3. Communications

Question 1

What is the purpose of the RMPs?

Accepted Answer

Give the flight crew control of all VHF and HF radio communication systems, and to provide back up to the FMGCs for controlling radio navigation systems

Answer

VHF and HF radio communication systems only

Answer

Provide radio navigation systems only

Answer

Automatically tune navaids as required by the flight plan

Question 2

In normal operation, RMP 1 is dedicated to:

Accepted Answer

VHF 1 and HF1

Answer

HF 1 and HF 2

Answer

VHF 2

Answer

HF 2

Question 3

If RMP 1 fails:

Accepted Answer

the remaining RMPs control all VHF or HF transceivers

Answer

whole system is inoperative

Answer

VHF2 and HF 2 frequencies cannot be controlled

Answer

only VHF 2 frequencies cannot be controlled

Question 4

The ON/OFF switch on the RMP controls

Accepted Answer

Power supply to the RMP

Answer

The STBY NAV function of the RMP

Answer

The HF function of the RMP

Answer

Activates the beat frequency oscillator

Question 5

If you select VHF 2 on RMP 1 the white SEL light illuminates on

Accepted Answer

RMP 1 & RMP 2

Answer

RMP1, RMP 2 & RMP 3

Answer

RMP 1 only

Answer

RMP 2 only

Question 6

When would a green AM light illuminate on RMP 1?

Accepted Answer

if AM mode is required and crew has selected HF 1 and AM

Answer

would not illuminate

Answer

if crew has selected HF1 and single side band mode

Answer

if AM mode is required and crew has selected HF 2 and AM

Question 7

A VOR is tuned on RMP 1 using the STBY NAV function. Can this selection be seen on the MCDU RAD NAV page?

Accepted Answer

no - information on RAD NAV page is not available when the NAV pb on RMP is pressed

Answer

yes - information on RAD NAV page is always available

Answer

no - it is not possible to tune a VOR using STBY NAV function

Answer

yes - MCDU RAD NAV page shows VORs tuned using STBY NAV function

Question 8

Is it possible to tune a navaid with the STBY NAV function on RMP 3?

Accepted Answer

no - STBY NAV function is not available on RMP 3

Answer

yes

Answer

no - RMP 3 is not available for crew use

Answer

yes - but only on the ground

Question 9

How can a navaid tuned through the STBY NAV on RMP 1 or 2 be identified?

Accepted Answer

The ident appears on the ND and by pressing out the corresponding reception knob on the ACP

Answer

The ident appears on the upper ECAM display

Answer

You cannot identify navaids tuned through STBY NAV

Answer

By pressing a line select key on the MCDU

Question 10

Can you select VOR 2 using the STBY NAV function on RMP 1?

Accepted Answer

No - with STBY NAV function VOR 1 can only be selected on RMP 1

Answer

Yes - RMP 1 can control all radios in STBY NAV

Answer

Yes - by selecting VOR 2 key on RMP 1

Answer

No - VOR 2 cannot be tuned through STBY NAV function

Question 11

If VHF 1 is selected on RMP 2, the SEL light illuminates white on

Accepted Answer

On RMP 1 & 2

Answer

On RMP 2 only

Answer

On RMP 1 only

Answer

On RMP 1, 2 & 3

Question 12

If RMP 1 fails

Accepted Answer

Switch off RMP 1 and use remaining RMPs

Answer

Put AUDIO SWITCHING selector on overhead panel to CAPT 3

Answer

HF is not available

Answer

STBY NAV function is not available

Question 13

In the event of both FMGCs failing how can navaids be tuned

Accepted Answer

By using RMP 1 & 2

Answer

By using RMP 1 only

Answer

By using RMP 1, 2 & 3

Answer

navaids can only be tuned through the MCDU RAD NAV page

Question 14

If the NAV key on the RMP 2 has been pressed to select STBY NAV

Accepted Answer

Selection of the NAV key does not affect the selection of communication radios and their frequencies

Answer

VHF function is lost on the RMP 2

Answer

VHF reception is lost on ACP 2

Answer

VHF is still available but only the last selected frequency can be used as long as NAV is pressed

Question 15

If an RMP fails

Accepted Answer

The selected receiver is no longer controlled by this RMP

Answer

The selected receiver is controlled by RMP 1

Answer

The frequency displays appear

Answer

The green VHF or HF lights go on

Question 16

When a SELCAL is received on VHF 2

Accepted Answer

CALL flashes in amber on the VHF 2 transmission key and a buzzer sounds

Answer

Three green bars come on in the VHF 2 transmission key and a buzzer sounds

Answer

White SELCAL appears on the VHF 2 transmission key and the VHF 2 reception knob illuminates white

Answer

SELCAL flashes in amber on the VHF 2 transmission key and a buzzer sounds

Question 17

With the MECH transmission key on the Audio Control Panel (ACP) pressed

Accepted Answer

The flight interphone channel is selected for transmission via the ACP RAD switch or the side stick radio selector

Answer

The cabin interphone channel is selected for transmission via the ACP RAD switch

Answer

You can speak to the ground mechanic via the handset

Answer

The mechanic will hear the external horn sound

Question 18

How could you receive ATIS information from a VOR

Accepted Answer

Pressing and releasing out the VOR reception knob and selecting the ON VOICE key on the ACP

Answer

Pressing the ON VOICE key on the ACP

Answer

Voice facility is not available through the ACP

Answer

Pressing the ATIS button on the Captain’s ACP

Question 19

How do you cancel the ON VOICE green light?

Accepted Answer

by depressing the on voice p/b

Answer

by pressing in the VOR reception knob

Answer

by pressing in the ATIS button on the Captain’s ACP

Answer

by pressing the RESET key

Question 20

What is the function of the RESET p/b on the ACP?

Accepted Answer

To extinguish the CALL, MECH or ATT amber lights if illuminated

Answer

To restart system operation

Answer

To cancel previous transmission key selection

Answer

to cancel previous reception knob selections

Question 21

when CAPT 3 is selected on AUDIO SWITCHING panel on the overhead panel

Accepted Answer

The Captain uses his acoustic equipment and the third occupant’s ACP

Answer

The third occupant uses the Captain’s equipment

Answer

The Captain uses the third occupant’s headset

Answer

The Captain uses the third occupant’s headset and ACP

Question 22

The aircraft interphone systems allow the flight crew members to communicate with

Accepted Answer

The cabin attendants, the cockpit, and the mechanic

Answer

Only cabin attendants

Answer

Only the Captain

Answer

Only the mechanic

Question 23

Can you use the cabin interphone system in flight?

Accepted Answer

Yes - to communicate with the cabin crew

Answer

Yes - to communicate with the other occupants of the cockpit

Answer

No - service interphone is used only to communicate with mechanic on the ground

Answer

No - service interphone system deactivated in flight

Question 24

Can you speak on VHF and the PA at the same time?

Accepted Answer

Never - because when PA transmission key is pressed the previous transmission key is deselected

Answer

Yes - by pressing RAD switch and PA key on ACP

Answer

Yes - by using sidestick radio switch and PA key on ACP

Answer

Yes - by using hand mike for PA and boom mike for VHF

Question 25

Which selection must be made to communicate with the ground mechanic at the engine nacelle interphone jack

Accepted Answer

ATT transmission key pressed, CAB reception knob released out, use RAD position on ACP

Answer

MECH transmission key pressed, INT reception knob released out, use RAD position on ACP

Answer

ENG transmission key pressed, use INT position on ACP

Answer

Use INT position on ACP, INT reception knob released out, and no transmission key necessary

Question 26

On the overhead panel with the CAPT & PURS/CAPT switch in the CAPT & PURS position

Accepted Answer

The evac alert may be activated from the cockpit or the fwd or aft attendant positions

Answer

The evac alert may only be activated from the cockpit

Answer

The evac alert may be activated from any cabin crew station

Answer

The evac alert may be activated from the cockpit and any cabin crew position

Question 27

CVR is energised

Accepted Answer

All the above are correct

Answer

GND CTL p/b is pressed ON

Answer

On the ground during first 5 minutes after energization of the aircraft electrical network or with one engine running

Answer

In flight

Question 28

The CVR recording can be erased by

Accepted Answer

pressing the CVR ERASE p/b for 2 seconds when aircraft is on the ground and the parking brake is on

Answer

Cannot be erased except by maintenance

Answer

Pressing the CVR ERASE p/b once

Answer

Pressing the CVR ERASE p/b for 2 seconds in flight

Question 29

How can the CVR be tested before engine start?

Accepted Answer

Pressing the CVR GND CTL p/b ON and pressing the CVR TEST p/b with the parking brake set

Answer

pressing the CVR GND CTL p/b ON and pressing the CVR TEST p/b

Answer

Pressing the CVR TEST p/b with the parking brake released

Answer

Can only be tested after engine start

Question 30

On the ground the crew can manually energise the CVR by pressing

Accepted Answer

The ground control p/b

Answer

The CVR erase p/b

Answer

The CVR test p/b

Answer

It is not possible to manually energise the CVR

Question 31

If an ELT is triggered by an impact in armed mode signal transmission can be stopped by

Accepted Answer

Pressing the TEST/RESET p/b on the overhead panel

Answer

Pressing the ELT CUTOFF p/b on the overhead panel

Answer

Pressing the ELT shutoff p/b on the external power panel

Answer

Transmission cannot be stopped

Question 32

With ATC (transponder) mode selector at AUTO

Accepted Answer

Selected ATC operate in flight, and on the ground with Mode S

Answer

Selected ATC operates when FLEX or TOGA power is set for take-off

Answer

Selected ATC operates as soon as one engine is running

Answer

TA/RA function is automatically selected

Question 33

The ATC FAIL light illuminates on the ATC control panel on the pedestal

Accepted Answer

selected transponder has failed

Answer

TCAS not available

Answer

System 1 or 2 has failed

Answer

Incorrect ATC code set

3. Communications

Crea una cuenta gratis para terminar este test

Información

Escríbenos

¿Qué te parece el nuevo diseño?