Test
Switching Midterm Chapters 4, 5, & 6
Este test tiene tipos de pregunta que se abren en el reproductor de siempre.
Preguntas del test (39)
1Which command enables RSTP on a switch?
- Aspanning-tree mode rapid-pvst
- Bno spanning-tree mode pvst
- Cspanning-tree mode rstp
- Drapid spanning-tree enable
2When a switch running RSTP receives an 802.1D BPDU, what happens?
- AThe switch disables RSTP.
- BThe switch begins to use 802.1D rules on that port.
- CBPDU is discarded.
- D802.1D BPDU is translated into 802.1w BPDU and processed.
3Which of the following is an STP port state but not an RSTP port state?
- AForwarding
- BLearning
- CListening
- DDiscarding
4Why is it important to protect the placement of the root bridge?
- ATo prevent Layer 2 loops
- BTo keep Layer 2 topology predictable in such a way that traffic flows are always efficient
- CTo prevent two switches becoming root bridges
- DTo prevent Layer 3 loops
5Can PortFast be configured on a trunk link?
- ANo, PortFast is disabled by the command switchport mode trunk.
- BYes, enabling PortFast globally applies PortFast to all ports, including trunks.
- CYes, it can be configured on a port-to-port basis, but with caution, because loops may occur.
- DNo, the portfast keyword is available only with the switchport mode access command.
6Which two statements are true of Loop Guard?
- AIt allows a blocked port in a physically redundant topology to stop receiving BPDUs.
- BIt provides additional protection against Layer 2 STP loops.
- CIt moves ports into the STP loop-inconsistent state, if BPDUs are not received on a
nondesignated port. - DIt enables the blocking port to move to the forwarding state.
7Which standard describes Multiple Spanning Tree protocol?
- A802.1s
- B802.1D
- C802.1w
- D802.1Q
8Which two features apply to MST?
- AIt groups a set of instances to a single VLAN.
- BIt can group a set of VLANs to a single spanning-tree instance.
- CA failure in one instance can cause a failure in another instance.
- DThe total number of spanning-tree instances should match the number of redundant switch
paths.
9How are VLANs mapped to instances by default with MST?
- AAll VLANs are mapped to MST instance 0.
- BAll VLANs are mapped to MST instance 1.
- CEach VLAN is mapped to its own instance.
- DAll VLANs are unmapped.
10An SVI is a physical Layer 3 interface, whereas a routed port is a virtual Layer 3 interface.
- AVerdadero
- BFalso
11Multilayer switches generally outperform routers of multiple Ethernet interfaces.
- AVerdadero
- BFalso
12A router can forward DHCP requests across VLAN or IP subnet boundaries by using the DHCP relay agent feature.
- AVerdadero
- BFalso
13Based on the example, can the hosts that reside in VLAN 20 communicate with hosts on VLAN 10 if their default gateway is set to 10.2.1.1?

- AYes, if the hosts on VLAN 10 have their default gateway set to 10.1.1.1.
- BNo, the default gateway of the hosts that reside in VLAN 20 should be set to 10.1.1.1.
- CYes, but there is no need to define default gateways.
- DNo, because the routing protocol or static routes are not defined.
14Based on the example, if the hosts that reside on VLAN 10 have their default gateway defined as 10.1.1.1 and ICMP can ping 10.2.1.1 but not a host that resides in VLAN 20, what could be a possible reason?

- AHosts on VLAN 10 are not configured with the correct default gateway.
- BHosts on VLAN 20 are not configured with the correct default gateway.
- CThe routing protocol or static routes are not defined on the Layer 3 switch.
- DVLAN 20 is not defined in the switch database.
15When performing router-on-a-stick inter-VLAN routing, a router interface is subdivided into what?
- AVLAN subinterfaces
- B802.1Q subinterfaces
- CLayer 3 subinterfaces
- DEtherChannel subinterfaces
16Which two commands should be used to configure a router and switch to identify VLAN 10 as the native VLAN on an 802.1Q trunk link? (Choose two.)
- Aencapsulation dot1q vlan 10 native
- Bencapsulation dot1q 10 native
- Cencapsulation dot1q native vlan 10
- Dswitchport trunk dot1q native vlan 10
- Eswitchport mode trunk dot1q vlan 10 native
- Fswitchport trunk native vlan 10
17Place the following five items in the proper order of processing.
[blank_start]1[blank_end]. If necessary, an input router ACL check is performed.
[blank_start]2[blank_end]. The Layer 2 and Layer 3 header are rewritten.
[blank_start]3[blank_end]. The Layer 2 forwarding engine forwards the frame.
[blank_start]4[blank_end]. The Layer 2 engine performs the input VLAN ACL lookup.
[blank_start]5[blank_end]. The dest- A1
- B2
- C3
- D4
- E5
- F1
- G2
- H3
- I4
- J5
- K1
- L2
- M3
- N4
- O5
- P1
- Q2
- R3
- S4
- T5
- U1
- V2
- W3
- X4
- Y5
18Which of the following are not reasons for configuring an SVI? (Choose two.)
- ATo provide fallback bridging if it is required for nonroutable protocols
- BTo provide Layer 3 IP connectivity to the switch
- CTo provide failover if the primary SVI for a VLAN fails
- DTo provide a gateway for a VLAN so that traffic can be routed into or out of that VLAN
- ETo provide connectivity to an external router for inter-VLAN routing
19On which of the following ports would a network engineer be most likely to use the autostate exclude command?
- AAn 802.1Q trunk port connected to an external router
- BA monitoring port connected to an intrusion prevention sensor
- CThe secondary SVI for a VLAN
- DA routed interface on a multilayer switch
- EAll of these answers are correct
20How is a port on a multilayer switch configured as a routed port?
- ABy configuring an IP address and subnet mask on the port
- BBy using the command switchport mode routed
- CBy removing the Layer 2 switching capability of the switch port
- DBy using the command no switchport mode
21When must the command ip routing be used when configuring SVIs on a multilayer switch?
- AWhen an SVI is being used to provide IP connectivity to the switch itself for a given VLAN.
- BWhen the SVI is being configured as part of a Layer 2 EtherChannel bundle.
- CWhen EIGRP is not being used as a routing protocol.
- DWhen an SVI is being used to provide Layer 3 IP forwarding services to its assigned VLAN.
- ENever; IP routing is enabled by default on a multilayer switch.
22What command is used on Cisco IOS switches to change the interface from a Layer 3 interface to
a Layer 2 interface?- Aswitchport mode access
- Bip routing
- Cswitchport
- Dswitchport mode trunk
23Which Cisco IOS command enables IP routing on a Catalyst switch?
- Aip routing
- Binterface <vlan-id>
- Cip address <n.n.n.n> <mask>
- Drouter <ip-routing-protocol>
24Which of the following UDP protocols are forwarded in addition to DHCP when a Layer 3
interface is configured with the ip helper-address command? (Choose all that apply.)- AMobile IP
- BDNS
- CTime
- DFTP
25Which of the following arrangements can be considered “router-on-a-stick”?
- AOne switch, two VLANs, one connection to a router.
- BOne switch, two VLANs, two connections to a router.
- CTwo switches, two VLANs, two connections to a router.
- DAll of these answers are correct.
26Which two statements are typical characteristics of VLAN arrangements? (Choose two.)
- AA new switch has no VLANs configured.
- BConnectivity between VLANs requires a Layer 3 device.
- CEach VLAN usually uses a separate address space.
- DVLANs cannot span multiple switches.
27How do you configure a trunk on a router’s interface that will have connections to more than one VLAN?
- AUse subinterfaces on a physical interface, for each VLAN.
- BUse the switchport mode trunk command.
- CYou do not need to explicitly configure a trunk on an interface.
- DUse the no switchport command.
28You have configured a switch to perform Layer 3 routing via an SVI and have assigned that interface to VLAN 20. To check the status of the SVI, you issue the show interfaces vlan 20 command. You see from the output display that the interface is in an up/up state. Among others, what must be true in an SVI configuration to bring the VLAN and line protocol up?
- AThe port must be physically connected to another Layer 3 device.
- BAt least one port in VLAN 20 must be active.
- CBecause this is a virtual interface, the operational status will always be in an up/up state.
- DAll of these answers are correct.
29While configuring SVIs on a multilayer switch, when must you use the ip routing command?
- AWhen using an SVI to provide IP connectivity to the switch itself for a given VLAN.
- BWhen configuring the SVI as part of a Layer 2 EtherChannel bundle.
- CWhen using an SVI to provide Layer 3 IP forwarding services to its assigned VLAN.
- DNever, because IP routing is enabled by default on a multilayer switch.
30In Layer 3 EtherChannel two links were bundled. On each of the two switches, there are two IP addresses configured.
- AVerdadero
- BFalso
31Which command enables HSRP on a Cisco IOS device?
- Astandby virtual ip 10.1.1.1
- Bstandby ip 10.1.1.1 group 1
- Chsrp 1 ip 10.1.1.1
- Dstandby 1 ip 10.1.1.1
32Which HSRP group uses the MAC address 0000.0c07.ac01?
- AGroup 0
- BGroup 7
- CGroup 11
- DGroup 1
33If you have four routers enabled for the same HSRP group, how many of them will be in standby state?
- A0
- B1
- C2
- DAll, except the active router
34Which VRRP group uses the MAC address 0000.5e00.01ff?
- AGroup 0
- BGroup 1
- CGroup 255
- DGroup 94
35What is the primary difference between VRRP and HSRP?
- AHSRP is a standard protocol, whereas VRRP is Cisco proprietary.
- BVRRP is a standard protocol, whereas HSRP is Cisco proprietary.
- CHSRP is configured at the global level, whereas VRRP is configured at the interface level.
- DVRRP offers Layer 2 first-hop redundancy, whereas HSRP offers Layer 3 first-hop redundancy.
36Which IP address should a client PC use as its default gateway if you have the following configuration on a multilayer switch?

- A192.168.199.1
- B192.168.199.2
- C192.168.199.3
- DAny of the above
37By default, which MAC address will be sent to the next client that is asking for the GLBP virtual gateway?
- A0007.a400.0102
- BNext virtual MAC in sequence
- CVirtual MAC of the least-used router
- DVirtual MAC address of HSRP
38At a maximum, how many active virtual forwarders can be there within a GLBP group?
- A1
- B2
- C4
- D8
39Which of the following best describes the GLBP standby virtual gateway state?
- AThe virtual IP address has not been configured or learned, but there is some GLBP
configuration. - BThe virtual IP address has been configured or learned, but configuration is not complete. The
interface must be operational on Layer 3 and configured to route IP. - CThe virtual gateway is receiving hello packets. It is ready to change to speak state if the active
or standby virtual gateway becomes unavailable. - DThe virtual gateway is trying to become the active or standby virtual gateway.
- EThis gateway is next in line to be the active virtual gateway.
- AThe virtual IP address has not been configured or learned, but there is some GLBP
Información
- Descripción
- Test sobre Switching Midterm Chapters 4, 5, & 6, creado por Ian Organ el 09/02/2017.
- Autor
- Ian Organ
- Idioma
- English
- Visitas
- 11
- Valoración
- Aún sin valoraciones Valora este test