Fichas
Materials

Fichas del conjunto (27)
- 1What are tensile forces?Forces that produce extension
- 2What are compressive forces?Forces that shorten and object
- 3What happens when a tensile force is exerted on a helical spring?Tensile deformation
- 4Draw and label a force-extension graph for a spring

- 5What occurs initially in the tensile deformation of a spring?Elastic deformation (spring will return to its oringinal shape when force is removed) - obeys Hooke's law
- 6What occurs after the elastic deformation of a spring when tensile stress is added to it?Plastic deformation (permanent structural changes to the spring occur) - force-extension correlation does not obey Hooke's law
- 7State Hooke's lawThe extension of the spring is directly proportional to the force applied. This is true as long as the elastic limit of the spring is not exceeded
- 8What is the equation for Hooke's law?F = kx, where k is the force constant
- 9How can you determine the force constant for a material that obeys Hooke's law?Plotting a force-extension graph for the material and finding the gradient from the linear region
- 10Describe an experiment to investigate Hooke's lawAttach a spring to a clamp stand, letting it suspend freely. Measure the length of the spring with a meter ruler. Suspend a force from the spring and determine the extension by taking the original length of the spring from the new length. Keep adding masses and measuring the extension until plastic deformation begins to occur. Plot the results on a force-extension graph.
- 11What happens to work done on a material that has experienced elastic deformation?It is fully recovered
- 12What happens to work done on a material that has experienced plastic deformation?Some of it goes into moving atoms into new permanent positions, which is not recoverable energy
- 13How can you determine the energy stored in an elastic material?Plot a force-extension graph for the material - the area under this graph is the work done on the spring
- 14What is the work done on a spring transferred to during its elastic deformation?Elastic potential energy - this energy is fully recoverable
- 15Derive an equation for elastic potential energy for a spring.E = area under force-extension graph
E = 1/2F - 16What happens to energy stored in a spring if extension doubles?E ∝
- 17Draw and label a force-extension graph for the loading and unloading of a metal wireUnloading graph parallel to loading but further to the right as the wire is permanently extended

- 18Draw and label a force-extension graph for the loading and unloading of a rubber band.The rubber band does not obey Hooke's law. Loading and unloading graphs are curved. The loop formed by the two graphs is a hysteresis loop. Thermal energy lost in the loading of the rubber band is the area inside the loop.

- 19Draw and label a force-extension graph for the loading and unloading of polythene.Polythene does not obey Hooke's law.

- 20Define tensile stressThe force applied per unit cross-sectional area of a material
tensile stress = force / cross-sectional area - 21Define tensile strainThe fractional change in the original length of a material
tensile strain = extension / original length - 22Label this stress-strain graph for a ductile metalA = the limit of proportionality - the material obeys Hooke's law up to this point
B = elastic limit - elastic deformation stops at this point and plastic deformation begins.
y = yield point - where the material extends rapidly
u = the material's ultimate tensile strength - the maximum stress that the material can withstand before it breaks, it may start necking where the material becomes longer and thinner at its weakest point
f = breaking point
- 23What is the equation for the Young Modulus?= tensile stress / tensile strain
- 24What is the Young Modulus?It is the ratio of stress to strain for a particular material, it is a constant for all types of the same material, eg. a block of copper and a thin wire of copper
- 25Describe how you would determine the Young Modulus of a wireClamp a length of wire securely to one end of a table, on the other end pass the wire over a pulley and suspend masses freely at the end of it. Wear eye protection in case the wire breaks. Measure the original length of the wire and then begin to add masses. Measure the diameter with a micrometer and extension with a ruler for each mass added. Use measured diameters to find cross-sectional areas and determine the stress and strain from the results. Plot a stress-strain graph, and determine the gradient.
- 26What would a stress-strain graph for brittle materials look like?Elastic deformation until breaking point - no plastic deformation

- 27—
Información
- Descripción
- AS - Level Physics Fichas sobre Materials, creado por Kayla Price el 31/03/2016.
- Creado por
- Kayla Price
- Visitas
- 0
- Valoración
Más sobre Stress, Strain and Young's Modulus