in the network
- DConfigure 802.1 Q encapsulation on routed ports
- EDisable Power over Ethernet (PoE) on the physical Layer 3 interfaces
- FDisable Layer 2 functionality on interfaces that will be configured as routed ports
7A bridging loop occurs in a network and disrupts user connectivity. What action should be taken by a network administrator to restore connectivity?
- ADisable ports that should be in the blocking state
- BDisable ports that should be in the forwarding state
- CDisable and re-enable all ports on the distribution switches
- DDisable all ports on the distribution switches and replace with new switches
8Which three actions can cause problems with a VTP implementation? (Choose three.)
- Ausing a non-trunk link to connect switches
- Busing non-Cisco switches
- Cconfiguring all switches to be in VTP server mode
- Dnot using any VTP passwords on any switches
- Eusing lowercase on one switch and uppercase on another switch for domain names
- Fhaving a VTP transparent switch in between a VTP server switch and a VTP client switch (all switches in the same VTP domain)
9Refer to the exhibit. What two conclusions can be made based on the output? (Choose two.)
- AInterfaces Fa0/1 through Fa0/6 are trunk ports.
- BSwitch DLS1 is not the root bridge for VLAN 1.
- CThe Cost column in the lower part of the exhibit is not the cumulative root path cost.
- DThe default spanning-tree timers have been adjusted.
- EThat Fa0/12 is displaying the alternate port role indicates that PVRST+ is enabled.
10Which QoS requirement should be taken into account when implementing VoIP in a campus environment?
- AThe QoS requirements should accommodate the best effort delivery for voice traffic.
- BThe QoS requirements should accommodate the bursty nature of voice traffic
- CThe QoS requirements should accommodate the intensive demand on bandwidth for voice traffic
- DThe QoS requirements should accommodate the smooth demand on bandwidth, low latency, and delay for voice traffic
11When troubleshooting GLBP in an environment with a VLAN that spans multiple access layer switches, a network engineer discovers that suboptimal paths are being used for upstream traffic. What is the recommended solution?
- AUse HSRP instead of GLBP
- BAdjust the GLBP timers
- CConfigure spanning tree so that the spanning-tree topology adjusts with the GLBP active virtual forwarder(AVF).
- DDisable GLBP preemption on all route processors
12Refer to the exhibit. What happens if interface gigabitEthernet 5/1 on SwitchA stops receiving UDLD packets?
- AUDLD stops trying to establish a connection with the neighbour.
- BUDLD changes the port state to err-disable.
- CUDLD changes the port to loop-inconsistent blocking state.
- DUDLD sends hello messages to its neighbour at a rate of one per second to attempt to recover the connection.
13How should a switch port be configured for a connection to a standalone wireless access point that provides multiple VLAN-separated SSIDs?
- Aas a trunk port
- Bas a routed port
- Cas an access port
- Das a switched virtual interface
14Which two procedures should be implemented and in place when deploying VoIP in a campus network?(Choose two.)
- AKeep voice and data traffic in the same VLAN and mark the traffic for high priority treatment.
- BCreate voice VLANs to keep voice traffic separate from other data to ensure special handling of the traffic.
- CConfigure traffic shaping QoS policy to guarantee minimum delay for the voice traffic
- DConfigure QoS policy to classify the voice traffic in the priority queue to guarantee reserved bandwidth allocation for the traffic
- EConfigure the Weighted Random Early Detection (WRED) congestion avoidance mechanism to guarantee that the voice traffic will be placed in the priority queue
15What are three possible misconfigurations or indicators of misconfigurations on a Layer 3 interface? (Choosethree.)
- Awrong IP address or subnet mask
- Bports in the wrong VLAN
- Cmismatch between SVI and VLAN numbering
- Ddisabled VTP pruning
- Edowned SVI
- FACL on wrong interface
16What type of queuing provides the best quality for voice applications?
- Acustom queuing
- BFIFO queuing
- Cpriority queuing
- Dweighted round robin (WRR) queuing
17Refer to the exhibit. What is the problem between the connection on Switch1 and Switch2?

- Anative VLAN mismatch
- BEncapsulation mismatch
- Cswitchport mode mismatch
- DVTP mismatch
- EDTP mismatch
- Fhardware failure
18Refer to the exhibit. The exhibit contains the configuration for a Cisco access device. How will someone dialing in be authenticated?
- Alocal username and password
- BTACACS+ server
- CRADIUS server and, if that fails, local username and password
- DTACACS+ server and, if that fails, local username and password
- ERADIUS server and, if that fails, TACACS+ server
19Which STP enhancement should be configured in the network to prevent a nondesignated port to transition to a forwarding state when a topology change occurs?

- ARoot guard should be implemented on the Layer 2 ports between the distribution switches.
- BPort Fast should be implemented on the uplink ports from the access switches to the distribution switches.
- CLoop guard should be implemented on the Layer 2 ports between DSW1 and DSW2 and on the uplink ports from the access switches to the distribution switches.
- DBPDU guard should be implemented on the Layer 2 ports between DSW1 and DSW2 and on the uplink ports from the access switches to the distribution switches.
20What are two actions a hacker may take in a VLAN hopping attack? (Choose two.)
- Areplying to ARP requests that are intended for other recipients
- Bsending malicious dynamic trunking protocol (DTP) frames
- Creplying to DHCP requests that are intended for a DHCP server
- Dsending a unicast flood of Ethernet frames with distinct source MAC addresses
- Esending frames with two 802.1Q headers
21Refer to the exhibit. Assuming that the switch is running Multiple Spanning Tree (MST), which conclusion can be made based on the output?
- ASpanning-tree load balancing is in effect.
- BAll VLANs are mapped to MST instance 2.
- CPVRST+ is still operating on switch DLS1.
- DPVST+ is still operating on switch DLS1.
- EMST will require fewer resources than PVST+ or PVRST+.
22A network administrator wants to implement inter-VLAN routing in the network. Which interfaces should be configured as routed ports?
- Aall interfaces on links 5 and 6
- Ball interfaces on links 1, 2, 3, and 4
- Call interfaces on links 1, 2, 3, 4, 5, and 6
- Dall interfaces between the distribution and the access switches
23Which three actions are taken when the commandswitchport host is entered on a switch port? (Choosethree.)
- ABPDU guard is enabled.
- BCisco Discovery Protocol (CDP) is disabled.
- CVLAN trunking protocol (VTP) is disabled.
- DPortFast is enabled
- ETrunking is disabled.
- FChannel group is disabled
24Which two statements are true about routed ports on a multilayer switch? (Choose two.)
- AA routed port behaves like a regular router interface and supports VLAN subinterfaces.
- BA routed port is a physical switch port with Layer 2 capability.
- CA routed port is not associated with a particular VLAN.
- DTo create a routed port requires removal of Layer 2 port functionality with the no switchport interface configuration command.
- EThe interface vlan global configuration command is used to create a routed port.
25Refer to the exhibit. Switches DSw1 and DSw2 are configured with the HSRP virtual IP address 10.10.10.1, and standby priority is set to 100. Assume both switches finish booting at the same time and HSRP is operating as expected. On the basis of this information, which three HSRP statements are true? (Choose three.)

- AApplying the standby 32 timers 10 30 command on the Gi0/2 interfaces of each switch would decrease the failover time.
- BIf the DSw1 and DSw2 switches have been configured to preempt, then DSw2 will be the active router.
- CIf the DSw1 switch is configured with the standby pre-empt command and DSw2 is not, then DSw1 will be the active router.
- DThe HSRP group number in this HSRP configuration is HSRP group number 50.
- EThe standby track command is useful for tracking interfaces that are not configured for HSRP.
- FWhen host A sends an ARP request for 10.10.10.1, Virtual Router replies with the MAC address of the active router
26What is the recommended maximum one-way jitter when implementing video over IP for real-time video applications?
- A1 ms
- B2 ms
- C5 ms
- D10 ms
27Refer to the exhibit. Based on the providedshow ip dhcp snooping command, which statement is true?

- AOnly port Fa0/24 can send and receive all DHCP messages.
- BPorts Fa0/1, Fa0/2, and Fa0/24 can send and receive all DHCP messages.
- COnly ports Fa0/1 and Fa0/2 can send and receive all DHCP messages.
- DPorts Fa0/1, Fa0/2, and Fa0/24 can send and receive only DHCP requests
28Which two items in the TCAM table are referenced in the process of forwarding a packet? (Choose two.)
- AVLAN ID
- BACL information
- Cdestination MAC address
- DQoS information
- Esource MAC address
- Fhash key
29Catalyst Catalyst 6500 switches support which three Supervisor Engine redundancy features? (Choose three.)
- ARoute Processor Redundancy+ (RPR+)
- Bdistributed CEF (dCEF)
- CStateful Switchover (SSO)
- DResilient Packet Ring (RPR)
- ENonstop Forwarding (NSF)
- FPer Line Card Traffic Policing
30Which two statements are true about the default operation of STP in a Layer 2 switched environment that has redundant connections between switches? (Choose two.)
- AThe root switch is the switch with the highest speed ports
- BDecisions on which port to block when two ports have equal cost depend on the port priority and index.
- CAll trunking ports are designated and not blocked
- DRoot switches have all ports set as root ports
- ENonroot switches each have only one root port
31Which benefit is provided by centralizing servers in a data center server farm?
- AIt keeps client-to-server traffic local to a single subnet.
- BServers that are located in a data center require less bandwidth.
- CIt is easier to filter and prioritize traffic to and from the data center.
- DServer farms are not subject to denial of service attacks.
32Refer to the exhibit. What restriction will be presented in a campus enterprise network that is designed with four large distribution building blocks?

- AThe implementation of link aggregation will be limited.
- BThe implementation of IGP routing protocols will be limited
- CThe implementation of EtherChannels on redundant links will exceed the bandwidth
- DThe implementation of scalability that is required during future growth will be limited
33Which three issues can cause devices to become disconnected across a trunk link? (Choose three.)
- Anative VLAN mismatch
- Bunassigned management VLAN
- CLayer 2 interface mode incompatibilities
- Dmissing default VLAN
- Emismatched trunk encapsulations
- FPAgP not enabled
34Refer to the exhibit. What additional configuration is required in order for users in VLAN 10 to communicate with the users in VLAN 20?

- AConfigure interface Fa0/1 on SW1 as a trunk.
- BRemove the subinterfaces on R1 and configure interface Fa0/0 as a trunk.
- CConfigure interfaces Fa0/2 and Fa0/3 on SW1 as trunk links.
- DConfigure VLAN 100 as a data VLAN and VLAN 1 as the native VLAN.
35Refer to the exhibit. Given that interface Fa3/42 is an active trunk port, what two conclusions can be made based on the displayed output? (Choose two.)
- ARoot guard is not enabled on interface Fa3/42

- BInterface Fa3/42 will not pass data traffic if it detects that it is part of a spanning-tree loop caused by unidirectional link failure
- CUDLD cannot be configured on interface Fa3/42
- DIf a spanning-tree loop is detected on VLAN 1, data traffic will be blocked for all VLANs on interface Fa3/42
- EThe difference in BPDUs sent and received indicates a loop caused by unidirectional link failure has been detected
- ARoot guard is not enabled on interface Fa3/42
36Which architecture enables enterprises to offer important network services, such as security, new communication services, and improved application performance to every office, regardless of its size or proximity to headquarters?
- ACisco Enterprise Campus Architecture
- BCisco Enterprise Data Center Architecture
- CCisco Enterprise Branch Architecture
- DCisco Enterprise Teleworker Architecture
37Which three parameters must be configured in order to enable SSH? (Choose three.)
- ARetries
- BHostname
- CTimeouts
- Ddomain name
- EKeys
- Frouting protocol
38The TCAM defines three different match options that correlate to which three specific match regions? (Choose three.)
- Abifurcated match
- Blongest match
- Csecond match
- Dexact match
- Efirst match
- Fthird match
39Which two types of attacks can be mitigated by port security? (Choose two.)
- ADictionary
- Bdenial of service (DoS)
- CReplay
- DMAC-address flooding
- Epassword
40What is a characteristic of a standalone WLAN solution?
- Ahas no centralized monitoring
- Bhas no centralized management
- Chas no centralized operational control
- Dhas no centralized access authentication
41Refer to the exhibit. What configuration will be required on the DSW switch in order to perform inter-VLAN routing for all VLANs that are configured on the access switches?

- AConfigure the routing protocol
- BConfigure SVI for each VLAN in the network
- CConfigure the links between DSW and the access switches as access links
- DConfigure as routed ports the DSW interfaces that face the access switches
42How do FlexLink and STP operate together?
- AIf an active STP port is blocked, the active FlexLink port will take over
- BBoth the active STP port and active FlexLink port can forward traffic simultaneously
- CBoth the active STP port and active FlexLink port can forward traffic simultaneously but only for different VLANs
- DSTP can be active in the distribution layer, but is unaware of any FlexLink updates in the access layer
43Refer to the exhibit. What two effects will occur when a fourth distribution module is included in the campus enterprise network that is depicted in the exhibit? (Choose two.)

- AThe inclusion of the fourth module will increase the routing complexity.
- BIt will limit the traffic flow in the network
- CIt will provide scalability for future growth
- DIt will impact the security of the traffic between the distribution switches
- EIt will increase the number of additional links that are required to provide redundant connectivity
44Refer to the exhibit. What statement is true about the way HSRP is configured?

- ASwitch DLS1 is the standby router for VLANs 1,10, and 20.
- BSwitch DLS2 is the standby router for VLANs 30 and 40.
- CIssuing the show standby command on switch DSL1 will reveal that the HSRP state for VLAN 10 is standby.
- DIssuing the show standby command on switch DSL2 will reveal that the HSRP state for VLAN 30 is standby
- EBy setting different priorities on different VLANs, a type of load balancing is occurring
- FIf the Ethernet cables between switch DLS2 and switch ALS1 were severed, Payroll Host would not be able to reach SQL Server
45When should a proactive management be performed within the stages of the Cisco Lifecycle Services?
- Aprepare phase
- Bplan phase
- Cdesign phase
- Dimplement phase
- Eoperate phase
- Foptimize phase
46Refer to the exhibit. What is the result of the displayed configuration on switches ASW1 and ASW2?

- ABPDU guard puts an interface that is configured for STP PortFast in the err-disable state upon receipt of a BPDU.
- BBPDU guard overrides the PortFast configuration and reverts to the default spanning tree configuration on the access ports.
- CBPDU guard forces the uplink ports on ASW1 and ASW2 to become designated ports to prevent DSW2 from becoming a root switch.
- DBPDU guard places the uplink ports on a ASW1 and ASW2 into the STP loop-inconsistent blocking state when the ports stop receiving BPDUs.
47Which multilayer switching forwarding method does Cisco Express Forwarding (CEF) use?
- Aroute caching
- Bprocess switching
- Csilicon switching
- Dtopology-based switching
48Refer to the exhibit. A network administrator wants to verify the proper operations of the packet load sharing between a group of redundant routers that are configured with GLBP. On the basis of the provided output, which router is the Active Virtual Forwarder (AVF) for Host2?

- Athe router with an IP address of 10.1.1.1
- Bthe router with an IP address of 10.1.1.2
- Cthe router with the virtual IP address of 10.1.1.254
- Dthe router with the IP address 10.1.1.1 and the router with the IP address 10.1.1.2
49What is required for SLA to capture one-way delays?
- Atwo IP SLA responders
- Ba Round Trip Timer value
- CNetwork Time Protocol (NTP)
- DIP SLA source using TCP port 2020
50What is the most common method of configuring inter-VLAN routing on a Layer 3 switch?
- AConfigure the switch physical interface so that the router will have an interface in each VLAN.
- BFor each VLAN, configure trunking between the router and the switch.
- CConfigure a routing protocol on the Layer 3 switch to include each interface
- DConfigure switch virtual interfaces. The result is that the router will have a virtual interface in each VLAN.
51What is the purpose of the debug condition standby vlan vlan-id group-number command in troubleshooting HSRP?
- Aredirect the debug standby output for the referenced HSRP group to a syslog server on the specified VLAN
- Bblock the debug standby output for the referenced VLAN and HSRP group
- CDisplay debug standby output only for HSRP traffic that is received by HSRP peers in the specified VLAN and group
- DDisplay debug standby output only for HSRP traffic that is sent to HSRP peers in the specified VLAN and group
- Elimit the output of the debug standby command to the specific VLAN interface and HSRP group
52What device can be used to support Power over Ethernet (PoE) to power the access points?
- Aa host computer
- Ban IP phone
- Can Ethernet switch
- Da lightweight access point
53Which three statements about RSTP edge ports are true? (Choose three.)
- AEdge ports function similarly to UplinkFast ports.
- BEdge ports should never connect to another switch
- CIf an edge port receives a BPDU, it becomes a normal spanning-tree port
- DEdge ports immediately transition to learning mode and then forwarding mode when enabled
- EEdge ports never generate topology change notifications (TCNs) when the port transitions to a disabled or enabled status
- FEdge ports can have another switch connected to them as long as the link is operating in full duplex
54What are two benefits of local VLANs in the Enterprise Campus Network? (Choose two.)
- Awide coverage because of the fact that a VLAN can be geographically dispersed throughout the network
- Bease of management because local VLANs are typically confined to the building access submodule
- Chigh availability because redundant paths exist at all infrastructure levels
- Dbroad expansion domain because the number of devices on each VLAN can easily be added to
- EIP address conservation because address blocks can be allocated to VLANs
55Which phase of the Cisco Lifecycle Services approach includes building a network according to the design and verifying that it performs according to specifications?
- Aprepare phase
- Bplan phase
- Cdesign phase
- Dimplement phase
- EOperate phase
- FOptimize phase
56Refer to the exhibit. The link between switch SW1 and SW2 is manually configured as full duplex on SW2 and with half duplex on SW1. How could this impact the STP operations?

- ASwitch SW2 can move port Fa0/3 into a forwarding state, thereby creating a Layer 2 loop
- BSwitch SW1 shuts down the Fa0/1 port and thus reinforces a new spanning-tree calculation.
- CSwitch SW2 negotiates the Fa0/1 port on SW1 to be in full-duplex mode which keeps SW1 as the rootbridge for the spanning tree.
- DSwitch SW1 negotiates the Fa0/2 port on SW2 to be in half-duplex mode and thus forces SW2 to become the root bridge for the spanning tree.
57What three features are provided by IEEE 802.1Q trunking? (Choose three.)
- ASecurity
- BResilience
- CQoS support
- Dmultivendor support
- Erelatively small frame overhead
- Fmulticast support
58How many physical links can comprise a single PAgP EtherChannel on a Catalyst 3560 switch? (Choose three.)
- A2
- B5
- C8
- D10
- E12
- F13
- G16
59What is the most fundamental form of high availability when using Catalyst modular switches?
- ASpanning Tree Protocol
- Brouting protocol
- CFirst Hop Redundancy Protocol (FHRP)
- DSupervisor Engine redundancy
- Eredundant switching modules
60What is the recommended maximum one-way latency when implementing video over IP for real-time video applications?
- ALatency is not a factor for a smooth video over IP implementation.
- BLatency should be defined for voice traffic only (not for video).
- CThe recommended maximum one-way latency should not be more than 150 ms.
- DWhen mixed video and voice packets are included in the video stream, the latency should be 300 ms.
Informationen
- Beschreibung
- Quiz am CCNP switch, erstellt von amandeep.purewal am 16/12/2015.
- Autor
- amandeep.purewal
- Sprache
- English
- Aufrufe
- 88
- Bewertung
- Noch keine Bewertungen Bewerte dieses Quiz