Quiz
Física 2
Erstelle ein kostenloses Konto, um dieses Quiz zu beenden
Speichere deinen Fortschritt und sieh dir dein Endergebnis an.
oder mit deiner E-Mail registrieren
Schon ein Konto? Anmelden
Fragen in diesem Quiz (200)
1The source voltage in the circuit shown is.
- A200V.
- B50V.
- C150V.
2Referring to the drawing, if the volts dropped across the 20 ohm resistor is 10 volts, the resistance of R1 is.
- A2 ohms.
- B16 ohms.
- C20 ohms.
3The current in the circuit shown is.
- A5 mA.
- B0.2 A.
- C5 A
4In the following circuit, the input at P is 4 amps and at Q is 5 amps. What is the voltage across the 6 ohm resistor?.
- A54V.
- B6V.
- C1.5V.
5The unknown current in the network below is.
- A22A.
- B3A.
- C47A
6In a balanced Wheatstone bridge, across the centre of the bridge there is.
- Acurrent and voltage at maximum.
- Bno current flow.
- Cno voltage present at either end
7A 24V battery has an internal resistance of 1 ohm. When connected to a load, 12 amps flows. The value of the load is.
- A12 ohms.
- B1/2 ohm.
- C1 ohm
8A parallel circuit with any number of 2 terminal connections.
- Athe individual voltage drops is equal to the emf.
- Bhas the same current throughout.
- Cthe resistance is dependent on current
9The diagram shows a 200V long shunt generator. What is the voltage across the series resistor.
- A10V.
- B6V.
- C30V.
10To find the internal resistance of a battery in a circuit of known current.
- Ause the formula R = V * I.
- Bfind the lost volts of the circuit.
- Cfind the emf of the circuit.
11For the diagram shown find the voltage at point B.
- A7V.
- B26V.
- C10V.
12In a series circuit with 3 resistors, the current is.
- Alower than the smallest.
- Bthe total of all 3 using ohms law to find the current.
- Ceven in all 3.
13What is the voltage dropped across resistor 'A'?.
- A2 V.
- B20 V.
- C10 V.
14What is the current through resistor C?.
- A4.5A.
- B18A.
- C9A.
15Which is not thermally operated?.
- AA limiting resistor.
- BA current limiter.
- CA fuse
16In a Desynn indicator system, the rotor is.
- Aan electromagnet.
- Ba permanent magnet.
- Can AC magnet.
17A load that is subject to a potential difference with a current running through it will.
- Ahave a magnetic field around it with the magnitude and direction of the field determined by the corkscrew rule.
- Bdissipate power in the form of heat.
- Cwill move in a direction shown by the right hand rule.
18The resistance of a material is.
- Aindependent of the material type.
- Bthe same as its conductance.
- Cthe reciprocal of its conductance
19Resistance is measured using what unit of temperature?.
- AAbsolute.
- BCentigrade.
- CFahrenheit.
20A resistor has 4 bands on it coloured blue, yellow, yellow, gold. It’s value is.
- A640 kΩ ± 5%.
- B6.4 mΩ ± 10%.
- C64 kΩ ± 5%.
21The electron flow through a conductor will be decreased the most if the cross sectional area.
- Ais decreased and the length is increased.
- Band the length are both decreased.
- Cand the length are both increased
22Small resistors too small or mis-shapen for the application of colour are marked instead using.
- Aan abbreviated resistance value.
- Ba letter code.
- Ca dot code
23Total resistance in a parallel resistor circuit, of R1 and R2 is.
- ART = 1/R1 + 1/R2.
- B1/RT = (R1 * R2) ÷ (R1 + R2).
- C1/RT = 1/R1 + 1/R2.
24If the resistance of a resistor which is in series with two other resistors is doubled.
- Athe current in that resistance is doubled.
- Bthe volts drop across that resistor increases.
- Cthe current in that resistance is halved.
25The total resistance of the circuit shown is.
- A3 Ohms.
- B1.33 Ohms.
- C12 Ohms
26Potentiometers are used as a.
- Avariable voltage source.
- Bvariable resistor.
- Cvariable current source.
27 In a Wheatstone Bridge, the ammeter reads zero, and the variable resistor is adjusted to 5 ohms. Resistor P has a value of 10 ohms and Q has a value of 100 ohms. What is the value of the unknown resistor?.
- A5 ohms.
- B0.5 ohms.
- C50 ohms
28In general, increasing the cross sectional area of an electrical cable.
- Aincreases its resistance.
- Benables it to carry more voltage.
- Cenables it to carry more current.
29Six resistors each of 6 ohms would be.
- A1 ohm in series.
- B1 ohm in parallel.
- C36 ohms in parallel.
30A potentiometer varies.
- Aresistance.
- Bcurrent.
- Cvoltage
31The formula for resistance in series is.
- ART = R1 + R2 + R3 .....Rn.
- BRT = R1 * R2 * R3 .....Rn.
- C1/RT = 1/( R1 * R2 * R3 .....Rn).
32What is the combined value of resistances of 4 ohm and 6 ohm connected in parallel?.
- A0.24 ohm.
- B2.4 ohm.
- C24 ohm.
33If a number of resistors are connected in parallel, the total resistance is.
- Asmaller than the lowest.
- Bthe same as the lowest.
- Cgreater than the lowest.
34The resistance to electrical flow in a wire depends on.
- Athe diameter, length, material of wire and temperature.
- Bthe material only - copper or aluminium.
- Cthe length and material of the wire only.
35When resistors are in parallel the total current is equal to.
- Athe current through one resistor.
- Bthe sum of the currents.
- Cthe reciprocal of all the currents.
36Which of these will cause the resistance of a conductor to decrease?.
- ADecrease the length or the cross-sectional area.
- BIncrease the length or decrease the cross-sectional area.
- CDecrease the length or increase the cross-sectional area
37 If 2 resistors, one red, yellow, black, gold and the other violet, blue, black, silver were replaced by a single resistor. Ignoring tolerance, what would the colour coding be?.
- ABrown, black, brown.
- BBlack, brown, black.
- CBrown, black, black.
38A 47 kilohm resistor has the following colour code:.
- AYellow, Violet, Orange.
- BRed, Orange, Yellow.
- COrange, Violet, Red.
39The bridge circuit shown will be balanced when the value of the unknown resistor R is.
- A2 ohms.
- B18 ohms.
- C14 ohms.
40A 300 ohm resistor would have a colour code of.
- Aorange, brown, black.
- Borange, orange, brown.
- Corange, black brown
41In this circuit, Rx is equal to.
- AR2 * R4 ÷ R3.
- BR3 * R4 ÷ R2.
- CR3 * R2 ÷ R4.
42In a parallel circuit containing resistors.
- Athe sum of the voltage drops equals applied voltage.
- Bthe voltage is the same in all parts of the circuit.
- Cresistance is determined by value of current flow.
43Five different value resistors all have the same voltage dropped across them. How are the resistors connected?.
- AIn Series/Parallel.
- BIn Series.
- CIn Parallel
44Conductance of a circuit is 2 milliMhos. What is its resistance?.
- A5000 Ohms.
- B500 Ohms.
- C5 Megohms.
45When light hits a photodiode, its resistance.
- Astays the same.
- Bincreases.
- Cdecreases
46 A 2 Megohm resistor can be written.
- A2M0F.
- B20MF.
- CM20F
47In a Wheatstone bridge at balance the galvanometer reads zero.
- Aamps.
- Bohms.
- Cvolts.
48The unit for resistivity is the.
- Aohms/square meter.
- Bohms/meter.
- Cohm.meter.
49A 47 Kilohm resistor with a 10% tolerance has the following colour code:.
- AYellow, Violet, Orange, Silver.
- BOrange, Violet, Red, Gold.
- CRed, Orange, Yellow, Silver.
50The total resistance in a circuit is greater than the least resistor. This is true for a.
- Aseries and parallel circuit.
- Bseries circuit only.
- Cparallel circuit only.
51The unknown resistance R in the Wheatstone bridge shown is.
- A4 ohms.
- B16 ohms.
- C1 ohm
52This is a symbol for.
- Aa visual display rectifier.
- Ba variable differential resistor.
- Ca voltage dependant resistor
53A potentiometer has which of the following properties?.
- AWire wound.
- B3 terminals.
- CPreset values
54An increase in operating temperature in most electrical devices carrying current results in.
- Aa decrease in resistance and an increase in current.
- Bno effect on the resistance and current.
- Can increase in resistance and a decrease in current
55Copper is an inferior conductor to aluminium when comparing.
- ACSA with CSA.
- Bweight for weight.
- Cload for load.
56What happens to the resistance of a copper conductor when the temperature increases?.
- AIt decreases.
- BIt increases.
- CIt remains the same.
57Carbon has a.
- Atemperature coefficient of zero.
- Bpositive temperature coefficient.
- Cnegative temperature coefficient.
58The 5th coloured band on a resistor represents the.
- Areliability or temperature coefficient.
- Btolerance.
- Cmultiplier.
59If the temperature of a pure metal is reduced to absolute zero, its resistance will be.
- Aunaffected.
- Bpractically zero.
- Cinfinity.
60What is represented by this diagram?.
- AThermistor.
- BRheostat.
- CPotentiometer.
61If a resistor is too small or misshapen to fit the colour code bands, how else is it's value indicated?.
- ADots.
- BNumber code.
- CLetter code.
62This is a diagram of a.
- ALight Dependant Resistor.
- BLaser Diode Rectifier.
- CLogarithmic Differential Resistor.
63This is a diagram of a.
- AVariable Voltage source.
- BVariable Current source.
- CVariable Resistor.
64Resistors required to carry a comparatively high current and dissipate high power are usually of.
- AWire wound metal type.
- BCarbon compound type.
- CWire wound ceramic type.
65A thyristor.
- Aif energized on, will switch on a circuit.
- Bhas a positive temperature coefficient.
- Cif energized on, will switch off a circuit
66The temperature of a pure metal can greatly affect the resistance of it. What temperature scale is used?.
- AAbsolute.
- BCentigrade.
- CFahrenheit.
67A 10 V battery supplies a resistive load of 10 ohms for 1 minute. What is the power supplied?.
- A100 W.
- B10 VA.
- C10 W
68A resistor dissipates 80 Watts. If it runs for 4 hours 15 minutes, how much energy is dissipated in total?.
- A20.4 kJ.
- B1.224 MJ.
- C191.25 J.
69The earth lead of a 24 V equipment is 0.5 ohm resistance and carries 80 A. How much power does it dissipate?.
- A1.92 kW.
- B1.152 kW.
- C3.2 kW.
70What is the power dissipated in a 500 ohm resistor with a 3A flow?.
- A4.5 kW.
- B1.5 kW.
- C750 kW.
71A DC circuit containing a total resistance of 100 ohms has a current flow of 250 mA. The power dissipated in the circuit is.
- A0.4 watts.
- B5 watts.
- C6.25 watts
72Power is the rate of doing work. It is measured in.
- Ajoules/second.
- Bjoules * seconds.
- Cwatts/second
73The power in a circuit when voltage and resistance is given can be found by.
- AV*R.
- BV*V*R.
- CV*V / R
74A 500 ohm resistor carries a 3 amp current. What is the power dissipated?.
- A500 W.
- B5 kW.
- C4.5 kW.
75A 3 ohm resistor dissipates 27 Watts. How much current flows through it?.
- A9 A.
- B0.15 A.
- C3 A.
76A 48-volt source is required to furnish 192 watts to a parallel circuit consisting of three resistors of equal value. What is the value of each resistor?.
- A4 ohm.
- B36 ohm.
- C12 ohm
77A piece of equipment is rated at 750 watts and the applied voltage is 30 volts. The value of the protection fuse should be.
- A20 amps.
- B15 amps.
- C30 amps.
78How much power must a 24-volt generator furnish to a system which contains the following series loads? 5 ohm, 3 ohm and 12 ohm.
- A402 watts.
- B28.8 watts.
- C450 watts.
79A direct current of 12 milliamperes flows through a circuit which has a resistance of 1000 ohms. The power dissipated by the circuit is.
- A144 milliwatts.
- B12 watts.
- C12 milliwatts.
80In the circuit shown, the power developed across the 10 kilo ohm resistor is.
- A250 mW.
- B250 W.
- C50 mW.
81A single phase circuit has an input voltage of 100V. The current is 10A and the circuit has a power factor of 0.5. The true power is.
- A50W.
- B1000W.
- C500W.
82Power in a DC circuit is found by.
- Amultiplying the voltage by itself and dividing by the current.
- Bmultiplying current by resistance.
- Cmultiplying the resistance by the current squared
83If the energy supplied to a circuit for 4hrs 15 minutes at 800 j/sec what would be the energy consumed?.
- A3400 KW Hrs.
- B3.4 KW Hrs.
- C340 KW Hrs.
84A heater which consumes 800 Kilojoules/sec is on for 4hrs 15min. The energy consumed is.
- A340 kWh.
- B3.4 kWh.
- C3400 kWh.
85A voltage of 250V causes a current of 30mA. What is the wattage?.
- A7.5W.
- B7500W.
- C0.225W
86Which requires the most electrical power during operation?.
- AA 12-volt motor requiring 8 amperes.
- BFour 30-watt lamps in a 12-volt parallel circuit.
- CTwo lights requiring 3 amperes each in a 24volt parallel system
87The power dissipated in a circuit with a known potential difference and resistance is calculated by.
- Amultiplying the square of the potential difference by the resistance.
- Bdividing the square of the potential difference by the resistance.
- Cfinding the current and multiplying the answer by the resistance
88The power expended in a given circuit is.
- Ainversely proportional to cube-root of the current.
- Bproportional to the square-root of the voltage.
- Cproportional to the square of the voltage.
89A capacitor is fully charged after 25 seconds to a battery voltage of 20 Volts. The battery is replaced with a short circuit. What will be the voltage across the capacitor after one time constant?.
- A0 volts.
- B7.36 volts.
- C12.64 volts.
90The voltage rating of a capacitor is.
- Athe max voltage that can be constantly applied.
- Bthe min voltage required to charge.
- Cthe normal operating voltage.
91The relative permittivity of a capacitor is.
- Athe permittivity of the dielectric.
- Bthe relative permittivity of the dielectric in relation to a vacuum.
- Cthe permittivity of dielectric in relation to dry air.
92When checking a capacitor with an ohmmeter, if the reading shows charging but the final reading is less than normal then the possible fault is a.
- Aleaking dielectric capacitor.
- Bshort circuit dielectric.
- Copen circuit dielectric.
93Three capacitors 10 microfarads, 10 nanofarads and 10 millifarads are connected in parallel. What is the total capacitance?.
- A10.01001 millifarads.
- B111 millifarads.
- C1.001001 millifarads.
94If a 1milliFarad capacitor has a potential difference across it of 5V, what is the energy stored?.
- A12.5 Joules.
- B12.5 milliJoules.
- C25 mJoules.
95A capacitor with double the area and double the dielectric thickness will have.
- Adouble the capacitance.
- Bthe same capacitance.
- Chalf the capacitance.
96 An electrolytic capacitor is used where.
- Aminimum losses are essential.
- Bthere is a polarized input.
- Chigh frequency AC is used
97What must you do to make a 3 F capacitor circuit into a 2 F circuit?.
- APut a 2 F capacitor in parallel.
- BPut a 6 F capacitor in series.
- CPut a 1 F capacitor in series.
98The time required to fully charge a 1 µ(micro)F capacitor in series with a 100k ohm resistor is.
- A100 seconds.
- B100 milliseconds.
- C500 milliseconds.
99A 50 μ(micro) Farad capacitor is fed with a current of 25 milliAmpere. How long will it take to charge it to 100Volts?.
- A1 second.
- B0.2 seconds.
- C12 minutes.
100In a circuit C = 25 microfarads and the current flow is 40 microamps for 4 seconds. What is the voltage?.
- A6.4Volts.
- B3.2Volts.
- C12.8Volts
101Three 12 µ(micro)F capacitors are in series. The total capacitance is.
- A12 µ(micro)F.
- B4 µ(micro)F.
- C36 µ(micro)F.
102The time constant of a capacitor is the time.
- Athe current to reach 63.2% of maximum.
- Bfor the emf to reach 63.2% of maximum.
- Cto reach maximum current.
103The amount of electricity a capacitor can store is directly proportional to the.
- Aplate area and inversely proportional to the distance between the plates.
- Bdistance between the plates and inversely proportional to the plate area.
- Cplate area and is not affected by the distance between the plates.
104The capacitance of a capacitor is dependant upon.
- Athe rate of change of current in the circuit.
- Bthe type of material separating the plates.
- Cthe charge on it.
105When different rated capacitors are connected in parallel in a circuit, the total capacitance is.
- Aless than the capacitance of the lowest rated capacitor.
- Bequal to the capacitance of the highest rated capacitor.
- Cequal to the sum of all the capacitances.
106One Picofarad is.
- A1 * 1012 farad.
- B1 * 10-6 farad.
- C1 * 10-12 farad.
107The switch on a DC circuit containing a fully charged capacitor is opened. The voltage across the capacitor.
- Adrops immediately to zero.
- Bstarts to fall exponentially to zero.
- Cremains equal to the original charging voltage supply.
108The current in a DC circuit containing a fully charged capacitor is.
- Azero.
- Bis dependent upon the size of the capacitance of the capacitor.
- Cmaximum.
109 A capacitor is a barrier to.
- Aboth.
- BA.C.
- CD.C
110What is the total capacitance of a parallel circuit containing three capacitors with capacitance of 0.25microfarad, 0.03microfarad, and 0.12microfarad, respectively?.
- A0.4 µ(micro)F.
- B0.04 µ(micro)F.
- C0.04 piko Farad.
111When two capacitors are connected in series.
- Athe charge stored on each is inversely proportional to the voltage across it.
- Bthe charge stored on each is the same.
- Cthe charge stored on each is directly proportional to its capacitance
112The charge on a capacitor is expressed as.
- Athe ratio Q/V.
- Bthe product Q * V.
- Cthe product C * V.
113When handling a high voltage capacitor in an electrical circuit, be sure it.
- Ahas a full charge before removing it from the circuit.
- Bis fully discharged before removing it from the circuit.
- Chas at least a residual charge before removing it from the circuit
114The dielectric constant of a capacitor is a measurement of.
- Athe electrical resistance of the capacitor dielectric.
- Bthe electrostatic energy storing capacity of the capacitor dielectric.
- Cthe electrical repulsion of electrons within the dielectric material
115Three 12 microfarad capacitors in parallel. The overall circuit capacitance is.
- A4 microfarads.
- B1 microfarads.
- C36 microfarads.
116A circuit has 1 megohm and 8 microfarads. What is the time constant?.
- A8 seconds.
- B1 second.
- C40 seconds.
117 A capacitor rating is.
- Athe voltage it will charge to.
- Bthe maximum continuous voltage it can take.
- Cthe voltage it will rupture at
118The multiplier colour coding on a capacitor is in.
- Apicofarads.
- Bfarads.
- Cmicrofarads.
119The total capacitance of the circuit shown is.
- A36µ(micro)F.
- B4µ(micro)F.
- C3µ(micro)F.
120When a capacitor is charged from a DC supply, the voltage/time curve is.
- Alogarithmic.
- Blinear.
- Cexponential.
121An electrolytic capacitor is used because it has a.
- Asmall physical size for low leakage current.
- Blarge physical size for a large capacity.
- Csmall physical size for a large capacity
122An electrolytic capacitor would be used in circuits supplying.
- Aheavy loads.
- Blight loads.
- Cheavy / light loads.
123A 20 Picofarad capacitor with a 1 Megohm resistor takes how long to charge?.
- A100 microseconds.
- B20 milliseconds.
- C0.1 second.
124The discharge curve of a capacitor is.
- AExponential.
- BLogarithmic.
- CLinear
125What is the value of a monolithic capacitor with 103 on it?.
- A1000pf.
- B10,000pf.
- C100,000pf.
126What is the formula for working out the capacitance of a capacitor if K = dielectric constant, A = area of the plates, d = distance plates apart?.
- Ac = K*A/d.
- Bc = d/K*A.
- Cc = K*d/A.
127Total capacitance of 3 capacitors each 12milliFarad in a parallel circuit.
- A36milliFarad.
- B12milliFarad.
- C6mf.
128A combination of 1 megohm and 8 microfarad would give a time constant of.
- A40 seconds.
- B400 ms.
- C8 seconds
129Generally, what is the voltage across a fully charged capacitor?.
- ALess than circuit voltage.
- BSame as circuit voltage.
- CMore than circuit voltage.
130 When would you use an electrolytic capacitor?.
- AOn a balanced circuit.
- BLow output compared to size required.
- CLarge output compared to size required
131 A capacitor has Brown, Black and Orange bands. It's value is.
- A10 picofarads.
- B10 nanofarads.
- C100 picofarads.
132Voltage measured between the plates of a capacitor will be generally.
- Acan dangerously higher than applied voltage.
- Bthe same as applied voltage.
- Cless than applied voltage.
133Dielectric constant of a capacitor is.
- Amax V that can be applied to a capacitor.
- Belectrostatic storing capability of the dielectric.
- Cmax I stored in the capacitor
134One microfarad is.
- A1 * 10-12 farads.
- B1 * 1012 farads.
- C1 * 10-6 farads.
135A circuit with a capacitor has 6 volts applied to it with a charge of 2400 pico-coulombs. What would the charge be if the applied voltage was 1.5 volts ?.
- A2400 * 10-12 coulombs.
- B600 * 10-9 coulombs.
- C600 * 10-12 coulombs
136 In a capacitor, the dielectric strength is measured in.
- AFarads per meter.
- BVolts per metre.
- CCoulombs per m2.
137Three capacitors connected in series, each having a value of 12 picofarads, calculate the total capacitance.
- A36 picofarads.
- B4 picofarads.
- C12 picofarads.
138Magnetic inclination is the least at the.
- Apoles.
- Bequator.
- Cisoclines
139Ferromagnetic materials can be magnetized.
- Abelow a certain temperature.
- Babove a certain temperature.
- Cwithin a band of temperatures.
140Glass is an example of a.
- Acoercive material.
- Bparamagnetic material.
- Cdiamagnetic material
141 A solenoid of 10 turns per metre carries a current of 5A. If the current is reduced to 2.5A, how many turns would be required to maintain the same magnetic field?.
- A20.
- B50.
- C5.
142Which of the following materials is easiest to magnetize?.
- AHigh grade steel.
- BSoft iron.
- CCast iron
143To find which end of an electromagnet is the north pole, use the.
- AFleming's Left Hand Rule.
- BRight Hand Clasp Rule.
- CCork Screw Rule.
144The earth's magnetic field is greatest at the.
- Amagnetic equator.
- Bgeographic poles.
- Cmagnetic poles
145The lines of magnetic flux from a magnet will.
- Aattract each other.
- Brepel each other.
- Chave no effect upon each other
146Of the following which pair of materials would most readily become magnetized?.
- AIron and steel.
- BCopper and steel.
- CNickel and bronze.
147The core material used for an electromagnet is soft iron because.
- Aits magnetism is not easily destroyed.
- Bit retains most of its flux density when demagnetized.
- Cit demagnetizes easily.
148If the North pole of a magnet is brought nearer to the North pole of another magnet.
- Aattraction between them will be increased.
- Brepulsion between them will be reduced.
- Crepulsion between them will be increased.
149Where is the magnetic dip least?.
- APoles.
- BIsoclinals.
- CEquator.
150When a number of ferrite pieces are grouped together, they.
- Aare semi-permanent magnets when DC is passed through them.
- Belectromagnets.
- Ccan be used to store binary code.
151Ampere turns is calculated by the number of turns.
- Amultiplied by current.
- Bdivided by current.
- Cmultiplied by magnetic flux
152The unit of flux is the.
- AAmpere turns / metre.
- BWeber.
- CAmpere turns
153Lines of magnetic flux pass from.
- ASouth to North.
- BEast to West.
- CNorth to South.
154Why is ferrite used in memory circuits?.
- AHigh reluctance.
- BLow permeability.
- CHigh remanence.
155Magnetic lines are flowing parallel. They will.
- Ahave no effect on each other.
- Battract each other.
- Crepel each other
156The horizontal component of the earth's magnetic field is most strongly felt at.
- Aequator.
- B45 degrees latitude.
- Cpoles.
157Two parallel lines of magnetic flux in the same polarity.
- Arepel each other.
- Bhave no effect on each other.
- Cattract each other.
158Magnetic fields around two parallel conductors carrying current in the same directions will.
- Arepel.
- Battract.
- Cwill attract or repel depending on the type of current.
159Magnetic field on a solenoid is.
- Athe same both inside and outside the coil.
- Bweakest outside the coil.
- Cstrongest outside the coil.
160Which of the following is absolute permeability?.
- Aµ(micro)r.
- Bµo(micro node).
- Cµ(micro
161 A paramagnetic material has a relative permeability of.
- Azero.
- Bless than unity.
- Cgreater than unity.
162Through which material will magnetic lines of force pass the most readily?.
- ACopper.
- BIron.
- CAluminium.
163Permanent magnets have.
- Ahigh reluctance, high coercive force.
- Blow reluctance, high coercive force.
- Chigh reluctance, low coercive force
164The term used to denote the strength of a magnetic field is.
- Aretentivity.
- Bhysteresis.
- Cflux density
165 A soft iron core is used in an ELECTRO magnet because.
- Ait has LOW permeability and HIGH coercivity.
- Bit has HIGH permeability and LOW coercivity.
- Cit has HIGH permeability and HIGH coercivity.
166A non-magnetic metal.
- Ahas high retentivity.
- Bhas no permeability.
- Cis a poor conductor.
167What is the effect of inserting an iron core into a current carrying coil?.
- AThe flux density of the original magnetic field remains constant.
- BThe core tends to move from a stronger to a weaker part of the field.
- CThe flux density of the original magnetic field produced by the coil is increased
168Flux density will.
- Aincrease linearly with coercive force.
- Bdecrease linearly with magnetic flux.
- Cincrease linearly with magnetic flux
169Storage of magnets should be.
- Ain a non magnetic pox.
- Bin pairs with keeper plates.
- Cin pairs end to end
170The hysteresis loop for a magnetic material is on a graph with.
- Acurrent against flux density.
- Bflux density against magnetising force.
- Ctotal flux against flux density.
171A material with a narrow hysteresis loop.
- Acannot be magnetised.
- Bwill have high retentivity.
- Cwill have low retentivity
172If a bar magnet is cut in half.
- Athe magnet is destroyed.
- Btwo bar magnets are formed.
- Cone bar magnet and one non-magnet is formed
173Copper is a.
- Aferromagnetic material.
- Bparamagnetic materials.
- Cdiamagnetic material
174The MMF of a coil fed with 2 amps and having 10 turns is.
- A5 ampere turns.
- B20 amperes / turn.
- C20 ampere turns.
175An example of a paramagnetic material is.
- Asilver.
- Biron.
- Cglass
176Vibration in a magnet causes.
- Aflux to stay the same.
- Bflux to decrease.
- Cflux to increase
177Permeability of a material can be found by.
- Aflux density / MMF.
- BMMF * flux density.
- CMMF / flux density.
178When magnetizing a piece of material, magnetic strength will rise.
- Anon-linearly with magnetic force.
- Blinearly with coercive force.
- Clinearly with magnetic force
179A material exposed to heat will.
- Ahave no effect on magnetism.
- Bbe easier to magnetise.
- Cbe harder to magnetise.
180If cobalt has a permeability of 4800 it is a.
- Aferromagnetic.
- Bparamagnetic.
- Cdiamagnetic.
181Cobalt has a permeability.
- Agreater than unity.
- Bless than unity.
- Csame as unity.
182Magnetic flux.
- Aexist in all space around the magnet.
- Bis more concentrated at the centre of bar magnet.
- Coccupies the space around the magnet with equal flux density.
183The ability of a circuit to produce a magnetic flux under the influence of a MMF.
- Apermeance.
- Bpermeability.
- Cpermanence
184Magnetic flux saturation takes place when.
- Athe magnetised medium will accept no further lines of flux.
- Bthe magnetic field drops to zero.
- Cthe magnetic field starts to reduce with increased magnetising force
185Cables are shielded to prevent 'H' magnetic interference in wires with the following material.
- ACopper braiding.
- BFerromagnetic material.
- CDiamagnetic material
186Spontaneous magnetism is associated with.
- Adiamagnetic materials.
- Bferromagnetic materials.
- Cparamagnetic materials
187Two inductive coils are placed in close proximity with each other at 90 degrees. The number of flux linkages is.
- A0.
- Bmaximum negative.
- Cmaximum positive.
188What is the mutual inductance if two coils of 10mH and 500mH have 90% of the flux transferred from one to the other?.
- A459mH.
- B4.5mH.
- C63mH.
189An inductor has 1,000 turns of wire and a cross sectional area of 0.001m2. If the core has a permeability of 0.000,001 and the coil is 0.1m. What is the value of the inductor?.
- A100microH.
- B100mH.
- C10mH
190Three inductors 10 mH, 5 mH and 20 mH are connected in parallel. What is the total inductance?.
- AWithout knowing the coupling factor the total inductance cannot be found.
- B2.86mH.
- C35mH.
191If the current reaches a maximum through an inductor of 2A in 15 seconds, what is the current after 3 seconds?.
- A1.26A.
- B0.63A.
- C1A.
192The time constant of an inductor is.
- AL/R.
- BL2 /R.
- CLR.
193If the rate of change of current is halved, mutual inductance will.
- Astay the same.
- Bhalve.
- Cdouble.
194Why are the iron cores of most induction coils laminated?.
- ATo reduce the effects of eddy currents.
- BTo reduce the core reluctance.
- CTo increase the core permeability
195When more than two inductors of different inductance are connected in parallel in a circuit, the total inductance is.
- Aequal to the sum of the individual inductance.
- Bequal to the inductance of the highest rated inductor.
- Cless than the inductance of the lowest rated inductor.
196The time constant in an inductive circuit is the time required for the current to reach.
- A70.7% of maximum value.
- B63.2% of maximum value.
- C63.7% of maximum value.
197An AC inductive circuit has an inductance 0f 10 mH and a frequency input of 1000Hz. The opposition to current flow is approximately.
- A63 ohms.
- B63,000 ohms.
- C630 ohms
198Rotating coil B through 90° will.
- Aincrease the EMF induced into B.
- Bincrease the EMF induced into A.
- Cdecrease the EMF induced into B.
199An inductor of resistance 5 kΩ and inductance 2mH is connected to a DC circuit. The time constant is.
- A400 ns.
- B10 seconds.
- C40 ms.
200When switching off the supply, the back EMF in a collapsing field in an inductor.
- Acan be multiple times bigger than forward EMF.
- Bnever exceeds forward EMF.
- Cis equal to forward EMF.
Informationen
- Beschreibung
- Quiz am Física 2, erstellt von oriol arrufat am 12/10/2018.
- Autor
- oriol arrufat
- Sprache
- English
- Aufrufe
- 0
- Bewertung
- Noch keine Bewertungen Bewerte dieses Quiz