Gestalte GoConqr mit. Was sollen wir als Nächstes hinzufügen?

Quiz

CCNA – EtherChannel

jonathan rozo 5 Fragen

Quiz starten

Fragen in diesem Quiz (5)

  1. 1QUESTION NO: 286
    Refer to the exhibit.
    A network administrator is configuring an EtherChannel between SW1 and SW2. The SW1 configuration is shown. What is the correct configuration for SW2?

    Bild zu Frage 1
    1. Ainterface FastEthernet 0/1
      channel-group 1 mode active
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 1 mode active
      switchport trunk encapsulation dot1q
      switchport mode trunk
    2. Binterface FastEthernet 0/1
      channel-group 2 mode auto
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 2 mode auto
      switchport trunk encapsulation dot1q
      switchport mode trunk
    3. Cinterface FastEthernet 0/1
      channel-group 1 mode desirable
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 1 mode desirable
      switchport trunk encapsulation dot1q
      switchport mode trunk
    4. Dinterface FastEthernet 0/1
      channel-group 1 mode passive
      switchport trunk encapsulation dot1q
      switchport mode trunk
      interface FastEthernet 0/2
      channel-group 1 mode passive
      switchport trunk encapsulation dot1q
      switchport mode trunk
  2. 2QUESTION NO: 292
    Refer to the exhibit.
    If the devices produced the given output, what is the cause of the EtherChannel problem?

    Bild zu Frage 2
    1. ASW1's Fa0/1 interface is administratively shut down.
    2. BThere is an encapsulation mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
    3. CThere is an MTU mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
    4. DThere is a speed mismatch between SW1's Fa0/1 and SW2's Fa0/1 interfaces.
  3. 3QUESTION NO: 294
    A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?

    1. Athe port-channel 1 interface
    2. Bthe highest number member interface
    3. Call member interfaces
    4. Dthe lowest number member interface
  4. 4QUESTION NO: 288
    What parameter can be different on ports within an EtherChannel?

    1. Aspeed
    2. BDTP negotiation settings
    3. Ctrunk encapsulation
    4. Dduplex
  5. 5QUESTION NO: 290
    Refer to the exhibit.


    What set of commands was configured on interface Fa0/3 to produce the given output?

    Bild zu Frage 5
    1. Ainterface FastEthernet 0/3
      channel-group 1 mode desirable
      switchport trunk encapsulation dot1q
      switchport mode trunk
    2. Binterface FastEthernet 0/3
      channel-group 2 mode passive
      switchport trunk encapsulation dot1q
      switchport mode trunk
    3. Cinterface FastEthernet 0/3
      channel-group 2 mode active
      switchport trunk encapsulation dot1q
      switchport mode trunk
    4. Dinterface FastEthernet 0/3
      channel-group 2 mode on
      switchport trunk encapsulation dot1q
      switchport mode trunk

Informationen

Beschreibung
Quiz am CCNA – EtherChannel , erstellt von jonathan rozo am 13/06/2016.
Sprache
Español
Aufrufe
3
Bewertung
Noch keine Bewertungen
Bewerte dieses Quiz
Bewerte dieses Quiz

Mehr zu EtherChannel and Link Aggregation

Feedback

Worum geht es?

Was sollen wir als Nächstes hinzufügen?