Test
Ch. 7 Study Exam
Crea una cuenta gratis para terminar este test
Guarda tu progreso y consulta tu resultado final.
¿Ya tienes cuenta? Inicia sesión
Preguntas del test (13)
1Which of the following is a reason to create VLANs?
- AVLANs provide better security by separating groups of users and their devices and message traffic.
- BVLANs can segment broadcast domains without using a router.
- CVLANs allow you to forward traffic between networks without a router.
- DVLANs can improve performance on hosts, reducing their processing overhead by limiting the broadcast messages and separating traffic types.
2Which protocol is standard for tagged VLANs over trunks?
- AVLAN Trunking Protocol
- B802.1D
- CDynamic Trunking Protocol (DTP)
- D802.1Q
- ENone of the above
3Which VLAN must always be VLAN 1?
- AThe static VLAN
- BThe native VLAN
- CThe default VLAN
- DThe Layer 2 VLAN
4Which command is used to add interfaces to VLAN 5?
- Aswitchport access vlan 5 on each interface
- Bswitchport access vlan 5 in Global Configuration mode, followed by interface range x - y
- Cswitchport access vlan 5 interface range 0 – 24
- DNone of the above
5Which command(s) can be used to view VLAN membership for all VLANs on the switch?
- Ashow vlan brief
- Bshow membership vlan
- Cshow running-config
- DNone of the above
6Which command is used to add interfaces to VLAN 5?
- Aswitchport mode trunk vlans All
- Bswitchport mode trunk in Global Configuration mode
- Cswitchport mode trunk on each interface
- DNone of the above
7Which command(s) can be used to verify your trunk configuration?
- Ashow vlan brief
- Bshow interfaces type/number switchport
- Cshow interface trunk
- DNone of the above
8Which three are ways to protect unused switch ports?
- AEnter the switchport mode trunk command on each interface
- BEnter the switchport mode access command on each interface.
- CPlace each unused port in a VLAN that does not exist, is inactive, or is connected to limited resources.
- DPlace each unused port in a VLAN 1.
- EDisable each unused interface using the shutdown command.
9Which is not a secure MAC address learning for port security?
- ASticky method
- BRestrict method
- CDynamic method
- DStatic method
10If port security is configured, by default what is the result if a security violation occurs?
- AIt goes into Restrict mode until an admin resets it.
- BIt goes into Restrict mode, denying unsecured MAC addresses but allowing secured MAC addresses.
- CIt goes into Shutdown mode for five minutes (300 seconds) and then resets.
- DIt goes into Shutdown mode until an admin resets it.
- ENone of the above.
11You wish to configure port security on your switch, allowing the switch to learn which MAC address is connected to each port. After setting the interfaces in switchport mode access and turning on port security with switchport port-security, which command should be entered next?
- Aswitchport port-security mac-address
- Bswitchport port-security mac-address address
- Cswitchport port-security mac-address learn
- Dswitchport port-security mac-address sticky
12You have configured port security on all interfaces and entered the following command on the interface range: switchport port-security violation restrict. Which of the following actions will be taken if a foreign MAC address attempts to use an interface?
- AThe interface will be disabled
- BThe offending traffic will be disabled
- CAn SNMP message is sent and logged.
- DThe administrator is notified and decides whether to allow the traffic or not.
13Which command used to verify port security can be used to determine if the port has been disabled by a port security violation?
- Ashow running-config
- Bshow port-security violations
- Cshow port-security interface interface#
- Ddebug mac-address table
Información
- Descripción
- CCENT Information System Test sobre Ch. 7 Study Exam, creado por Darion Ward el 16/05/2017.
- Autor
- Darion Ward
- Idioma
- English
- Visitas
- 4
- Etiquetas
- Valoración
- Aún sin valoraciones Valora este test