Quiz
RCM quiz
This quiz has question types that open in the usual player.
Questions in this quiz (19)
1Q: What does RCM stand for and write a short summary about the RCM-concept.
A: R[blank_start]eliability[blank_end] C[blank_start]entered[blank_end] M[blank_start]aintenance[blank_end]
A systematic consideration of system functions, the way functions can fail, and a priority-based consideration of safety and economics that identifies applicable and effective PM tasks.- Aeliability
- Bentered
- Caintenance
2What are the general main reasons for doing a PM task?
→ P[blank_start]revent[blank_end] a failure
→ D[blank_start]etect[blank_end] the onset of a failure
→ D[blank_start]iscover[blank_end] a hidden failure- Arevent
- Betect
- Ciscover
3Which five basic maintenance tasks are considered in FMECA?
1. Scheduled [blank_start]on-condition[blank_end] task
2. Scheduled [blank_start]overhaul[blank_end]
3. Scheduled [blank_start]replacement[blank_end]
4. Scheduled [blank_start]function[blank_end] test
5. Run to [blank_start]failure[blank_end]- Aon-condition
- Boverhaul
- Creplacement
- Dfunction
- Efailure
4What are the 3 criteria that must be met for an on-condition task to be applicable?
1. It must be possible to [blank_start]detect[blank_end] reduced failure resistance for a specific failure mode.
2. It must be possible to [blank_start]define[blank_end] a potential failure condition that can be detected by an explicit task.
3. There must be a reasonable consistent [blank_start]age[blank_end] [blank_start]interval[blank_end] between the time of potential failure (P) and the time of functional failure (F- Adetect
- Bdefine
- Cage
- Dinterval
5What is the scheduled overhaul criteria’s (often called “Hard time maintenance”)
1. There must be an identifiable age at which there is a rapid [blank_start]increase[blank_end] in the item’s failure rate function.
2. A large proportion of the units must [blank_start]survive[blank_end] to that age.
3. It must be possible to [blank_start]restore[blank_end] the original failure resistance of the item by reworking it.- Aincrease
- Bsurvive
- Crestore
6What does PM stand for and when is a PM applicable?
P[blank_start]lanned[blank_end] M[blank_start]aintenance[blank_end]
If it can [blank_start]eliminate[blank_end] a failure, or at least [blank_start]reduce[blank_end] the probability of occurrence to an acceptable level- or reduce the impact of failures.- Alanned
- Baintenance
- Celiminate
- Dreduce
7What is cost-effectiveness?
Meaning that the task does not cost more than the failure(s) it is going to prevent.
• The PM task’s effectiveness is a measure of how well it accomplishes that purpose and if it is worth doing.
Clearly, when evaluating the effectiveness of a task, we are balancing the cost of [blank_start]performing[blank_end] the maintenance with the cost of not [blank_start]performing[blank_end] it.- Aperforming
- Bperforming
8Write down the 12 main steps of analysis in RCM
1. [blank_start]Study preparation[blank_end]- AStudy preparation
9Write down the 12 main steps of analysis in RCM
1. S----- ---------
2. S[blank_start]ystem[blank_end] s[blank_start]election[blank_end] and d[blank_start]efinition[blank_end]- Aystem
- Belection
- Cefinition
10Write down the 12 main steps of analysis in RCM
1. S------ ---------
2. S---- -------- and --------
3. [blank_start]Functional[blank_end] [blank_start]failure[blank_end] [blank_start]analysis[blank_end] (FFA)- AFunctional
- Bfailure
- Canalysis
11Write down the 12 main steps of analysis in RCM
1. --------- -----------
2. -------- -------- and ----------
3. ---------- ---------- --------- (FFA)
4. C[blank_start]ritical[blank_end] [blank_start]item[blank_end] [blank_start]selection[blank_end]- Aritical
- Bitem
- Cselection
12Write down the 12 main steps of analysis in RCM
1. ----
2. ----
3. ---- (FFA)
4. ---
5. D[blank_start]ata[blank_end] [blank_start]collection[blank_end] and [blank_start]analysis[blank_end]- Aata
- Bcollection
- Canalysis
13Write down the 12 main steps of analysis in RCM
6. [blank_start]Failure[blank_end] [blank_start]modes[blank_end], [blank_start]effects[blank_end] and [blank_start]criticality[blank_end] [blank_start]analysis[blank_end] (FMECA)- AFailure
- Bmodes
- Ceffects
- Dcriticality
- Eanalysis
14Write down the 12 main steps of analysis in RCM
7. S[blank_start]election[blank_end] of [blank_start]maintenance[blank_end] [blank_start]actions[blank_end]- Aelection
- Bmaintenance
- Cactions
15Write down the 12 main steps of analysis in RCM
8. D[blank_start]etermination[blank_end] of [blank_start]maintenance[blank_end] [blank_start]interval[blank_end]- Aetermination
- Bmaintenance
- Cinterval
16Write down the 12 main steps of analysis in RCM
9. P[blank_start]reventive[blank_end] [blank_start]maintenance[blank_end] [blank_start]comparison[blank_end] [blank_start]analysis[blank_end]- Areventive
- Bmaintenance
- Ccomparison
- Danalysis
17Write down the 12 main steps of analysis in RCM
10. T[blank_start]reatment[blank_end] of [blank_start]noncritical[blank_end] [blank_start]items[blank_end]- Areatment
- Bnoncritical
- Citems
18Write down the 12 main steps of analysis in RCM
11. I[blank_start]mplementation[blank_end]- Amplementation
19Write down the 12 main steps of analysis in RCM
12. In-[blank_start]service[blank_end] [blank_start]data[blank_end] [blank_start]collection[blank_end] and [blank_start]updating[blank_end]- Aservice
- Bdata
- Ccollection
- Dupdating
Information
- Description
- Operations and Maintenance Quiz on RCM quiz, created by Magnus Parmann on 14/03/2018.
- Author
- Magnus Parmann
- Language
- English
- Views
- 18
- Tags
- Rating
- No ratings yet Rate this quiz