Test
CISCO 2 - Chapter 1 bis Chapter 4
Preguntas del test (93)
1A network administrator enters the command copy running-config startup-config. Which type of memory will the startup configuration be placed into?
- AROM
- BNVRAM
- CRAM
- Dflash
2Which packet-forwarding method does a router use to make switching decisions when it is using a forwarding information base and an adjacency table?
- Aflow process
- Bprocess switching
- CCisco Express Forwarding
- Dfast switching
3What are two functions of a router? (Choose two.)
- AIt builds a routing table based on ARP requests.
- BIt provides segmentation at Layer 2.
- CIt determines the best path to send packets.
- DIt controls the flow of data via the use of Layer 2 addresses.
- EA router connects multiple IP networks.
4In order for packets to be sent to a remote destination, what three pieces of information must be configured on a host? (Choose three.)
- ADHCP server address
- BDNS server address
- Cdefault gateway
- Dsubnet mask
- EIP address
- Fhostname
5Which software is used for a network administrator to make the initial router configuration securely?
- Aterminal emulation client software
- BHTTPS client software
- CTelnet client software
- DSSH client software
6Refer to the exhibit. A network administrator has configured R1 as shown. When the administrator checks the status of the serial interface, the interface is shown as being administratively down. What additional command must be entered on the serial interface of R1 to bring the interface up?
- AIPv6 enable
- Bno shutdown
- Cend
- Dclockrate 128000
7What is a characteristic of an IPv4 loopback interface on a Cisco IOS router?
- AIt is assigned to a physical port and can be connected to other devices.
- BOnly one loopback interface can be enabled on a router.
- CIt is a logical interface internal to the router.
- DThe no shutdown command is required to place this interface in an UP state.
8What two pieces of information are displayed in the output of the show ip interface brief command? (Choose two.)
- Aspeed and duplex settings
- Binterface descriptions
- Cnext-hop addresses
- DLayer 1 statuses
- EMAC addresses
- FIP addresses
9Which two items are used by a host device when performing an ANDing operation to determine if a destination address is on the same local network? (Choose two.)
- Anetwork number
- Bsubnet mask
- Csource MAC address
- Ddestination IP address
- Edestination MAC address
10Refer to the exhibit. PC A sends a request to Server B. What IPv4 address is used in the destination field in the packet as the packet leaves PC A?
- A192.168.11.1
- B192.168.12.16
- C192.168.10.1
- D192.168.10.10
11What does R1 use as the MAC address of the destination when constructing the frame that will go from R1 to Server B?
- AThe packet is encapsulated into a PPP frame, and R1 adds the PPP destination address to the frame.
- BR1 leaves the field blank and forwards the data to the PC.
- CR1 uses the destination MAC address of S1.
- DIf the destination MAC address that corresponds to the IPv4 address is not in the ARP cache, R1 sends an ARP request.
12Refer to the exhibit. If PC1 is sending a packet to PC2 and routing has been configured between the two routers, what will R1 do with the Ethernet frame header attached by PC1?
- Aremove the Ethernet header and configure a new Layer 2 header before sending it out S0/0/0
- Bopen the header and use it to determine whether the data is to be sent out S0/0/0
- Copen the header and replace the destination MAC address with a new one
- Dnothing, because the router has a route to the destination network
13Refer to the exhibit. What will the router do with a packet that has a destination IP address of 192.168.12.227?
- ASend the packet out the Serial0/0/0 interface.
- BSend the packet out the GigabitEthernet0/1 interface.
- CSend the packet out the GigabitEthernet0/0 interface.
- DDrop the packet.
14Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)
- AThe metric varies depending which Layer 3 protocol is being routed, such as IP.
- BThe metric is always determined based on hop count.
- CRoutes with the smallest metric to a destination indicate the best path.
- DThe value of the administrative distance can not be altered by the network administrator.
- EA router first installs routes with higher administrative distances.
- FAdministrative distance refers to the trustworthiness of a particular route.
15Which two parameters are used by EIGRP as metrics to select the best path to reach a network? (Choose two.)
- Aconfidentiality
- Bresiliency
- Cjitter
- Ddelay
- Ebandwidth
- Fhop count
16What route would have the lowest administrative distance?
- Aa route received through the OSPF routing protocol
- Ba route received through the EIGRP routing protocol
- Ca static route
- Da directly connected network
17Consider the following routing table entry for R1:
D 10.1.1.0/24 [90/2170112] via 209.165.200.226, 00:00:05, Serial0/0/0
What is the significance of the Serial0/0/0?- AIt is the interface on the next-hop router when the destination IP address is on the 10.1.1.0/24 network.
- BIt is the interface on the final destination router that is directly connected to the 10.1.1.0/24 network.
- CIt is the R1 interface through which the EIGRP update was learned.
- DIt is the interface on R1 used to send data that is destined for 10.1.1.0/24.
18Which two statements correctly describe the concepts of administrative distance and metric? (Choose two.)
- AThe metric varies depending on which Layer 3 protocol is being routed.
- BThe metric is always determined based on hop count.
- CRoutes with the smallest metric to a destination indicate the best path.
- DThe value of the administrative distance cannot be altered by the network administrator.
- EA router first installs routes with higher administrative distances.
- FAdministrative distance refers to the trustworthiness of a particular route.
19Refer to the exhibit. A network administrator issues the show ipv6 route command on R1. What two conclusions can be drawn from the routing table? (Choose two.)
- AThe network FF00::/8 is installed through a static route command.
- BPackets that are destined for the network 2001:DB8:ACAD:2::54/128 will be forwarded through Fa0/0.
- CPackets that are destined for the network 2001:DB8:ACAD:2::/64 will be forwarded through Fa0/1.
- DThe interface Fa0/1 is configured with IPv6 address 2001:DB8:ACAD:A::12.
- ER1 does not know a route to any remote networks.
20A network administrator configures the interface fa0/0 on the router R1 with the command ip address 172.16.1.254 255.255.255.0. However, when the administrator issues the command show ip route, the routing table does not show the directly connected network. What is the possible cause of the problem?
- AThe subnet mask is incorrect for the IPv4 address.
- BNo packets with a destination network of 172.16.1.0 have been sent to R1.
- CThe configuration needs to be saved first.
- DThe interface fa0/0 has not been activated.
21A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226. What is the purpose of this command?
- Ato provide a route to forward packets for which there is no route in the routing table
- Bto forward packets destined for the network 0.0.0.0 to the device with IP address 209.165.200.226
- Cto add a dynamic route for the destination network 0.0.0.0 to the routing table
- Dto forward all packets to the device with IP address 209.165.200.226
22What are two common types of static routes in routing tables? (Choose two)
- Aa static route shared between two neighboring routers
- Ba static route converted from a route that is learned through a dynamic routing protocol
- Ca static route to a specific network
- Da built-in static route by IOS
- Ea default static route
23What is the effect of configuring the ipv6 unicast-routing command on a router?
- Ato prevent the router from joining the all-routers multicast group
- Bto permit only unicast packets on the router
- Cto enable the router as an IPv6 router
- Dto assign the router to the all-nodes multicast group
24What are two advantages of static routing over dynamic routing? (Choose two.)
- AStatic routing is relatively easy to configure for large networks.
- BStatic routing uses fewer router resources than dynamic routing.
- CStatic routing requires very little knowledge of the network for correct implementation.
- DStatic routing scales well with expanding networks.
- EStatic routing is more secure because it does not advertise over the network.
25Refer to the exhibit. What routing solution will allow both PC A and PC B to access the Internet with the minimum amount of router CPU and network bandwidth utilization?
- AConfigure a static default route from R1 to Edge, a default route from Edge to the Internet, and a static route from Edge to R1.
- BConfigure a dynamic routing protocol between R1 and Edge and advertise all routes.
- CConfigure a dynamic route from R1 to Edge and a static route from Edge to R1.
- DConfigure a static route from R1 to Edge and a dynamic route from Edge to R1.
26What is the correct syntax of a floating static route?
- Aip route 172.16.0.0 255.248.0.0 10.0.0.1
- Bip route 0.0.0.0 0.0.0.0 serial 0/0/0
- Cip route 209.165.200.228 255.255.255.248 10.0.0.1 120
- Dip route 209.165.200.228 255.255.255.248 serial 0/0/0
27What is a characteristic of a static route that matches all packets?
- AIt is configured with a higher administrative distance than the original dynamic routing protocol has.
- BIt identifies the gateway IP address to which the router sends all IP packets for which it does not have a learned or static route.
- CIt uses a single network address to send multiple static routes to one destination address.
- DIt backs up a route already discovered by a dynamic routing protocol.
28What type of route allows a router to forward packets even though its routing table contains no specific route to the destination network?
- Ageneric route
- Bdestination route
- Cdefault route
- Ddynamic route
29Why would a floating static route be configured with an administrative distance that is higher than the administrative distance of a dynamic routing protocol that is running on the same router?
- Ato be the priority route in the routing table
- Bto act as a gateway of last resort
- Cto load-balance the traffic
- Dto be used as a backup route
30A company has several networks with the following IP address requirements:
IP phones – 50
PCs – 70
IP cameras – 10
wireless access points – 10
network printers – 10
network scanners – 2
Which block of addresses would be the minimum to accommodate all of these devices if each type of device was on its own network?- A172.16.0.0/22
- B172.16.0.0/23
- C172.16.0.0/24
- D172.16.0.0/25
31What happens to a static route entry in a routing table when the outgoing interface associated with that route goes into the down state?
- AThe router automatically redirects the static route to use another interface.
- BThe static route remains in the table because it was defined as static.
- CThe router polls neighbors for a replacement route.
- DThe static route is removed from the routing table.
32The network administrator configures the router with the ip route 172.16.1.0 255.255.255.0 172.16.2.2 command. How will this route appear in the routing table?
- AS 172.16.1.0 [1/0] via 172.16.2.2
- BC 172.16.1.0 [1/0] via 172.16.2.2
- CS 172.16.1.0 is directly connected, Serial0/0
- DC 172.16.1.0 is directly connected, Serial0/0
33Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (Choose two.)
- AA(config)# no ip route 10.0.0.0 255.0.0.0 172.16.40.2
- BA(config)# ip route 10.0.0.0 255.0.0.0 192.168.1.2
- CA(config)# ip route 10.0.0.0 255.0.0.0 s0/0/0
- DA(config)# no ip address 10.0.0.1 255.0.0.0 172.16.40.2
- EA(config)# no network 10.0.0.0 255.0.0.0 172.16.40.2
34Which type of static route that is configured on a router uses only the exit interface?
- Adefault static route
- Bfully specified static route
- Cdirectly connected static route
- Drecursive static route
35Refer to the graphic. Which command would be used on router A to configure a static route to direct traffic from LAN A that is destined for LAN C?
- AA(config)# ip route 192.168.4.0 255.255.255.0 192.168.5.2
- BA(config)# ip route 192.168.3.2 255.255.255.0 192.168.4.0
- CA(config)# ip route 192.168.3.0 255.255.255.0 192.168.3.1
- DA(config)# ip route 192.168.5.0 255.255.255.0 192.168.3.2
- EA(config)# ip route 192.168.4.0 255.255.255.0 192.168.3.2
36Refer to the exhibit. The network administrator needs to configure a default route on the Border router. Which command would the administrator use to configure a default route that will require the least amount of router processing when forwarding packets?
- ABorder(config)# ip route 0.0.0.0 0.0.0.0 198.133.219.5
- BBorder(config)# ip route 0.0.0.0 0.0.0.0 s0/0/0
- CBorder(config)# ip route 0.0.0.0 0.0.0.0 s0/0/1
- DBorder(config)# ip route 0.0.0.0 0.0.0.0 198.133.219.6
37What two pieces of information are needed in a fully specified static route to eliminate recursive lookups? (Choose two.)
- Athe IP address of the exit interface
- Bthe administrative distance for the destination network
- Cthe IP address of the next-hop neighbor
- Dthe interface ID of the next-hop neighbor
- Ethe interface ID exit interface
38Refer to the exhibit. What command would be used to configure a static route on R1 so that traffic from both LANs can reach the 2001:db8:1:4::/64 remote network?
- Aipv6 route ::/0 serial0/0/0
- Bipv6 route 2001:db8:1::/65 2001:db8:1:3::1
- Cipv6 route 2001:db8:1:4::/64 2001:db8:1:3::2
- Dipv6 route 2001:db8:1:4::/64 2001:db8:1:3::1
39Refer to the exhibit. Which default static route command would allow R1 to potentially reach all unknown networks on the Internet?
- AR1(config)# ipv6 route 2001:db8:32::/64 G0/0
- BR1(config)# ipv6 route 2001:db8:32::/64 G0/1 fe80::2
- CR1(config)# ipv6 route ::/0 G0/1 fe80::2
- DR1(config)# ipv6 route ::/0 G0/0 fe80::2
40Consider the following command:
ip route 192.168.10.0 255.255.255.0 10.10.10.2 5
Which route would have to go down in order for this static route to appear in the routing table?- Aan EIGRP-learned route to the 192.168.10.0/24 network
- Ban OSPF-learned route to the 192.168.10.0/24 network
- Ca static route to the 192.168.10.0/24 network
- Da default route
41Refer to the exhibit. The routing table for R2 is as follows:
Gateway of last resort is not set
10.0.0.0/30 is subnetted, 2 subnets
C 10.0.0.0 is directly connected, Serial0/0/0
C 10.0.0.4 is directly connected, Serial0/0/1
192.168.10.0/26 is subnetted, 3 subnets
S 192.168.10.0 is directly connected, Serial0/0/0
C 192.168.10.64 is directly connected, FastEthernet0/0
S 192.168.10.128 [1/0] via 10.0.0.6
What will router R2 do with a packet destined for 192.168.10.129?
- Adrop the packet
- Bsend the packet out interface FastEthernet0/0
- Csend the packet out interface Serial0/0/1
- Dsend the packet out interface Serial0/0/0
42A network administrator has entered a static route to an Ethernet LAN that is connected to an adjacent router. However, the route is not shown in the routing table. Which command would the administrator use to verify that the exit interface is up?
- Atracert
- Bshow ip route
- Cshow ip protocols
- Dshow ip interface brief
43Consider the following command:
ip route 192.168.10.0 255.255.255.0 10.10.10.2 5
How would an administrator test this configuration?- APing from the 192.168.10.0 network to the 10.10.10.2 address
- BManually shut down the router interface used as a primary route.
- CPing any valid address on the 192.168.10.0/24 network.
- DDelete the default gateway route on the router.
44Refer to the exhibit. The small company shown uses static routing. Users on the R2 LAN have reported a problem with connectivity. What is the issue?
- AR2 needs a static route to the R1 LANs.
- BR2 needs a static route to the Internet.
- CR1 needs a static route to the R2 LAN.
- DR1 needs a default route to R2.
- ER1 and R2 must use a dynamic routing protocol.
45Which three IOS troubleshooting commands can help to isolate problems with a static route? (Choose three.)
show version- Ashow arp
- Bshow ip interface brief
- Cshow ip route
- Dtracert
- Eping
46An administrator issues the ipv6 route 2001:db8:acad:1::/32 gigabitethernet0/0 2001:db8:acad:6::1 100 command on a router. What administrative distance is assigned to this route?
- A100
- B32
- C1
- D0
47Refer to the exhibit. The network engineer for the company that is shown wants to use the primary ISP connection for all external connectivity. The backup ISP connection is used only if the primary ISP connection fails. Which set of commands would accomplish this goal?
- Aip route 198.133.219.24 255.255.255.252
ip route 64.100.210.80 255.255.255.252 - Bip route 0.0.0.0 0.0.0.0 s0/0/0
ip route 0.0.0.0 0.0.0.0 s0/1/0 10 - Cip route 0.0.0.0 0.0.0.0 s0/0/0
ip route 0.0.0.0 0.0.0.0 s0/1/0 - Dip route 198.133.219.24 255.255.255.252
ip route 64.100.210.80 255.255.255.252 10
- Aip route 198.133.219.24 255.255.255.252
48Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Why are the pings from PC0 to Server0 not successful?- AThe static route to network 192.168.2.0 is misconfigured on Router2.
- BThe static route to network 192.168.2.0 is misconfigured on Router1.
- CThe static route to network 192.168.1.0 is misconfigured on Router2.
- DThe static route to network 192.168.1.0 is misconfigured on Router1.
49What IPv6 static route can be configured on router R1 to make a fully converged network?
- Aipv6 route 2001:db8:10:12::/64 S0/0/1
- Bipv6 route 2001:db8:10:12::/64 2001:db8:32:77::1
- Cipv6 route 2001:db8:10:12::/64 2001:db8:10:12::1
- Dipv6 route 2001:db8:10:12::/64 S0/0/0
50Which dynamic routing protocol was developed to interconnect different Internet service providers?
- ARIP
- BOSPF
- CEIGRP
- DBGP
51Which routing protocol is limited to smaller network implementations because it does not accommodate growth for larger networks?
- AIS-IS
- BEIGRP
- CRIP
- DOSPF
52What two tasks do dynamic routing protocols perform? (Choose two.)
- Aassign IP addressing
- Bnetwork discovery
- Cpropagate host default gateways
- Dupdate and maintain routing tables
- Ediscover hosts
53When would it be more beneficial to use a dynamic routing protocol instead of static routing?
- Aon a network where there is a lot of topology changes
- Bin an organization where routers suffer from performance issues
- Con a stub network that has a single exit point
- Din an organization with a smaller network that is not expected to grow in size
54When would it be more beneficial to use static routing instead of dynamic routing protocols?
- Aon a network that commonly experiences link failures
- Bon a network that has a large amount of redundant paths
- Con a network that is expected to continually grow in size
- Don a network where dynamic updates would pose a security risk
55What is a purpose of the network command when configuring RIPv2 as the routing protocol?
- AIt populates the routing table with the network entry.
- BIt immediately advertises the specified network to neighbor routers with a classful mask.
- CIt specifies the remote network that can now be reached.
- DIt identifies the interfaces that belong to a specified network.
56A network administrator configures a static route on the edge router of a network to assign a gateway of last resort. How would a network administrator configure the edge router to automatically share this route within RIP?
- AUse the default-information originate command.
- BUse the network command.
- CUse the passive-interface command.
- DUse the auto-summary command.
57What is the purpose of the passive-interface command?
- Aallows a router to receive routing updates on an interface but not send updates via that interface
- Ballows interfaces to share IP addresses
- Callows an interface to remain up without receiving keep alives
- Dallows a router to send routing updates on an interface but not receive updates via that interface
- Eallows a routing protocol to forward updates out an interface that is missing its IP address
58Which route would be automatically created when a router interface is activated and configured with an IP address?
- AO 172.16.0.0/16 [110/65] via 192.168.5.1
- BS 192.168.1.0/24 is directly connected, FastEthernet 0/1
- CC 192.168.0.0/24 is directly connected, FastEthernet 0/0
- DD 10.16.0.0/24 [90/3256] via 192.168.6.9
59What occurs next in the router lookup process after a router identifies a destination IP address and locates a matching level 1 parent route?
- AThe router drops the packet.
- BThe level 1 ultimate routes are examined.
- CThe level 1 supernet routes are examined.
- DThe level 2 child routes are examined.
60Which route would be used to forward a packet with a source IP address of 192.168.10.1 and a destination IP address of 10.1.1.1?
- AS 0.0.0.0/0 [1/0] via 172.16.1.1
- BO 10.1.1.0/24 [110/65] via 192.168.200.2, 00:01:20, Serial0/1/0
- CS 10.1.0.0/16 is directly connected, GigabitEthernet0/0
- DC 192.168.10.0/30 is directly connected, GigabitEthernet0/1
61Which two requirements are used to determine if a route can be considered as an ultimate route in a router’s routing table? (Choose two.)
- Acontain a next-hop IP address
- Bbe a classful network entry
- Ccontain an exit interface
- Dbe a default route
- Econtain subnets
62What is a disadvantage of using dynamic routing protocols?
- AThey require administrator intervention when the pathway of traffic changes.
- BThey send messages about network status insecurely across networks by default.
- CTheir configuration complexity increases as the size of the network grows.
- DThey are only suitable for simple topologies.
63Which two statements are true regarding classless routing protocols? (Choose two.)
- Areduces the amount of address space available in an organization
- Ballows for use of both 192.168.1.0/30 and 192.168.1.16/28 subnets in the same topology
- Cis supported by RIP version 1
- Dsends complete routing table update to all neighbors
- Esends subnet mask information in routing updates
64While configuring RIPv2 on an enterprise network, an engineer enters the command network 192.168.10.0 into router configuration mode.
What is the result of entering this command?- AThe interface of the 192.168.10.0 network is sending RIP hello messages.
- BThe interface of the 192.168.10.0 network is sending only version 2 updates.
- CThe interface of the 192.168.10.0 network is receiving version 1 and version 2 updates.
- DThe interface of the 192.168.10.0 network is sending version 1 and version 2 updates.
65A destination route in the routing table is indicated with a code D. Which kind of route entry is this?
- Aa route dynamically learned through the EIGRP routing protocol
- Ba network directly connected to a router interface
- Ca route used as the default gateway
- Da static route
66Which type of route will require a router to perform a recursive lookup?
- Aa parent route on a router that is using CEF
- Ba level 1 network route that is using a next hop IP address on a router that is using CEF
- Ca level 2 child route that is using an exit interface on a router that is not using CEF
- Dan ultimate route that is using a next hop IP address on a router that is not using CEF
67Which route is the best match for a packet entering a router with a destination address of 10.16.0.2?
- AS 10.0.0.0/16 is directly connected, Ethernet 0/0
- BS 10.16.0.0/16 is directly connected, Ethernet 0/1
- CS 10.16.0.0/24 [1/0] via 192.168.0.9
- DS 10.0.0.0/8 [1/0] via 192.168.0.2
68A router is configured to participate in multiple routing protocol: RIP, EIGRP, and OSPF. The router must send a packet to network 192.168.14.0. Which route will be used to forward the traffic?
- Aa 192.168.14.0/25 route that is learned via RIP
- Ba 192.168.14.0/25 route that is learned via OSPF
- Ca 192.168.14.0/24 route that is learned via EIGRP
- Da 192.168.14.0/26 route that is learned via RIP
69What is different between IPv6 routing table entries compared to IPv4 routing table entries?
- AIPv6 does not use static routes to populate the routing table as used in IPv4.
- BThe selection of IPv6 routes is based on the shortest matching prefix, unlike IPv4 route selection which is based on the longest matching prefix.
- CBy design IPv6 is classless so all routes are effectively level 1 ultimate routes.
- DIPv6 routing tables include local route entries which IPv4 routing tables do not.
70Refer to the exhibit. Which two types of routes could be used to describe the 192.168.200.0/30 route? (Choose two.)
- Aultimate route
- Bsupernet route
- Clevel 2 child route
- Dlevel 1 network route
- Elevel 1 parent route
71Refer to the exhibit. Based on the partial output from the show ip route command, what two facts can be determined about the RIP routing protocol? (Choose two.)
- ARIP version 2 is running on this router and its RIP neighbor.
- BRIP will advertise two networks to its neighbor.
- CThe command no auto-summary has been used on the RIP neighbor router.
- DRIP version 1 is running on this router and its RIP neighbor.
- EThe metric to the network 172.16.0.0 is 120.
72Refer to the exhibit. Which interface will be the exit interface to forward a data packet with the destination IP address 172.16.0.66?
- ASerial0/0/0
- BGigabitEthernet0/1
- CGigabitEthernet0/0
- DSerial0/0/1
73Refer to the exhibit. Consider that the main power has just been restored. PC3 issues a broadcast IPv4 DHCP request. To which port will SW1 forward this request?
- Ato Fa0/1, Fa0/2, Fa0/3, and Fa0/4
- Bto Fa0/1 and Fa0/2 only
- Cto Fa0/1 only
- Dto Fa0/1, Fa0/2, and Fa0/3 only
- Eto Fa0/1, Fa0/2, and Fa0/4 only
74A network designer must provide a rationale to a customer for a design which will move an enterprise from a flat network topology to a hierarchical network topology. Which two features of the hierarchical design make it the better choice? (Choose two.)
- Asimpler deployment for additional switch equipment
- Bless required equipment to provide the same performance levels
- Ceasier to provide redundant links to ensure higher availability
- Dreduced cost for equipment and user training
- Elower bandwidth requirements
75What is a collapsed core in a network design?
- Aa combination of the functionality of the access, distribution, and core layers
- Ba combination of the functionality of the access and core layers
- Ca combination of the functionality of the distribution and core layers
- Da combination of the functionality of the access and distribution layers
76 What is a definition of a two-tier LAN network design?
- Aaccess, distribution, and core layers collapsed into one tier, with a separate backbone layer
- Bdistribution and core layers collapsed into one tier, and the access layer on a separate tier
- Caccess and distribution layers collapsed into one tier, and the core layer on a separate tier
- Daccess and core layers collapsed into one tier, and the distribution layer on a separate tier
77What is a basic function of the Cisco Borderless Architecture distribution layer?
- Aproviding access to end user devices
- Baggregating Layer 3 routing boundaries
- Caggregating all the campus blocks
- Dacting as a backbone
78Which two previously independent technologies should a network administrator attempt to combine after choosing to upgrade to a converged network infrastructure? (Choose two.)
- Aelectrical system
- Bmobile cell phone traffic
- Cscanners and printers
- DVoIP phone traffic
- Euser data traffic
79A local law firm is redesigning the company network so that all 20 employees can be connected to a LAN and to the Internet. The law firm would prefer a low cost and easy solution for the project. What type of switch should be selected?
- AStackWise
- BStackPower
- Cstackable configuration
- Dmodular configuration
- Efixed configuration
80What are two advantages of modular switches over fixed-configuration switches? (Choose two.)
- Aavailability of multiple ports for bandwidth aggregation
- Bneed for fewer power outlets
- Clower forwarding rates
- Dincreased scalability
- Elower cost per switch
81Which type of address does a switch use to build the MAC address table?
- Asource MAC address
- Bdestination MAC address
- Csource IP address
- Ddestination IP address
82Which network device can be used to eliminate collisions on an Ethernet network?
- Aswitch
- Brouter
- Chub
- Dfirewall
83What two criteria are used by a Cisco LAN switch to decide how to forward Ethernet frames? (Choose two.)
- Adestination MAC address
- Bdestination IP address
- Cingress port
- Degress port
- Epath cost
84What is one function of a Layer 2 switch?
- Adetermines which interface is used to forward a frame based on the destination MAC address
- Blearns the port assigned to a host by examining the destination MAC address
- Cduplicates the electrical signal of each frame to every port
- Dforwards data based on logical addressing
85Refer to the exhibit. How is a frame sent from PCA forwarded to PCC if the MAC address table on switch SW1 is empty?
- ASW1 floods the frame on all ports on the switch, excluding the interconnected port to switch SW2 and the port through which the frame entered the switch.
- BSW1 drops the frame because it does not know the destination MAC address.
- CSW1 forwards the frame directly to SW2. SW2 floods the frame to all ports connected to SW2, excluding the port through which the frame entered the switch.
- DSW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.
86A small publishing company has a network design such that when a broadcast is sent on the LAN, 200 devices receive the transmitted broadcast. How can the network administrator reduce the number of devices that receive broadcast traffic?
- AReplace at least half of the switches with hubs to reduce the size of the broadcast domain.
- BSegment the LAN into smaller LANs and route between them.
- CReplace the switches with switches that have more ports per switch. This will allow more devices on a particular switch.
- DAdd more switches so that fewer devices are on a particular switch.
87Refer to the exhibit. How many broadcast domains are displayed?
- A1
- B55
- C16
- D8
- E4
88Which solution would help a college alleviate network congestion due to collisions?
- Aa router with three Ethernet ports
- Ba router with two Ethernet ports
- Ca high port density switch
- Da firewall that connects to two Internet providers
89Which network device can serve as a boundary to divide a Layer 2 broadcast domain?
- Aaccess point
- BEthernet hub
- CEthernet bridge
- Drouter
90What is the destination address in the header of a broadcast frame?
- AFF-FF-FF-FF-FF-FF
- B11-11-11-11-11-11
- C255.255.255.255
- D0.0.0.0
91Which statement describes a result after multiple Cisco LAN switches are interconnected?
- AThere is one broadcast domain and one collision domain per switch.
- BFrame collisions increase on the segments connecting the switches.
- COne collision domain exists per switch.
- DThe broadcast domain expands to all switches.
92What does the term “port density” represent for an Ethernet switch?
- Athe speed of each port
- Bthe numbers of hosts that are connected to each switch port
- Cthe number of available ports
- Dthe memory space that is allocated to each switch port
93What are two reasons a network administrator would segment a network with a Layer 2 switch? (Choose two.)
- Ato isolate ARP request messages from the rest of the network
- Bto isolate traffic between segments
- Cto eliminate virtual circuits
- Dto create more broadcast domains
- Eto enhance user bandwidth
- Fto create fewer collision domains
Información
- Descripción
- CISCO vom Sommersemester 2020 CSDC
- Autor
- Leona W.
- Idioma
- Deutsch
- Visitas
- 504
- Etiquetas
- Valoración
- Aún sin valoraciones Valora este test