Quiz
Sistemas 7
Create a free account to finish this quiz
Save your progress and see your final score.
Already have an account? Sign in
Questions in this quiz (200)
1A differential aileron control system results in.
- Aaileron drag being reduced on the inner wing in a turn.
- Baileron drag being compensated by small rudder movements.
- Caileron drag being reduced on the outer wing in a turn.
2Spoiler panels are controlled by.
- Athe aileron control wheel and speed brake lever.
- Ba speed brake lever only.
- Cthe aileron control wheel only.
3A lift transducer is normally fitted.
- Aon the elevator control system.
- Bto the nose area of the aircraft.
- Con the leading edge of the wing
4"If electrical power is removed from a fly by wire spoiler
system, the spoiler panels."
O- Ago to down if any are not already down.
- Bgo to full up.
- Cremain where they are
5In a fly-by-wire control system, the follow-up transducer is fitted to.
- Athe control system computer.
- Bthe hydraulic actuator.
- Cthe pilots input
6The down position of the speed brake lever is detented to.
- Aprevent inadvertent operation.
- Block the speed brakes down during flight.
- Callow the ground speed brakes to be used on touchdown.
7Asymmetric flap operation is prevented to keep to a minimum the tendancy of.
- Ayawing.
- B rolling.
- Cpitch changes.
8High thrust stall warning is activated when the thrust of opposite engine reads.
- Agreater than 75%.
- Bgreater than 50%.
- Cgreater than 90%
9A differential aileron control is one which gives.
- Aa larger aileron up travel than down.
- Bthe down-going aileron more travel than the up-going one.
- Cequal aileron travel in each direction, but variable for stick movement
10When the control column is moved back and the hand-wheel turned to the left.
- Athe elevators move down and the left aileron moves down.
- Bthe left aileron moves up and the elevators move up.
- Cthe elevators move up and the left aileron moves down.
11A series type yaw damper.
- Amoves the rudder and the ailerons to damp out Dutch roll.
- Bmoves the rudder pedals and the rudder.
- Cmoves the rudder only
12 A stick shaker.
- Ais a linear actuator attached to the base of the control column.
- Bis an eccentric flywheel driven by an electric motor and mounted on the control column.
- Cvibrates the elevators to cause buffeting of the airframe
13If the control column is moved forward and to the left.
- Aleft aileron moves down, right aileron up, elevator down.
- Bleft aileron moves up, right aileron down, elevator down.
- Cleft aileron moves up, right aileron moves down, elevator up
14 On an aircraft fitted with spoilers for lateral control, roll to the right is caused by.
- Aleft spoiler extending, right spoiler remaining retracted.
- Bright spoiler extending, left spoiler remaining retracted.
- Cboth spoilers extending
15When an aileron trim control in the cockpit is moved to counteract a tendency to fly left wing low, an aileron trim tab fitted to the port aileron will.
- Amove up and cause the left aileron to move down but the right aileron will remain neutral.
up - Bmove up and cause the left aileron to move down and the right aileron to move down to a lesser degree.
- Cmove up and this will cause the left aileron to move down and the right aileron to move
- Amove up and cause the left aileron to move down but the right aileron will remain neutral.
16You have adjusted the elevator trim tab to correct for nose heavy. What was the direction of travel of the trim tab?.
- AThe port elevator tab has moved up and starboard moved down.
- BThe elevator trim tab has moved up.
- CThe elevator trim tab has moved down.
17 Pulleys in a flight control system are made from.
- Abrass.
- Bstainless steel.
- CTufnol or aluminium alloy
18A tension regulator in the flight control cable system of a large all metal aircraft is used primarily to.
- Aretain a set tension.
- Bincrease cable tension in cold weather.
- Cdecrease cable tension in cold weather
19An interrupter arm incorporated in a flying control locking mechanism.
- Alocks the ailerons and elevators.
- Brestricts movement of the throttles.
- Cdampens the rudder movement
20The yaw damper must be designed to allow the rudder to control in response to the aircraft's.
- Apitch Frequency.
- Broll frequency.
- Cdutch roll frequency.
21The alpha vane signal can be fed to __________ when the aircraft is close to stall.
- Aflap position.
- Bfast/slow switch.
- Cthrottle lever
22Moving the elevator trim wheel fully aft, then the.
- Aaircraft tends to go nose down.
- Baircraft tends to go nose up.
- Caircraft tends to roll to the right
23Ground spoilers are used to.
- Aincrease wing loading on take-off.
- Bprevent FOD ingestion into the engines on landing and taxiing.
- Cdecrease wing loading on landing
24The outboard ailerons on some aircraft.
- Aare isolated at slow speeds.
- Bare isolated to prevent aileron reversal.
- Care isolated to improve sensitivity.
25The effect of the rudder on an aircraft can be increased by.
- Aincreasing the distance of the control surfaces from the aircraft's centre of gravity.
- Bincreasing the altitude of the aircraft.
- Cdecreasing the velocity of the aircraft.
26A fuel crossfeed valve is usually in.
- Athe closed position.
- Bthe open position.
- Cits last position
27Sliding couplings in fuel systems are used on.
- Alow pressure systems.
- Bhigh pressure systems.
- Cair or vapour systems.
28A fuel cross-feed valve is lubricated.
- Aby internal cooling.
- Bby air.
- Cby the fuel.
29Fuel cross feed valves are operated by the.
- A28 V DC bus.
- B115 V AC.
- Cbattery
30Fuel systems that are interconnected must have.
- Aseparate venting for each tank.
- Bno airspace.
- Cair spaces interconnected
31As fuel level increases, system capacitance.
- Adecreases.
- Bno change.
- Cincreases.
32When refuelling.
- Athe fuel nozzle will automatically cut off the supply when the tank is full.
- Bit is important not to fill the expansion space in the tank.
- Cit is important to fill the expansion space in the tank.
33When using Biopor microbial fuel growth treatment.
- Ait is added to the fuel and burnt.
- Bit is applied dry and left.
- Cit is applied wet and flushed out
34Microbial growth is.
- Ared dots.
- Bbrown black slime.
- Cgreen sludge
35Bladder type fuel tanks are secured by.
- Abolts.
- Bcontact adhesive.
- Cpress type rivets.
36A zero fuel test on a fuel quantity indicating system is carried out with.
- Atanks completely full.
- Btanks completely empty.
- Ctanks empty apart from unusable fuel
37After a tank bag has been replaced, a fuel flow test should be carried out at.
- Atank outlet.
- Bengine inlet.
- Ctank shut-off valve point
38In biologically contaminated fuel, corrosion takes place.
- Abelow the fungal colonies.
- Bthe top of the tank.
- Cthe bottom 2 inches of the tank
39If an aircraft has ability to transfer fuel in flight, provision must be made to.
- Ashut off fuel before structural damage.
- Bprovide overflow facility to dump fuel.
- Cstop engine from using tank during transfer
40In a fuel system with interconnected vents.
- Aan expansion space is not required.
- Bthe expansion space must be 2% of the tank capacity.
- Cthe expansion space must be 10% of the tank capacity
41Fuel tanks interconnected must have.
- Avents to allow overfueling.
- Bprotection against overfill for tanks and fuel system.
- Ctank where fuel is fed from both tanks to engine inlet.
42When a FADEC system loses air data input it goes to.
- Asoft reversion.
- Bhard reversion.
- Cmechanical reversion.
43Pressure refuelling is carried out at.
- A20 PSI.
- B40 PSI.
- C15 PSI
44Cross feed valves permit fuel transfer from.
- Atank to tank.
- Bleft tank to right tank.
- Cany tank to any engine.
45What is fitted to the fuel jettison pipe to prevent vaporisation?.
- AAn anti-corona device.
- BA corona device.
- CA nozzle
46What happens to the capacitance in a fuel contents gauge as fuel is used?.
- ADepends on altitude.
- BIncreases.
- CDecreases
47When an aircraft is put into storage for medium / long periods, the fuel tanks should.
- Ahave some fuel left in to prevent sealant from deteriorating/drying out.
- Bbe full.
- Cbe empty.
48Integral fuel booster pumps.
- Arequire ram air cooling.
- Blets the fuel do cooling.
- Crequire no cooling
49The purpose of a scavenge system within a fuel system is.
- Ato ensure that all unused fuel is returned to the tanks efficiently.
- Bto ensure that all available fuel can be used.
- Cto ensure that any water in the fuel is constantly dispersed thus reducing microbiological contamination.
50In a light fixed wing aircraft, the fuel warning light indicates.
- Apump failure.
- Bthe tank does not pressurise.
- Cice blockage, filter popped or pump fail.
51How is fuel supplied to a turbine engine?.
- ABy a fuel boost pump.
- BBy suction from the engine driven fuel pump.
- CBy a gravity feed pump
52A fuel tank suction valve will open when.
- Athe booster pump fails.
- Bboth the engine driven and booster pump fail.
- Cthe engine driven pump fails.
53To prevent water condensation in a fuel tank.
.- Athe tank should be filled as full as possible.
- Bthe tank should be filled with the minimum fuel possible.
- Cthe filler cap should be left open
54To protect the centre tank fuselage area from a vapour build up.
- Aram air is circulated around the tank.
- Ba shroud vent and overboard drain is fitted.
- Ccabin air is bled around the tank
55When a fuel jettison valve is in transit, the magnetic indicator would show.
- Aamber and in line.
- Bamber and cross line.
- Cgreen and in line
56When considering the basic categories of fuel tank construction, which of the following is most prone to leaks?.
- ARigid.
- BIntegral.
- CFlexible.
57On removal of a fuel tank booster pump, fuel is observed running out of the boost pump canister, this could be caused by.
- Athe pressure outlet check valve is not correctly seated.
- Bfuel draining out of the pressure switch bleed.
- Cfuel leaking past the inlet screens
58Crossfeed valves are normally fitted with.
- Atwo 28V DC motors.
- Btwo three-phase AC motors.
- Ctwo single phase AC motors.
59A shroud vent and overload drain would normally be found on.
- Afuel tank vent pipes.
- Bfuel jettison system.
- Cthe APU fuel feed
60To shut-off the LP fuel supply to the engine for the purpose of engine removal you would.
- Aclose the cross bleed valve.
- Bclose the HP fuel lock.
- Cpull the fire handle.
61A leak from a fuel tank which manifests as fuel dripping from the tank is classified as a.
- Astain.
- Bseep.
- Crun.
62Calcium Chromate tablets can be fitted in integral tanks. Before installation the linen bag should be wetted with.
- AWater.
- BMethylated Spirit.
- C Kerosene
63 A check valve is fitted to a fuel jettison system to.
- Aprevent the centre from being defuelled.
- Bprevent the dumping of the outer tanks.
- Cautomatically stop the fuel jettison operation after a period of time
64The advantages of integral fuel tanks are that they.
- Aare cheaper to manufacture, more durable and easier to maintain.
- Buse the maximum volume for fuel and have the minimum amount of weight.
- Care easier to design and construct and use the maximum volume of fuel.
65On Large transport aircraft fuel is delivered to each engine using.
- Aa parallel system.
- Bthe same system for each engine.
- Ca separate system for each engine.
66 A purpose of a 'cut-out' in a hydraulic system.
- Ais to prevent creep in jack operated services which have several selected positions.
- Bis to limit loss of fluid in the event of pipe fracture.
- Cis to relieve the pump of load when the operation of services is complete and the accumulator charged with fluid.
67Hydraulic pressure can be restored by.
- Acompressing the air charge in an accumulator.
- Bthe use of a pressure/heat exchanger.
- Ccompressing the fluid in a reservoir.
68What is the colour of the band on a hydraulic seal?.
- AYellow.
- BGreen.
- CWhite
69A maintainer valve in an hydraulic system will.
- Aallow continued press to essential systems during times of reduced supply.
- Bdampen pressure inputs.
- Cmaintain a high pressure to all systems
70Where is the temperature overheat switch located in a hydraulic pump?.
- AIn the pressure line.
- BIn the suction line.
- CIn the case drain.
71What happens if a component has an internal hydraulic leak?.
- AFluid loss.
- B Increase in fluid pressure.
- CIncrease in fluid temperature
72What happens to hydraulic fluid when it is overheated?.
- AIncrease acidity.
- BIncrease viscosity.
- CIncrease alkalinity
73How is the hydraulic pump depressurising solenoid actuated?.
- AEnergised both open and closed depending on cockpit selection.
- BEnergised Open.
- CEnergised Closed for fail-safe
74How do you prevent hydraulic fluid frothing?.
- ABy pressurising.
- BVent Reservoir to atmosphere.
- CPass over a tray.
75Accumulators as fitted to aircraft hydraulic systems.
- Aare only ever used in an emergency.
- Bstore fluid under pressure.
- Cprovide additional fluid if leaks occur
76A Skydrol hydraulic fluid seal would be made of.
- Anatural rubber.
- Bsynthetic rubber.
- Cbutyl rubber, ethylene propylene or Teflon.
77Synthetic hydraulic fluid subjected to overheating is high in.
- Aacidity.
- Balkalinity.
- Cviscosity.
78 A normal hydraulic system will.
- Ashow pressure and source of hydraulics.
- Bshow fluid temperature and quantity.
- Cilluminate a light in the cockpit when the system is ready.
79A constant volume hydraulic system uses what to relieve pressure in system when no services are being used?.
- APressure relief valve.
- BReturn line back to pump.
- CACOV
80The control of hydraulically powered emergency electrical generator frequency is by.
- Arestriction valve.
- Bangle of swashplate.
- CIDG
81Hydraulic systems normally operate at.
- A1800 PSI.
- B3000 PSI.
- C300 PSI
82When flushing hydraulic systems.
- Aflush with methylated spirit.
- Bflush with any hydraulic oil.
- Cflush with same hydraulic oil
83When replenishing a hydraulic system.
- Ause any hydraulic fluid.
- Buse any hydraulic fluid made by the same manufacturer.
- Cuse the same/correct hydraulic fluid.
84When replacing a flexible pipe.
- Ado a bonding check.
- Btighten only hand tight.
- Cuse two spanners to stop pipe from twisting.
85How do you remove air from hydraulic fluid?.
- AVent to atmosphere.
- BPass through a restriction.
- CPass over a tray
86 A pressure control relay in a hydraulic pump is.
- Aenergised to the run position.
- Bused to prevent anything happening until there is hydraulic pressure.
- Cde-energised to start the pump
87 A constant delivery pump has its output varied with.
- Aregulators.
- Bgears.
- Cservo pressure.
88A variable angled pump starts at.
- Ahalf way position.
- Bminimum stroke.
- Cmaximum stroke.
89A check flow valve in a hydraulic system prevents.
- Apump cavitation.
- Breverse flow.
- Coverpressure.
90A duplex seal consist of.
- Aa square section rubber ring within a steel washer.
- Ba hard rubber square section ring with a soft rubber square section inner ring.
- Ca rubber 'T' section ring sandwiched between two Teflon rings
91When is an hydraulic de-pressurising valve energised?.
- AWhen selected on.
- BWhen there is sufficient hydraulic pressure available.
- CWhen selected off.
92A fixed volume axial pump contains the following rotating parts.
- ADrive Shaft, Swash Plate & Valve Block.
- BSwash Plate & Valve Block.
- CDrive Shaft, Swash Plate & Cylinder Block
93An hydraulic closed system is one where.
- Apressure is maintained at the selector valves at all times.
- Bthere is no pressure at the selector valves when no functions are required.
- Cmost of the major components of the system are included in a self contained unit
94What constitutes a hydraulic power pack?.
- AVariable swashplate pump.
- BReservoir, pump, selector valve, filter.
- CHydraulic oil accumulator.
95If an accumulator loses air pressure there will be.
- Arapid depressurisation of system.
- Bpump cavitation.
- Crapid fluctuations of instruments
96A marker number on a pipe indicates.
- Athe thickness of the wall on the pipe.
- Bthe specification of the pipe throughout the pipe run.
- Cthe type of fluid used to pressure test the pipe.
97 "One reason for fitting an accumulator in an hydraulic system is
to."- Aminimize the possibility of pump cavitation.
- Babsorb pressure surges.
- Crelieve excess pressure
98A thermal relief valve is fitted to an hydraulic system to.
- Aprevent a leak back of pressure.
- Bprevent excess temperature.
- Crelieve excess pressure
99A component in a hydraulic system which ensures instantaneous action when a service is selected is.
- Aaccumulator.
- Bengine driven pump.
- Cselector
100A shuttle valve is used for.
- Apreventing fluid loss from a leaking jack.
- Bmaintaining fluid press when the emergency system fails.
- Cchange over from main to auxiliary system in the case of failure
101Restrictor valves in an hydraulic system are used to.
- Arestrict the rate of pressure build up.
- Bcontrol the rate of system operation.
- Climit the maximum pressure
102The purpose of a mechanical sequence valve is to ensure the operation of.
- Alanding gear and doors.
- Bsafety switches.
- Cbrake anti-skid units.
103The purpose of a non-return valve is to.
- Adirect fluid to the hydraulic actuator.
- Brestrict the movement of components.
- Cisolate one component from another
104The end fittings on a NRV are normally different to.
- Afacilitate bleeding of the system.
- Ballow a full flow from the valve.
- Cprevent incorrect installation
105A hydraulic accumulator is charged with initial air pressure of 1000 PSI. When the hydraulic system pressure of 3000 PSI is reached, the air pressure is.
- A4000 PSI.
- B3000 PSI.
- C1000 PSI.
106Automatic cut-out valve hammering is caused by.
- Alow accumulator pressure.
- Bmoisture in the fluid.
- Crelief valve set too high
107Hand pumps are normally single cylinder double acting because of the.
- Atwo NRVS fitted.
- Brelief valve.
- Cpiston ram displacement.
108During a leak test of an hydraulic system, system pressure.
- Ais not important.
- Bmust be minimum working.
- Cmust be at maximum.
109Constant delivery hydraulic pumps.
- Arequire an automatic cut-out valve in the system.
- Brequire an automatic cut-out valve and accumulator in the system.
- Care self idling
110Mechanical sequence valves are operated by.
- Aa striker pin.
- Bthe pilot.
- Cthe operation of a NRV
111Pressure relay valves are fitted.
- Abefore a pressure gauge.
- Bbefore a pressure sequence valve.
- Cbefore a pressure relief valve
112Before checking the initial pressure in the hydraulic accumulator.
- Athe reservoir must be checked for correct level.
- Bthe fluid pressure must be released.
- Call air must be bled from the system
113Hydraulic reservoirs are pressurized to.
- Aprovide a reserve of stored energy.
- Bmaintain a constant fluid level.
- Cminimize the possibility of pump cavitation.
114In aircraft hydraulic systems, it is permissible to use.
- Aonly the specified fluid.
- Bany fluid of the same specific gravity.
- Cany hydraulic fluid available.
115The essential components of a hydraulic system of the constant delivery type are an.
- Aaccumulator and automatic cut-out valve.
- Baccumulator and shuttle valve.
- Caccumulator and relay valve
116An automatic cut-out valve will.
- Alimit pump wear.
- Bprevent the hydraulic lock forming.
- Craise fluid boiling point
117A maintaining valve is fitted to a hydraulic system.
- Ato maintain a back pressure to the accumulator.
- Brelieve excessive pressure to return.
- Cto ensure a supply of fluid to essential services in the event of system failure
118A thermal relief valve.
- Asenses fluid temperature change.
- Bsenses fluid pressure.
- Cprovides cooling for the fluid.
119Hydraulic systems are normally flushed with.
- Amethylated spirits.
- Bthe same type of fluid as used in the system.
- Cany clean hydraulic fluid.
120Phosphate Ester hydraulic fluid requires which kind of seals?.
- AButyl Rubber.
- BSynthetic Rubber.
- CNatural Rubber.
121A RAT hydraulic pump is for.
- Alanding gear and auto-brake systems.
- Bnose wheel steering.
- C flying controls if hydraulic power lost
122Hydraulic hand-pump fluid supply is taken from.
- Aa tap into a convenient return line.
- Ba stack pipe higher than the normal level.
- Cthe bottom of the reservoir.
123Hand pumps in hydraulic systems are normally.
- Asingle acting.
- Blow pressure.
- Cdouble acting
124To enable an hydraulic system to operate two components requiring different pressures.
- Aa pressure reducing valve is used.
- Ba pressure regulating valve is used.
- Ca pressure relief valve is used
125The force exerted by a hydraulic cylinder is equal to.
- Aarea * volume.
- Barea * pressure.
- Cpressure * stroke
126A tandem PFCU.
- Ahas two control surfaces under its control.
- Bhas the rams parallel.
- Chas the actuator rams co-axial.
127The reason why slack must be left in a flexible hose during installation, is a flexible hose under pressure.
- Aexpands in length and diameter.
- Bcontracts in length and diameter.
- Ccontracts in length and expands in diameter
128An automatic cut-out valve is necessary in a hydraulic system with.
- Aa fixed volume pump.
- Bpressures above 3000 PSI.
- Ca variable volume pump
129How is a serrated rod ice detector bench tested?.
- AScrewdriver torque test.
- BBy a motor load test.
- CMotor test and go/no-go gap measurement.
130Windshield heating provides.
- Athermal expansion for a tighter fit.
- Bimpact resistance enhancement.
- Cincreases strength to resist cabin pressure
131At what pressure and temperature is anti ice fluid applied?.
- A7°F at 100 PSI.
- B70°C at 100 PSI.
- C70°F at 10 PSI.
132The advantage of leading edge fluid de-icing is.
- Aless of a fire hazard.
- Baerodynamic shape is not disturbed.
- Cmore efficient.
133On large transport aircraft, the windshield wiper system is.
- Aone system for both sides but with the same power source.
- Bindependent on each side but with the same power source.
- Cindependent on each side with different power sources
134Prior to securing a leading edge de-icing boot you must.
- Aremove all paint.
- Bpaint the surface.
- Cshave rivet to prevent further abrasion
135On a 'hot rod' type of ice detector, it is switched on.
- Aall the time.
- Bwhen selected by the crew.
- Cwhen in the air.
136Ice formation on wings is due to.
- Asuspended ice crystals melting on contact with the wing and instantly re-freezing.
- Bice crystals forming layers on contact with the wing.
- Csupercooled water changing state on contact with the wing.
137When a vibrating rod ice detector has de-iced, the warning lamp on the flight deck.
- Agoes out immediately.
- Bgoes out after one more cycle.
- Cgoes out after a set period of time
138De-misting of passenger windows is provided by.
- Asealed window.
- Ban electrical heating element.
- Cair from the cabin.
139A deicer boot is completely bonded to the leading edge to.
- Aprovide smoother airflow over leading edge.
- Bprevent electrical static build up.
- Cprovide more efficient deicer cycles.
140In a cockpit window heater system, the autotransformer.
- Asupplies DC power for heating.
- Bsupplies AC Power for heating.
- Csteps up output for severe weather conditions
141Windshield rain repellent is applied.
- AOwhen rain is on windows and spread by wipers.
- Bbefore rain and spread on window surface by wipers.
- Cwhen in heavy rain so vision is unobscured
142Pneumatic rain removal systems.
- Ause engine bleed air at high velocity to remove water droplets from windscreen.
- Bare not permitted on large transport aircraft.
- Cuse a pneumatic motor to drive windscreen wipers
143Windscreen wiper torque tests are carried out at.
- Ablade attachment end.
- Bcentre point of the blade.
- Cthe shaft end
144Windscreen autotransformers.
- Astep down voltage.
- Bstep up voltage.
- Care used to supply extra current under difficult conditions
145An ice deposit formed when liquid water flows over the airframe before freezing, and which is dense, tough and sticks closely to the surface is called.
- Aglaze Ice.
- Brime Ice.
- Choar Frost
146When testing pitot head heaters.
- Athey can only be checked by noting the temperature rise of the probe.
- Bthey must only be switched on for the minimum time required to check serviceability.
- C they should be switched on for five minutes to allow to stabilise before taking ammeter readings
147A rotary knife edge ice detector provides warning of ice by.
- Aincreased torque caused by ice formation slowing the rotating wheel and illuminating a warning light in the cockpit.
- Bdecreased torque caused by ice formation slowing the rotating wheel and illuminating a warning light in the cockpit.
- Cice formation stopping the rotation of a rotary knife edge and illuminating a warning light in the cockpit
148Windscreen heating is supplied from.
- Afrequency wild generador, direct to the windscreen.
- BDC generator, via a transformer.
- Cfrequency wild generator, via a rectifier.
149A wing thermal anti-ice annunciator is illuminated permanently in flight deck without selection being made. The most probable cause would be.
- Aa short circuit.
- Ban open circuit.
- Cnormal
150Air for anti-icing of the wings is obtained from.
- Aair conditioning ducting.
- Bengine compressors.
- Ca combustion heater.
151The usual material for pipelines in a fluid deice system.
- Astainless steel.
- BMonel.
- Cnylon
152When operating a windscreen wiper on the ground, make sure to.
- Ause slow wiper only.
- Buse water as lubricant when operating.
- Cplace soft cloth between blade and window
153What is run-back ice?.
- AGlaze ice.
- BRime ice.
- CGlime ice.
154Over inflated tyres may cause damage to the.
- Abrake drum.
- Bwheel hub.
- Cwheel flange.
155 A brake debooster valve is provided for.
- Aapplying brake pressure slowly and releasing the the brakes quickly.
- Bincreasing the pressure and applying the brakes rapidly.
- Cdecreasing the pressure and slowly releasing the brakes.
156Tubeless tyres are stored.
- Aat 15 to 20 P.S.I.
- Bhorizontally maximum of four high with smallest diameter tyre on top.
- Cvertically
157On a wheel bogie unit, positive camber is when the.
- Abottom of the wheels are closer together.
- Btop of the wheels are closer together.
- Cfront of the wheels are closer together
158A badly corroded and pitted brake disk will.
- Awear brake pads too quickly, and should be replaced.
- Bbe serviceable, and provide better grip.
- Cproduce a loss of fluid
159How much oxygen is in a tyre (as a maximum)?.
- A5% by pressure.
- B15% by volume.
- C5% by volume
160A tyre specification 32 x 10.75-14. What does the 10.75 refer to.
- ASection Width.
- BBead diameter.
- COverall diameter.
161When servicing an oleo, fluid comes out of the air valve when the leg is depressurised?.
- AThe leg is serviceable - the separator has bottomed.
- BLeaking air/oil seals.
- CSeparator plate stuck open.
162The type of fluid in an oleo strut will depend upon.
- Atype of fluid most readily available.
- Bthe type of seal material.
- C heat generated in operation of the system.
163A restrictor valve.
- Aspeed up the flow in one direction.
- Bmay be used to slow down undercarriage extension.
- Crestrict the extent of travel of the undercarriage
164The function of the oil in a shock absorber is to.
- Aensure the separator does not bottom.
- Bdamp the rebound.
- C absorb the landing shock
165The purpose of the flutter plate in a shock absorber is to.
- Apermit free flow of oil during compression and restriction of oil during extension.
- Brestrict the compression of the air.
- Cseparate the oil from the air.
166Made up wheels should be stored.
- Avertical at working pressure.
- Bvertical at 20/30 PSI charge.
- Chorizontal no more than 4 high
167After MLG down and securely locked, a red light is illuminated
n the flight deck. The possible causes are."- Ashorted sensor.
- Bout of adjustment sensor.
- Cwiring problem.
168When checking for alignment of a MLG, check.
- Asymmetry, tracking, camber.
- Bsymmetry, splay, tracking.
- Csymmetry, twist, tracking.
169 These markings are found on a tyre32 x 10.45 R 14.What does the number 32 mean?.
- AOuter diameter.
- Bqwidth.
- CInner diameter.
170 A green/grey dot marking on aircraft tyre casing represents.
- Abreather points.
- Bthe light part of the tyre.
- Cmilitary reference.
171In detachable flange type wheels, the flange is secured by.
- Aa retainer plate.
- Ba lock ring.
- Cbolts
172Fuse plugs in aircraft tyres are.
- Afor over temperature protection.
- Bfor overpressure protection.
- Cto deflate the tyre before removal
173 A breaker strip in an aircraft tyre is.
- Ato provide strength.
- Bto provide a wear indication.
- Cto indicate the position for tyre levers.
174If fluid leaks along with air whilst oleo charging, this is.
- Acaused by a leaky seal.
- Bnormal.
- Cdue to excessive charging pressure
175A red dot / triangle mark on aircraft tyres means.
- A military reference.
- Bthe light part of the tyre.
- Cbreather points
176 On selection of MLG down, the gear extends then begins to retract again. The cause is.
- Aa faulty selector valve.
- Ba faulty actuator.
- Cgear lowered at too high an airspeed
177When fitting a tyre, the red dot should be positioned.
- A on the other side of the wheel opposite to the charging valve.
- Bopposite the charging valve.
- Cadjacent to the charging valve.
178Composite brake units.
- Aweigh the same as normal brake units and fade away athigh temperatures.
- Bhave less weight than normal brake units but fade away at high temperatures.
- Chave less weight than normal brake units and have increased efficiency at high temperatures
179A restrictor valve can be used.
- Ato increase the speed of undercarriage retraction.
- Bto increase the speed of the undercarriage extension.
- Cto reduce the speed of the undercarriage extension
180When an undercarriage is lowered, it tends to creep back up. The fault could be.
- Athe emergency system.
- Ba leaky selector valve.
- Ca stuck relief valve.
181Vents holes are found on.
- Atubeless tyres.
- Btubed tyres.
- Ctubed and tubeless tyres.
182At what temperature does a yellow fuse plug melt at?.
- A150°C.
- B250°C.
- C200°C.
183The cam plate in a nose undercarriage is.
- Apart of the shimmy damper.
- Bto align for nose wheel on nose undercarriage retraction.
- Cfor alignment of the nose wheel steering on nose undercarriage extension.
184What is tyre creep related to?.
- AHorizontal movement of the tyre.
- BVertical movement of the tyre.
- CTyre moving around the wheel
185Aquaplaning' can be reduced by.
- Aincreased flaring.
- B lowering slats.
- Can anti-skid device.
186.Why is a hydraulic damper fitted to a nose wheel steering system?.
- ATo reduce vibration and shimmy.
- BTo centralise the nose wheel during an up selection.
- CTo centralise the nose leg assembly during an up selection
187 What decides the type of oil used in an undercarriage leg?.
- AThe material of the leg.
- BThe types of seals the leg uses.
- CNeither, any oil can be used
188In an anti-skid system.
- Abrakes are modulated to give most efficient braking.
- Bbrakes release on rising torque.
- Cbrakes release on falling torque.
189If an undercarriage oleo has insufficient deflection, the likely cause is.
- Aoil level too high.
- Bloss of pressure/leakage.
- Cair pressure too high.
190A Maxaret is used in what system?.
- ATyre inflation.
- BSkid control.
- CSelf centring landing gear.
191The pilot receives an audible warning on the flight deck as the aircraft is descending to land. The most likely reason for this warning is.
- Athe airspeed is too high.
- Bthe landing gear is not locked down.
- Cthe rate of descent is too high.
192A restrictor in the landing gear hydraulic retraction and lowering system is positioned in the.
- Alanding gear up line.
- Blanding gear down line.
- Creturn line from the landing gear selector
193Wheel speed information is used in auto speed brake systems.
- Ato stow the spoilers automatically when the aircraft has nearly stopped.
- Bto ensure the aircraft has touched down and to give a slight time lapse before spoiler deployment.
- Cto ensure the aircraft is still rolling.
194fusible plug fitted to an aircraft wheel prevents.
- Aover inflation of tyres during servicing.
- Bbrakes seizure, if brake stators and rotors weld together under excessive temperatures.
- Ctyre bursts due to high temperatures created by excessive braking.
195If the shuttle valve was stuck in the normal position.
- Aneither system will be available.
- Bemergency braking will not be available.
- Cnormal braking will not be available.
196The breaker strip of a tyre is fitted.
- Abetween the apex strip and the casing piles.
- Bbetween the bead and the casing piles.
- Cbetween the tread rubber and the casing piles
197Nose wheel steering in a modern aircraft is by.
- Arudder pedals.
- Bthe control column.
- Ca separate pilot operated control
198The fusible plugs installed in some aircraft wheel will.
- Afacilitate servicing of the wheel assembly.
- Bmelt at a specified elevated temperature.
- Celiminate the need to check air pressure
199Excessive wear in the shoulder area of an aircraft tyre is an indication of.
- Aunder-inflation.
- Bover-inflation.
- Cexcessive toe-in.
200Ribbed tyres with marker tie bars may be worn to.
- Athe top of the tie bar.
- Bthe base of the tie bar.
- C1 mm from the rib base.
Information
- Description
- Quiz on Sistemas 7, created by oriol arrufat on 29/11/2018.
- Author
- oriol arrufat
- Language
- English
- Views
- 2
- Rating
- No ratings yet Rate this quiz
More on Aircraft Flight Controls