Test
Test Review 2
Este test tiene tipos de pregunta que se abren en el reproductor de siempre.
Preguntas del test (32)
1Label the Roof Framing
- ARake or Gable End
- BHip Rafter
- CRidge Board
- DJack Rafter
- ERafter Tails
- FRafter
- GValley Rafter
2Minimum End Bearing of the Rafter or Joist to be at least [blank_start]38mm[blank_end] ([blank_start]1 1/2"[blank_end])
- A38mm
- B1 1/2"
3Hip and Valley Rafters are to be 2" less in depth than the common rafters.
- AVerdadero
- BFalso
4What is the minimum slope required in order to use collar ties.
- A1 in 5
- B1 in 8
- C1 in 3
- D1 in 2
5Pre-Manufactured Trusses are designed to Transfer Loads at the [blank_start]Joints[blank_end] of the Truss.
- AJoints
- BBottom Chord
- CTop Chord
- DStruts
6[blank_start]Wood Blocking[blank_end] can be added to a misfit truss to Ensure that the load is transferred to the load bearing wall.
- AWood Blocking
7When installing Roofing Sheathing how much of a gap should be between sheets.
- A0mm
- B2mm
- C10mm
- D6mm
8A Building Roof is designed to Transfer Loads from Roof Truss to the Bottom Chord
- AVerdadero
- BFalso
9One of the functions of a buildings roof is to shed rain and snow away from the building
- AVerdadero
- BFalso
10Air Barriers should be installed on the warm side of the [blank_start]dewpoint[blank_end]
- Adewpoint
11Which way does Heat Travel
- AWarm to Cold
- BCold to Warm
- CThrough the Wall
- DInterior to Exterior
12Conduction occurs through a [blank_start]Solid[blank_end]
- ASolid
13Convection occurs as [blank_start]heated[blank_end] air becomes less [blank_start]dense[blank_end] and rises, and [blank_start]cold[blank_end] air is drawn into the space left my displaced air
- Aheated
- Bdense
- Ccold
- Dfalls
- Eloose
14Radiation occurs in the [blank_start]absence[blank_end] of a materials
- Aabsence
15Are parts Insulated or Non-Insulated
- AInsulated
- BInsulated
- CNon-Insulated
- DNon-Insulated
- EInsulated
- FInsulated
- GNon-Insulated
16Insulation can be a Max. [blank_start]15"[blank_end] A.F.F. in a basement
- A15"
17In zone 1 what is the min. Required R-Value of Exterior Walls
- AR-15
- BR-24
- CR-35
- DR-20
18In a Cathedral Ceiling Situation is the required attic R-Value allowed to be Lower than in a typical attic situation.
- AVerdadero
- BFalso
19Which of the following are common types of insulation
- ABatt Insulation
- BEarth Insulation
- CBoard Insulation
- DSprayed Insulation
- EStraw Bales
20Does the effectiveness of batt insulation increase when it is installed tightly into cavity (2 batts in one space)
- AVerdadero
- BFalso
21Installing [blank_start]Board[blank_end] insulation on the exterior of a stud wall can decrease thermal bridging by [blank_start]20%[blank_end]
- A20%
- BBoard
22The Purpose of an Air Barrier
- APrevent Exterior Air from entering the Building
- BPrevent air movement under differential air pressure
- CKeep Dust from Insulation out of the House
23Air Barrier must be overlapped by [blank_start]100mm[blank_end]
- A100mm
24A Buildings Roof must fulfill the following requirements
1. [blank_start]Transfer Wind & Snow Loads[blank_end]
2. [blank_start]Shed Rain & Snow Loads[blank_end]
3. [blank_start]Provide for removal of Heat & Moisture[blank_end]
4. [blank_start]Restrict flow of Air, Heat & Mositure[blank_end]- ATransfer Wind & Snow Loads
- BProvide for removal of Heat & Moisture
- CRestrict flow of Air, Heat & Mositure
- DShed Rain & Snow Loads
25What is the maximum clear span of a Roofing Member (in meters)
- A13.0
- B12.2
- C8.0
- D11.0
26A Roof is required to be braced or sheathed on all sides.
- AVerdadero
- BFalso
27What is the minimum OBC roof venting requirement.
- A1/150
- B1/110
- C1/400
- D1/300
28When is Eave Protection Required
- AOver Unheated Garage
- BRoof extends >900mm (2'-11") from Ext. Wall
- C<1:3 slope (with requirement)
- DAll of the Above
29Insulation, Air Barriers, & Vapour Barriers must be designed and installed to fulfill the following requirements...
1. Provide insulation [blank_start]appropriate to the region[blank_end]
2. Restrict [blank_start]Air flow into Bldg Envelope[blank_end]
3. Restrict [blank_start]Water Vapour into Bldg Envelope[blank_end]
4. Allow [blank_start]bldg to breathe to Exterior[blank_end]- Aappropriate to the region
- BAir flow into Bldg Envelope
- CWater Vapour into Bldg Envelope
- Dbldg to breathe to Exterior
30The Primary objective of Insulation is to [blank_start]reduce the overall rate of heat flow[blank_end].
- Areduce the overall rate of heat flow
31Flexible Batt Insulation is typically made of...
- AHay
- BGlass Fibre
- CMineral Wool
- DEarth
32Which of the following are types of Sprayed Insulation
- ACellulose
- BBlue
- CIsocyanurate Foam
- DPolyurethane Foam
Información
- Descripción
- Mid-Term MATS-3010 Test sobre Test Review 2, creado por Olivia Papple el 03/08/2016.
- Autor
- Olivia Papple
- Idioma
- English
- Visitas
- 0
- Etiquetas
- Valoración
- Aún sin valoraciones Valora este test