Ayúdanos a dar forma a GoConqr. ¿Qué deberíamos añadir?

Test

CCNP switch

amandeep.purewal 60 preguntas

Hacer el test

Preguntas del test (60)

  1. 1Refer to the exhibit. The indicated configuration was established on the HSRP standby router RTB. However, the console message %IP-4-DUPADDR started appearing almost immediately on the RTB router. Given the output of the show standby brief command on RTA, what is the cause of the problem?
    1. AThe command standby pre-empt should only be applied on the active router.
    2. BThe subnet mask is missing from the standby ip 10.1.1.1 command.
    3. CThe group number 50 is missing in the Router RTB configuration commands.
    4. DThe priority number 150 is missing in the Router RTB configuration commands.
    5. EThe virtual IP address should be the same as the active router.
    6. FThe ports on the switch must be configured with the spanning-tree PortFast feature.
  2. 2Which statement correctly explains the process of mitigating ARP attacks on a switch where dynamic ARP inspection (DAI) has been configured?
    1. AAll intercepted packets that come from untrusted ports are dropped.
    2. BAll intercepted packets that come from trusted ports are sent to untrusted ports only.
    3. CThe intercepted packets are verified against the DHCP snooping binding table for valid IP-to-MAC bindings
    4. DFor all intercepted packets, an ARP request is sent to the DHCP server for IP-to-MAC address resolution
  3. 3Refer to the exhibit. What feature does an SNMP manager need to be able to set a parameter on ACSw1 ?Imagen de la pregunta 3
    1. AA manager who is using an SNMP string of K44p0uta
    2. BManager who is using an Inform Request MIB
    3. CA manager who is using host 192.168.0.5
    4. DA manager who is using authPriv
  4. 4Which statement is true concerning the core layer within the hierarchical design model?
    1. ARemote users are granted access to the network through the core.
    2. BRouting should be configured without traffic filtering, address translation, or other packet manipulation at the core.
    3. CThe core, which acts as the front door to a network, is designed to prevent unauthorized users from gaining entry.
    4. DThe core provides an optimized and reliable transport structure by using a combination of route summaries, distribution lists, and route maps.
  5. 5When a port security violation occurs on a switch port, the switch sends a syslog message but does not shutdown the port. What port security mode is in effect?
    1. ASticky
    2. BShutdown
    3. CRestrict
    4. Dprotect
  6. 6Which three steps are required to configure interfaces as routed ports on a multilayer Catalyst switch? (Choose three.)
    1. AEnable IP routing globally
    2. BAssign IP addresses to routed ports
    3. CConfigure SVI for each VLAN in the network
    4. DConfigure 802.1 Q encapsulation on routed ports
    5. EDisable Power over Ethernet (PoE) on the physical Layer 3 interfaces
    6. FDisable Layer 2 functionality on interfaces that will be configured as routed ports
  7. 7A bridging loop occurs in a network and disrupts user connectivity. What action should be taken by a network administrator to restore connectivity?
    1. ADisable ports that should be in the blocking state
    2. BDisable ports that should be in the forwarding state
    3. CDisable and re-enable all ports on the distribution switches
    4. DDisable all ports on the distribution switches and replace with new switches
  8. 8Which three actions can cause problems with a VTP implementation? (Choose three.)
    1. Ausing a non-trunk link to connect switches
    2. Busing non-Cisco switches
    3. Cconfiguring all switches to be in VTP server mode
    4. Dnot using any VTP passwords on any switches
    5. Eusing lowercase on one switch and uppercase on another switch for domain names
    6. Fhaving a VTP transparent switch in between a VTP server switch and a VTP client switch (all switches in the same VTP domain)
  9. 9Refer to the exhibit. What two conclusions can be made based on the output? (Choose two.)
    1. AInterfaces Fa0/1 through Fa0/6 are trunk ports.
    2. BSwitch DLS1 is not the root bridge for VLAN 1.
    3. CThe Cost column in the lower part of the exhibit is not the cumulative root path cost.
    4. DThe default spanning-tree timers have been adjusted.
    5. EThat Fa0/12 is displaying the alternate port role indicates that PVRST+ is enabled.
  10. 10Which QoS requirement should be taken into account when implementing VoIP in a campus environment?
    1. AThe QoS requirements should accommodate the best effort delivery for voice traffic.
    2. BThe QoS requirements should accommodate the bursty nature of voice traffic
    3. CThe QoS requirements should accommodate the intensive demand on bandwidth for voice traffic
    4. DThe QoS requirements should accommodate the smooth demand on bandwidth, low latency, and delay for voice traffic

Información

Descripción
Test sobre CCNP switch, creado por amandeep.purewal el 16/12/2015.
Idioma
English
Visitas
88
Valoración
Aún sin valoraciones
Valora este test
Valora este test

Escríbenos

¿Sobre qué es tu mensaje?

¿Qué deberíamos añadir?