Flashcards
Engineering Gauntlet
Flashcards do conjunto (61)
- 1—Cap Allen Screw
Designed to be tightened or loosened with an Allen key.
(Stainless) Steel - 2—Castle Nut
Used with a screw in applications where vibrations could undo the fixing as they also use a pin to hold them in place.
(Stainless) Steel
- 3—Centre Drill
Create an accurate centre hole.
High-Speed Steel
- 4—Counterbore Drill
Used to create a flat bottomed hole, which usually has a wide top. Typically used when a fastener needs to sit flush with (or below) the surface of the work piece.
Solid Carbide
- 5—Extension Spring
Create a resistance to a pulling force, they work by trying to pull two objects towards each other.
Steel wire
- 6—External Circlip
They're used as a type of fastener that is designed to fit tightly around a shaft.
(Stainless) Steel
- 7—Flat Blade Screwdriver
Used to tighten or loosen single-slotted screws.
(Stainless) Steel
- 8—Hexagonal Bolt
Primary use is heavy-duty fixing and fastening applications (such as machinery assemblies). They are used for fastening wood, metal, and other materials.
Steel
- 9—Hexagonal Screw
Used to secure an object against or withing another object. They're tightened with a spanner.
Stainless Steel
- 10—Jubilee Clip
A common type of clip fastener, often used to attach a length of tubing or hose pipe firmly onto a suitable fixture.
Stainless Steel
- 11—Needle File
Used to design or finish small pieces of material.
High-Carbon Steel
- 12—Nyloc Nut
A nut with a nylon component that has a smaller inside diameter than the actual nut, which locks it firmly around the bolt when tightened. This prevents the nut from loosening under vibration.
Nylon and Steel
- 13—Plain Washer
Used to evenly distribute the load of the threaded fastener with which they are used.
Steel
- 14—Split Pin
Used to secure a bolt or any other rod-shaped fastener in place. They prevent the bolt from loosening.
Aluminium, Brass, Stainless Steel
- 15—Split Spring Washer
They use friction to prevent bolted joints from loosening. Installed between the bolt head/nut and mating surface, when the nut is tightened, the washer flattens, pushing the sharp edges into the mating surface.
Steel
- 16—Toothed Pulley Wheel
Used with a toothed belt is applications where slipping is unacceptable, mainly for timing mechanisms.
Steel, Aluminium
- 17—Wing Nut
Used as an ordinary nut- to hold two or more objects together when used in conjunction with a bolt- but they have wings on the sides to make them easier to install and remove by hand.
Steel, Aluminium
- 18—Ball Race
Tracks that allow the balls within ball bearings to glide with little or no friction. A fixed path on which the balls can roll. There is an outer and an inner race that keep the balls contained.
Steel
- 19—Ball Bearing
Used to reduce rotational friction and balances both radial & axial loads. A sliding motion is replaced with low-friction rolling.
Steel
- 20—Adjustable Spanner
Used to tighten and loosen fastenings of all sizes as the inside width of the spanner can be adjusted.
Steel
- 21—Allen Key
Used to tighten or loosen bolts or screws that have a hexagonal cut out/indent in their head.
Steel
- 22—Ball Nose Cutter
Used for milling contoured surfaces, slotting and pocketing.
Steel
- 23—Dial Test Indicator
Used to measure clearances, tolerance, and variation in tolerance of machined parts to ensure accuracy.
- 24—Countersunk Screw
Used when you want a screw that rests flush with the object or surface in which it's inserted. The head of countersunk screws are completely buried.
Steel
- 25—Compression Spring
Used to push back on an applied force or load in order to return to its original position when the force or load is released. They can compress and expand when needed.
Steel Wire
- 26—Compression Fitting
used in plumbing and electrical conduit systems to join two tubes or thin-walled pipes together, or a pipe to a fixture or valve.
Brass
- 27—Bevel Gear
Rotating machine elements used to transmit mechanical power between two intersecting shafts that are either perpendicular or at an angle.
Steel
- 28—Expanding Bolt
Fasteners that expand once inserted into a pre-drilled hole in the material. Used to secure heavy objects.
Steel
- 29—Flange
Used to connect pipe systems with various equipment, valves, and other components. They allow for easier disassembly and improved access to system components in a piping system.
Steel, Cast Iron, Aluminium, Brass
- 30—Die Holder
Used for used for fitting and turning dies when threading, cutting or shaping materials.
Steel
- 31—G Clamp
Used to bind or press two or more objects together to keep them firmly in place. Useful when holding or gluing materials together
Steel, Cast Iron
- 32—Flexible Coupling
Used to transmit torque from one piece of rotating equipment to another, while compensating for a small amount of misalignment.
Stainless Steel, Aluminium
- 33—Grub Screw
Used to secure an item against another item, without the use of a nut.
Steel
- 34—Plane / Journal Bearing
One of the most common types of hydrodynamic bearings, their main use is to support a rotating shaft.
Steel
- 35—Hexagonal Nut
Used in conjunction with bolts, screws, and other externally threaded components, they are used to connect both metal and wood components to prevent tension and movement.
Steel
- 36—Internal Circlip
They are made to fit inside a cylindrical shaft or housing. Used for securing mechanical elements or bearings in bores.
Steel
- 37—Gasket
Used as a static seal between flat surfaces, to seal away any leaks.
Rubber
- 38—Lip Seal
Used to protect lubricated moving parts and they do this by keeping the lubricant inside the bearing, and keeping contamination from dirt or other liquids out.
Rubber
- 39—Keyed Shaft
Used to connect a rotating machine element to a shaft so that they rotate together.
Steel
- 40—Metric Tap
They cut material from a pre-drilled or punched hole, producing threads within the hole that are used in conjunction with a screw or bolt.
Steel
- 41—Machine Reamer
Used for expanding or finishing pre-drilled holes, to give a good finish and an exact dimension.
Steel
- 42—Metric Die
Used to create threads on a cylindrical rods surface to create a screw or bolt.
Steel
- 43—Pop Rivet
A type of blind rivet designed to be installed from one side of a joint. They are a permanent joint that will last and resist vibration, and they don't loosen over time.
Many materials, such as Steel and Al
- 44—Open Ended Spanner
They have an opening the width of the nut or bolt head, and two flat sides which grip opposite sides of a fastener. Used to tighten or loosen fasteners.
Steel
- 45—Phillips / Cross Head Screwdriver
Used to tighten or loosen cross-head screws.
Steel
- 46—O Ring
Used to prevent the unwanted escape of gases or liquids. They sit in the joint between these two parts, and become compressed in order to help form a tight seal.
An elastomer, such as Neoprene (rubber)
- 47—Nylon Bush
They are plain bearings which don't need external lubrication and has low friction. They also are quiet in operation, and resist abrasion.
Nylon
- 48—Raw Plug
Used to ensure screws driven into masonry walls have a secure fixing. Without them, screws would not grip into the wall and wouldn't have an adequate compressive force to ensure a secure, permanent fixing.
Plastic
- 49—Ratchet Socket
Attached to a ratchet, and used mostly for loosening and tightening fasteners such as nuts and bolts.
Steel
- 50—Push Fitting
A type of easily removed compression fitting or quick connect fitting that allows an air or water line to be attached. The pipe is just pushed into the fitting to be secured.
Steel
- 51—R Clip
Used to secure the ends of round shafts such as axles and clevis pins. The straight leg is pushed into a hole near one end of the shaft until the semicircular part grips one side, resisting any force removing it.
Stainless Steel
- 52—Pulley Wheel
A wheel that rotates and carries a flexible rope, cord, cable, chain, or belt on its rim. Used on their own or in combination to transmit energy and motion.
Steel, Plastics
- 53—Star Washer
A specific type of washer designed to increase locking force by resisting torque applied by the nut, preventing it from unscrewing or separating.
Steel
- 54—Tap Wrench
A hand tool used to turn taps to create internal threading.
Steel
- 55—Spur Gear
Used in mechanical applications to increase or decrease the speed of a device or multiply torque by transmitting motion and power from one shaft to another through a series of mated gears.
Steel
- 56—Slot Drill
Used for cutting slots, it can also be used in the central part of the application to drill a simple hole.
Steel
- 57—Ring Spanner
Used to tighten or loosen nuts or bolts, slip the ring around the nut or bolt and turn it.
Steel
- 58—V Belt
Used for power transmission. Their primary function is to transmit power from a primary source, a driving unit, to a secondary driven unit.
Rubber
- 59—Yorkshire Fitting
A pre-soldered connector used to join pipework for water, oil and gas systems and are not demountable. They have a ring of solder already inside each end of the fitting.
Copper
- 60—Two-Part Epoxy
A two-part adhesive that is used to glue things (materials, components, etc) together when mixed.
Resin and Hardener
- 61—Twist Drill
Used for drilling holes in lots of different materials (e.g. wood, metal, plastic), they are the most commonly used type of drill bit.
Steel
Informações
- Descrição
- Year 1 ENGG114 FlashCards sobre Engineering Gauntlet, criado por Megan Speight em 23-02-2022.
- Criado por
- Megan Speight
- Visualizações
- 2
- Avaliação