Copy and Edit

01. L01 (unidad 1 profesor)

Description

Tema 1 Avionics Quiz on 01. L01 (unidad 1 profesor), created by Jose Antonio Vazquez on 04/03/2018.
Jose Antonio Vazquez
Quiz by Jose Antonio Vazquez, updated more than 1 year ago
Jose Antonio Vazquez
Created by Jose Antonio Vazquez about 6 years ago
98
5
0

Resource summary

Question 1

Question
Q1. It is not a function of the airframe
Answer
  • Transmit the loads
  • Allow the taxiing of the aircraft in the airport
  • Provide the aerodynamic configuration in every flight condition
  • Protect the payload from the environmental conditions

Question 2

Question
Q2. The use of biplanes at the beginning of the aviation was due to
Answer
  • Structural considerations
  • Aerodynamic considerations
  • A and B are true
  • A and B are false

Question 3

Question
Q3. The failure of the Langley flight in 1903 was a consequence of
Answer
  • A defect of velocity to generate enough lift force
  • A lack of wing stiffness
  • A wrong aerodynamic wing design
  • The interference between the front and rear wings

Question 4

Question
Q4. The buckling is a phenomenon that appear in (i) structures subjected to (ii) loads
Answer
  • (i) wide (ii) tension
  • (i) wide (ii) compression
  • (i) thin (ii) tension
  • (i) thin (ii) compression

Question 5

Question
Q1. What does the AXIAL STRESS consist on?
Answer
  • It occurs when the aircraft is pressurised and the pressure hull lengthens.
  • Stress raised in a container when it is filled, where the contents act to expand the container.
  • It occurs when an structure is subject to several different loads.
  • It produces Stress Cracks due to tension and compression.

Question 6

Question
Q2. The factor that doesn’t affect creep (elongation) is:
Answer
  • Material type
  • Temperature applied
  • Duration of the load
  • Type of object that produces it

Question 7

Question
Q3. Which of the following events does not produce SHOCK LOADS?
Answer
  • Bird strike directly on to the compressor blades of a jet engine
  • Heavy landing
  • Old rubber band stretches and then fails before the normal load is applied
  • High intensity wind gust

Question 8

Question
Q4. What is DESIGN LIMIT LOAD OR DLL
Answer
  • This is the maximum load that the aircraft designer or component manufacturer expects the airframe or component to be subject to in operation.
  • After the aircraft has been subject to this load, there may be permanent deformation of the aircraft’s structure, but it must not collapse.
  • Is equal to the safety factor multiplied by 2
  • Load which produces a catastrophic failure

Question 9

Question
Q5. The Safe life is based on:
Answer
  • Landings
  • Pressurisation cycles
  • Calendar time
  • All the above

Question 10

Question
Q6. About FAIL-SAFE STRUCTURE:
Answer
  • Structure safe because one strong takes the entire load.
  • Allows the structure to continue operating normally up to the static ultimate permanently.
  • Damage would be found by luck because the structure does not show any problem.
  • Extra structural items have a weight penalty, and this has led to a change toward designing damage-tolerant structures.

Question 11

Question
Q7. DUL = Design Ultimate Load magnitude order in airplanes is:
Answer
  • X4
  • X5.5
  • X10
  • None of above

Question 12

Question
Q.8 FRAME CONSTRUCTION in airplanes involves the use of mainly:
Answer
  • SEMI-MONOCOQUE STRUCTURES
  • MONOCOQUE STRUCTURES
  • BICOQUE STRUCTURES
  • BULB SHAPE STRUCTURES

Question 13

Question
Q.9 In regard to the pressurization of the plane:
Answer
  • It has a Front Pressure Bulkhead
  • It has a TOP Pressure Bulkhead
  • The plane is completely pressurized to avoid internal forces
  • The Pressure is different depending of the seat that you occupy

Question 14

Question
Q.10.PASSENGER CABIN WINDOWS
Answer
  • Are essential for temperature regulation
  • The higher pressure of the outside can make them break in mid air
  • Are non-FAIL-SAFE STRUCTURE
  • Are points where the structure weakens

Question 15

Question
Q.11 ALUMINUM ALLOYS used in aviation:
Answer
  • 2024
  • 4070
  • 7075
  • A and C are correct

Question 16

Question
Q.12 Which of the COMPONENTS OF WING STRUCTURE has holes to let fuel go throw?
Answer
  • Spars
  • Ribs
  • Stringers
  • Skin

Question 17

Question
Q.13 Which of these resins are used in aviation?
Answer
  • BLU-TACK
  • PTFE
  • A and B are true
  • A and B are false

Question 18

Question
Q.14 Which of the following materials has been introduced in contemporany times into the structure of new airplanes?
Answer
  • Aluminium
  • Steel Phosphate
  • Composites
  • Zinc plus Gold

Question 19

Question
Q.15 According to the shape of fuselages, in which type of fuselage is common to find the area rule?
Answer
  • Subsonic
  • Supersonic
  • Both of them
  • None is correct

Question 20

Question
Q.16 Which are the three spars normally used in a large aircraft?
Answer
  • Front spar, forward spar and main spar
  • Front spar, rear spar and auxiliary spar
  • Forward spar, main spar and auxiliary spar
  • Front spar, forward spar and rear spar

Question 21

Question
Q.17 The torsion box:
Answer
  • Increases the rigidity of the wing and resists the twisting and bending motion
  • Increases the mass of material used during the construction and due to this the weight is increased
  • Is formed between the spars and the stringers
  • Is the best structure to resist the compression forces

Question 22

Question
Q.18 From JAR 23s. Aircraft are categorised into 3 groups:
Answer
  • Normal, fixed wing aircraft and rotatory wing aircraft
  • Normal, utility and aerobatic
  • Normal, aerobatic and fixed wing aircraft
  • Normal, utility and rotatory wing aircraft

Question 23

Question
Q. 19 In combat aircraft the nose and forward fuselage is used to:
Answer
  • place the main intake ducts for engines
  • Minimize the length
  • Place secondary fuel tanks
  • Radar and laser-ranging installations

Question 24

Question
Q.20 According to monocoque structures, choose the right answer:
Answer
  • Are tubes with horizontal armours
  • The skin only supports ground loads
  • Are used in missiles
  • Are easy to design

Question 25

Question
Q.21 Which one is the main structural element that gives longitudinal strength?
Answer
  • Stringers
  • Formers
  • Longerons
  • Frames

Question 26

Question
Q.22 What elements support the pressure loads?
Answer
  • Bulkhead and skin
  • Stringers
  • Longerons
  • Longerons and frames

Question 27

Question
Q.23 The main objective of winglets is:
Answer
  • Delay the critical Mach
  • Increase the stall speed
  • Aesthetic reasons
  • Reduce wing tip vortices
  • Mal porque pone que es Aesthetic reasons

Question 28

Question
Q. 24 According to wing mounted engines:
Answer
  • Engines are joined to the wing structure by a pylon
  • The pylon is attached to the front and mains spars
  • In flight, the weight of the engine balances the aerodynamic loads (lift)
  • All of them are right
Show full summary Hide full summary

Want to create your own Quizzes for free with GoConqr? Learn more.

Similar

1.Test
Jose Antonio Vazquez
5. test
Jose Antonio Vazquez
4. test 4
Jose Antonio Vazquez
7. test
Jose Antonio Vazquez
9. Test
Jose Antonio Vazquez
Limitaciones E-25 C 101
Jose Antonio Vazquez
1.AVIOìN Y MOTOR 235 PROPUESTA SEP12 CON RESPUESTAS (Planta de Potencia)
Jose Antonio Vazquez
2.AVIOìN Y MOTOR 235 SEP09 CON RESPUESTAS (REPASAR)
Jose Antonio Vazquez
2.1AVIOìN Y MOTOR 235 SEP09 CON RESPUESTAS (REPASAR)
Jose Antonio Vazquez
UNIDAD 1 DIBUJO NORMALIZADO
jose ricardo cuero hernandez
ESTRUCTURA DEL ESTADO COLOMBIANO
Juan Barrero
Browse Library