Quiz
Turbina 5
Create a free account to finish this quiz
Save your progress and see your final score.
Already have an account? Sign in
Questions in this quiz (134)
1What are the types of continuous fire detection system?.
- ACapacitance.
- BCapacitance and resistance.
- CInductance and capacitance
2What is the operating principle of the spot detector sensor in a fire detection system?.
- AA conventional thermocouple that produces a current flow.
- BA bimetallic thermoswitch that closes when heatedto a high temperature.
- CResistant core material that prevents current flow at normal temperatures
3In a fixed fire-extinguishing system, there are two small lines running from the system and exiting overboard. These line exit ports are covered with a blowout type indicator disc. Which of the following statements is true?.
- AWhen the red indicator disc is missing, it indicates the fire extinguishing system has been normally discharged.
- BWhen the green indicator disc is missing, it indicates the fire extinguishing system has had a thermal discharge.
- CWhen the yellow indicator disc is missing, it indicates the fire extinguishing system has been normally discharged
4Two continuous-loop fire detection systems that will not test due to a broken detector element are the.
- Athermocouple system and the Lindberg system.
- BKidde system and the Fenwal system.
- CKidde system and the Lindberg system
5Which of the following fire detection systems measures temperature rise compared to a reference temperature?.
- ALindberg continuous element.
- BThermocouple.
- CThermal switch
6A fire involving energized electrical equipment is defined as a.
- Aclass B fire.
- Bclass D fire.
- Cclass C fire
7How are most aircraft turbine engine fire extinguishing systems activated?.
- AManual remote control valve.
- BPushrod assembly.
- CElectrically discharged cartridges
8A fire detection system that operates on the rate of temperature rise is a.
- Athermocouple system.
- Bthermal switch system.
- Ccontinuous loop system
9Why does one type of Fenwal fire detection system use spot detectors wired in parallel between two separate circuits?.
- ASo that a single fault may exist in the system without sounding a false alarm.
- BTo provide an installation that is equal to two separate systems: a primary system and a secondary, or back-up system.
- CSo that a double fault may exist in the system without sounding a false alarm
10How does carbon dioxide (CO2) extinguish an aircraft engine fire?.
- ABy lowering the temperature to a point where combustion will not take place.
- BThe high pressure spray lowers the temperature and blows out the fire.
- C Contact with the air converts the liquid into snow and gas which smothers the flame
11A fuel or oil fire is defined as a.
- Aclass B fire.
- Bclass C fire.
- Cclass A fire
12Which of the following is the safest fire extinguishing agent to use from a standpoint of toxicity and corrosion hazards?
- ABromotrifluoromethane (Halon 1301).
- BBromochlorodifluoromethane (Halon 1211).
- CDibromodifluoromethane (Halon 1202)
13The explosive cartridge in the discharge valve of a fire extinguisher container is.
- Anot a life dated unit.
- Ba life dated unit.
- Cmechanically fired.
14A fire detection system operates on the principle of a buildup of gas pressure within a tube proportional to temperature. Which of the following
systems does this statement define?.- AThermal switch system.
- BLindberg continuous element system.
- CKidde continuous loop system.
15The most satisfactory extinguishing agent for an intake fire is.
- Amethyl bromide.
- Bdry chemical.
- Ccarbon dioxide.
16How is the fire extinguishing agent distributed in the engine section?.
- ASpray nozzles and perforated tubing.
- BSpray nozzles and fluid pumps.
- CNitrogen pressure and slinger rings
17What is the principle of operation of the continuous loop fire
detector system sensor?.- ACore resistance material which prevents current flow at normal temperatures.
- BA bimetallic thermoswitch which closes when heated to a high temperature.
- CFuse material which melts at high temperatures.
18The fire detection system that uses a single wire surrounded by a continuous string of ceramic beads in a tube is the.
- AKidde system.
- Bthermocouple system.
- CFenwal system.
19The fire detection system that uses two wires imbedded in a ceramic core within a tube is the.
- ALindberg system.
- BKidde system.
- CFenwal system.
20A continuous loop fire detector is what type of detector?.
- ARate of temperature rise detector.
- BSpot detector.
- COverheat detector.
21Which of the following fire detection systems will detect a fire when an element is inoperative but will not test when the test circuit is energized?.
- AThe Kidde system and the Fenwal system.
- BThe thermocouple system and the Lindberg system.
- CThe Kidde system and the thermocouple system
22After a fire is extinguished, or overheat condition removed in aircraft equipped with a Systron-Donner fire detector, the detection system.
- Amust be manually reset.
- Bautomatically resets.
- Csensing component must be replaced.
23For fire detection and extinguishing purposes, aircraft powerplant areas are divided into fire zones based on.
- Athe volume and smoothness of the airflow through enginecompartments.
- Bengine type and size.
- Chot and cold sections of the engine
24What is the function of a fire detection system?.
- ATo discharge the powerplant fire extinguishing system at the origin of the fire.
- BTo activate a warning device in the event of a powerplant fire.
- CTo identify the location of a powerplant fire.
25What retains the nitrogen charge and fire extinguishing agent in a high rate of discharge (HRD) container?.
- APressure gauge and cartridge.
- BBreakable disk or fusible disk.
- CPressure switch and check tee valve
26The use of water on class D fires.
- Awill cause the fire to burn more violently and can cause explosions.
- Bhas no effect.
- Cis most effective if sprayed in a fine mist
27The pulling out (or down) of an illuminated fire handle in a typical large jet aircraft fire protection system commonly accomplishes what events?.
- ACloses fuel shutoff, closes hydraulic shutoff, disconnects the generator field, and arms the fire extinguishing system.
- BCloses fuel shutoff, closes hydraulic shutoff, closes the oxygen shutoff, disconnects the generator field, and arms the fire-extinguishing system.
- CCloses all firewall shutoff valves, disconnects the generator, and discharges a fire bottle
28The most satisfactory extinguishing agent for an electrical fire is.
- Acarbon tetrachloride.
- Bmethyl bromide.
- Ccarbon dioxide.
29Which of the following fire detectors are commonly used in the power section of an engine nacelle?.
- ARate of temperature rise detectors.
- BCO detectors.
- CSmoke detectors
30Which of the following fire detection systems uses heat in
the normal testing of the system?.- AThe Kidde system and the Fenwal system.
- BThe thermocouple system and the Lindberg system.
- CThe thermocouple system and the Fenwal system.
31How are extinguisher spray rings checked for freedom from obstruction?.
- AFiring the system.
- BBlowing through with compressed air.
- CPumping water through the system.
32What is used as an extinguishant in fire bottles?.
- AFreon compounds.
- BHalogenated hydrocarbons.
- CWater
33The advantage of the two shot fire bottle system is.
- Aone bottle can be discharged after certain time delay from the other bottle.
- Bboth bottles can be used in either of the engines.
- Cone bottle can be used twice.
34To check a fire bottle in situ is serviceable.
- Aweigh it, check blow out discs, check pressure.
- Bcheck blow out disc only.
- Ccheck blow out disc, pop up indicators, expiry date and pressure
35Resistive type fire-wires are tested using.
- Amegger/ohmmeter.
- Bammeter/ohmmeter.
- Cmegger/voltmeter
36When testing an installed fire bottle.
- Aa multimeter used.
- Ba lamp and 1.5V cell used.
- Ca safety ohmmeter is used.
37On checking a fault free fire detection system.
- Ause megger as per normal.
- Ba megger is never to be used.
- Cuse a megger only for a short while as it can polarise the element.
383 ways to test serviceability of a fixed fire bottle in situ are.
- Aweigh, pressure, blow-out disc.
- Bweigh, pressure, pop up indicator.
- Cpressure, pop up indicator, blow-out disc.
39When installing a flow valve on a 'two shot' fire extinguishing system care must be taken to make sure.
- Aflow arrow should be in a correct direction.
- Bflow valve is pointing towards the respective bottle.
- Cpriority system must have the bigger flow side.
40Omission of crushable washer on engine fire-wire connector will.
- Aallow moisture ingress.
- Baffect fire wire continuity.
- Caffect fire wire capacitance.
41Discharge cartridges of the fire bottle have.
- Alife time in hours/calendar and replace which ever is longer.
- Blife time in hours/or calendar and replace which ever is sooner.
- Cno life time it is only replaced when unserviceable.
42The Kidde Fault Free Fire detection system has how many internal wires in the sensing element?.
- A1.
- B3
- C2
43When testing a two pin fire bottle connector.
- Acontinuity test 1 pin then short two together.
- Bshort two pins together.
- Ccontinuity test 1 pin, then the other, then short two together.
44Gas type fire-wires operate by utilising.
- Athe change in the gas pressure.
- Bthe change in the gas dielectric level.
- Cthe change in the electrical resistance of the gas
45On a fire bottle, if the indicator pin was protruding, this would indicate.
- Athe bottle is under weight.
- Bextinguisher had been fired.
- Can over pressure had occurred in the bottle
46When testing a squib on a fire bottle, you use a.
- Amultimeter (AVO).
- Blow current ohmmeter.
- C lamp and 1.5V cell
47In a two shot fire extinguishing system.
- Aextinguishers distributed once to either engine compartment.
- Bextinguisher distributed twice to each enginecompartment.
- Cone squib can be fired, if that fails then the 2nd squib can be fired
48Methyl Bromide fire extinguisher are installed with neck.
- Ahorizontal.
- Bat the bottom.
- Cat the top
49In a Fenwall fire detection system.
- Athe tube is inconel and wire is nickel.
- Binner electrode is inconel wire.
- Couter electrode is nickel tube.
50When a fire extinguisher is discharged the immediate action is.
- Aoperate engine to idle.
- Bclean with cold water.
- Cclean with hot water.
51Who establishes the recommended operating time between overhauls (T.B.O) of a gas turbine engine.
- AThe engine manufacturer.
- BThe operator (utilizing manufacturer data and trend analysis) working in conjunction with the Airworthiness Authority.
- CThe Airworthiness Authority alone.
52What is the first engine instrument indication of a successful start of a turbine engine?.
- AA rise in oil pressure.
- BA rise in the engine fuel flow.
- CA rise in the exhaust gas temperature.
53A hung start is indicated by the.
- Aexhaust gas temperature exceeds specified limits.
- Bfails to reach idle RPM.
- CRPM exceeds specified operating speed
54During inspection, turbine engine components exposed to high temperatures may only be marked with such materials as allowed by the manufacturer. These materials generally include.
- Alayout dye, commercial felt tip marker, wax or grease pencil.
- Blayout dye, commercial felt tip marker, wax or grease pencil, chalk or graphite lead pencil.
- Clayout dye, commercial felt tip marker or chalk.
55When the leading edge of a first stage turbine blade is found to have stress rupture cracks, which of the following should be suspected?.
- AFaulty cooling shield.
- BOver speed condition.
- COver temperature condition
56A magnetic chip detector inspection should be carried out.
- Awithin a specified time from shut down.
- B with engine cold.
- Cwith engine running.
57What is the proper starting sequence for a turbojet engine?.
- AStarter, ignition, fuel.
- BStarter, fuel, ignition.
- CIgnition, starter, fuel.
58Foreign object damage on a compressor, when boroscoping, is indicated by.
- Atip curl.
- Bnicks and scores.
- Cflats
59Turbine blades are generally more susceptible to operating damage than compressor blades because of.
- Ahigher temperature stresses.
- Bhigher centrifugal loading.
- Chigh pressure and high velocity gas flow.
60A magnetic chip detector detects.
- Aparticles held in suspension.
- Bparticles which are too small for the naked eye.
- Cferrous particles only.
61A cool-off period prior to shutdown of a turbine engine is done to.
- Aprevent vapor lock in the fuel control and/or fuel lines.
- Bprevent seizure of the engine bearings.
- Callow the turbine wheel to cool before the case contracts around it.
62When starting a turbine engine, the starter should be disengaged.
- Aonly after the engine has reached full idle RPM.
- Bwhen the ignition and fuel system are activated.
- Cafter the engine has reached self-sustaining speed.
63What should be done initially if a turbine engine catches fire when starting?.
- AContinue starting attempt in order to blow out the fire.
- BContinue engine start rotation and discharge a fire extinguisher into the intake.
- CTurn off the fuel and continue engine rotation with the starter
64A turbine engine hot section is particularly susceptible to which kind of damage?.
- AScoring.
- BGalling.
- CCracking.
65If a turbine engine is unable to reach takeoff E.P.R before its E.G.T limit is reached, this is an indication that the.
- Afuel control must be replaced.
- BE.G.T controller is out of adjustment.
- Ccompressor may be contaminated or damaged
66Which of the following engine variables is the most critical during turbine engine operation?.
- ACompressor RPM.
- BTurbine inlet temperature.
- CCompressor inlet air temperature.
67With the engine running at idle, the E.P.R system reads just over 1.
- AThe system has failed and needs attention.
- BThe system needs re-calibration back to '1'.
- CThis is a normal condition and does not need attention
68The recurrent ingestion of dust or other fine airborne particulates into an engine can result in.
- Athe need for less frequent abrasive grit cleaning of the engine.
- B foreign object damage to the compressor section.
- Cerosion damage to the compressor and turbine sections.
69When the engine is not running, and engine blanks are installed. The E.P.R gauge shows 1.0, then.
- Athe transmitter is faulty.
- Bthe receiver is faulty.
- Cit is normal
70Which of the following may be used to accomplish internal inspection of an assembled gas turbine engine?.
- AUltrasound, and fluorescent penetrant and ultraviolet light.
- BX-ray and a borescope.
- CInfrared photography and fluorescent penetrant and ultraviolet light.
71Run down time is indicative of.
- Aan F.C.U malfunction.
- Bcompressor malfunction.
- Cthe freedom of rotation of the compressor
72A hung start or false start is one in which.
- Alight up' occurs, but the RPM does not increase.
- Bthere is no 'light up'.
- Cthe engine does not rotate
73What would be the possible cause if a gas turbine engine has high exhaust gas temperature, high fuel flow, and low RPM at all engine power settings?.
- AFuel control out of adjustment.
- BLoose or corroded thermocouple probes for the E.G.T indicator.
- CTurbine damage or loss of turbine efficiency
74In regard to using a turbine engine oil analysis program, which of the following is NOT true?.
- AIt is best to start an oil analysis program on an engine when it is new.
- BA successful oil analysis program should be run over an engine's total operating life so that normal trends can be established.
- CGenerally, an accurate trend forecast may be made after an engine's first oil sample analysis
75Which of the following is the least likely indication of a main bearing failure?.
- AHigh oil consumption.
- BHigh oil temperature.
- CHigh oil pressure.
76After shutdown, flames are present in the exhaust pipe. The probable cause is.
- Aa defective fuel control unit (F.C.U).
- Ba defective pressurizing and dump valve.
- Ca defective H.P cock
77If the L.P cock is used to shutdown an engine.
- Athe F.C.U will continue to function.
- Bflames will appear in the exhaust.
- Cthe H.P fuel pump will run dry
78When accelerating from 'light-up' to ground idling speed, the E.G.T will.
- Aremain constant.
- Bincrease above idle value then decrease to normal.
- Cdecrease below idle value then increase to normal.
79A gas turbine engine is stopped by closing.
- AL.P cock.
- BH.P cock.
- Cthrottle valve
80A 'wet start' is indicated by.
- Ano temperature indication.
- Blow RPM.
- Ca prolonged cranking period.
81The engine accelerates to idling by.
- Agas flow.
- Bcombined efforts of starter motor and gas flow.
- Cstarter motor.
82An oil emission spectrometer measures.
- Aparticles in suspension.
- Bparticles on the surface.
- Cspecific gravity of the oil.
83A broadband vibration reading indicates.
- Athe total vibration sensed by the transducer.
- Bthe peak allowable vibration.
- Cthe N1 vibration.
84Vibration analysers determine which component is vibrating by analysing.
- Avoltage.
- Bamplitude.
- Cfrequency.
85High frequency vibration.
- Acauses engine components to crack.
- Benergises air particles prior to compression.
- Ccan give an indication of a fluctuating (E.P.R)
86Engine oil sampling analysis is taken.
- Aafter engine shut down.
- Bat specific time after engine shut down.
- Cwhen oil level is high.
87With external power applied, the engine will not run up to idle after reaching starting speed. The likely fault would be with the.
- AFuel Control Unit.
- Bclutch.
- Cbattery
88When running down an engine.
- Ait should be done as slowly as possible to assist thermal stress.
- Bit should be done as quickly as possible to stop excess of fuel gathering.
- Cit should be done as slowly as possible to reduce thermal stres.
89What may be an indication of a bleed valve stuck in the closed position?.
- AOver speed.
- BLow E.G.T reading.
- CCompressor stalling at low RPM.
90Excessive E.G.T can.
- Acause N.G.V to creep.
- Bcause damage to turbine.
- Ccause damage to jet pipe
91 A jet engine has a high oil temperature but all other power parameters are normal. The probable cause is.
- Aa large quantity of oil being returned to tank.
- Bgear box leakage.
- Ca main bearing in distress.
92When cleaning salt from a compressor.
- Ause water then manufacturer's cleaning solution.
- Buse water at low power then water at high power.
- Cnever use water, use only the recommended solution
93A hot start refers to.
- Aearly ignition.
- Bhigh E.G.T before idle RPM is achieved.
- Ctoo much fuel being supplied
94If a compressor surge occurs, it is recognized by.
- Acoughing in the compressor and vibration.
- Bfluctuating RPM and fuel flow.
- Cfluctuating E.G.T and thrust
95Cracks may occur in hot section components of a turbine engine if they are marked during inspection with.
- Aa lead pencil.
- Bchalk.
- Clayout dye
96What must not be used during an engine compressor wash?.
- AChlorine.
- BDesalinization solution.
- CCrushed almond.
97Trend monitoring of spectrometric oil analysis is carried out how often?.
- ADuring each scheduled maintenance period.
- BAt set periods once the rate of wear has been established.
- CAfter every repair or modification
98Starting an engine with a bleed valve stuck closed would cause:.
- Alow E.G.T.
- Bpossible stalling of the engine.
- Chigh E.G.T.
99Galling is a condition caused by excessive.
- Achafing.
- Bscoring.
- Ctemperatures.
100If a burner was down, in a multi-can system, the engine would tend to.
- Ahang up.
- Brun up.
- Csurge.
101If the rundown time is less than the minimum stated for a given engine.
- Aunacceptable wear is occurring at the main bearings.
- Bthe rotating assembly is free.
- Cthe rotating assembly is being restricted.
102When running an engine the following lights should be on:.
- Aanti-collision and nav-lights (if fitted).
- Bnav-lights (if fitted).
- Canti-collision (if fitted).
103With spectral oil analysis program (S.O.A.P), samples are taken.
- Awhen the oil tank is full.
- Bat a specified interval.
- Cwhen the oil is warm
104During start, if a bleed valve is stuck closed.
- AE.G.T is unaffected.
- BE.G.T will be higher than normal.
- CE.G.T will be lower than normal
105Dynamic balance testing locates unbalance in.
- Aall planes.
- Btwo planes.
- Cone plane.
106On a gas turbine engine with baked oil deposits, how would you carry out grit blast cleaning With the engine at?.
- Astationary.
- Bidle speed (low).
- Chigh speed
107A rotation pad on an accessory drive gear box is provided for.
- AN2 rotation.
- Bboth are correct.
- Calternate tachogenerator fitment
108What would be indicative of a hung start?.
- AStarter would fail to disengage.
- BHigh E.G.T.
- CEngine would fail to reach self sustaining speed
109Fuel system inhibiting oil is.
- Amineral oil.
- Blight anti-freeze oil.
- Ckerosene
110After placing an engine in an M.V.P envelope.
- Acheck humidity indicator after 12 hours.
- Bcheck humidity indicator after 24 hours.
- Ccheck humidity indicator after 48 hours.
111On a vapour proof cocoon, there is a.
- Atemperature indicator.
- Bmoisture indicator.
- Chumidifier
112When an installed engine is not to be used for a period of up to 7 days.
- Ait is necessary to inhibit the engine.
- Bit is only necessary to blank off all apertures.
- Crun the engine as prescribed in the Flight Manual.
113Installed engines must be re-preserved after preservation at least every.
- Asix weeks.
- Bsix days.
- Csix months.
114On storage of an engine, the desiccant is.
- Alooked at within 24 hrs if its blue its OK.
- Blooked at 24 hrs later if its blue its OK.
- Clooked at 24 hrs later if blue it should be replaced
115After placing an engine into storage, details would be recorded in.
- ATechnical Log.
- BEngine log book.
- CAircraft log book
116When storing an engine the fuel system is to be inhibited. How is this done?.
- ARemove plugs rotate engine then add oil.
- BRotate engine whilst adding oil then remove plugs.
- CAdd oil leaving plugs in.
117An engine in storage for 7 days should.
- Ahave storage oil placed in engine.
- Bbe run twice in that week.
- Cbe fitted with covers and blanks and apertures covered.
118On a (VP) cocoon bag, if the humidity indicator turns pink/lilac.
- Adesiccant is effective and does not need changing.
- Bdesiccant is ineffective and needs changing.
- Cdesiccant is changed weekly
119To inhibit the fuel system of an installed engine.
- Apump oil into the engine when stationary.
- Bdry motor the engine.
- Cremove the ignitor plugs
120When is the humidity indicator checked on a preserved engine?.
- A1 Month.
- B1 Year.
- C6 Months.
121With an engine in storage, desiccant is used.
- Aas an insecticide.
- Bas a corrosion inhibitor.
- Cto remove moisture from the air.
122Small cuts in a M.V.P. engine storage bag can be repaired.
- Awith adhesive PVC tape.
- Bby vulcanising.
- Cby replacing M.V.P.
123When removing an engine for long-term storage, bleed valves should be.
- Aremoved.
- Blocked closed.
- Copen but blanked.
124The types of water present in aviation fuel are.
- Afree and entrained both harmful.
- Bfree that is harmful and entrained that is harmless.
- Cfree that is harmless and entrained that is harmful
125Oil pressure and scavenge pumps are usually.
- Aspur gear pumps.
- Bmulti-plunger pumps.
- Cdiaphragm pumps.
126The purpose of a pressure filter in a lubrication system is to.
- Aprotect the pressure pump.
- Bprotect the oil jets.
- Cprotect the scavenge pumps
127a curvic coupling.
- Aconverts rotary motion to reciprocating motion.
- Babsorbs misalignment between the driving and driven shafts.
- Caccurately aligns the driving and the driven shafts
128Feeders are.
- Aconduits used to carry electrical cable.
- Bfluid supply hoses.
- Cheavy duty electrical generator cables.
129High air humidity will.
- Ahave no affect on thrust.
- Breduce the thrust output.
- Cincrease the thrust output
130C.I.T sensor is made up of.
- AIron-constantan.
- BChromel-alumel.
- CPlatinum-rhodium
131What is the maximum value of pressure with reference to a jet engine?.
- A1 Bar.
- B1 Kg/cm.
- C1 Atmospheric Pressure.
132The hottest casing is the.
- AH.PT.
- Bcombustion chamber.
- CL.PT
133Centrifugal compressor maximum tip speed is.
- A0.8 Mach.
- B1.2 Mach.
- C0.5 Mach.
134What type of oil is used in a gas turbine engine?.
- A Phosphate Ester.
- BSynthetic.
- CMineral
Information
- Description
- Quiz on Turbina 5, created by oriol arrufat on 17/07/2019.
- Author
- oriol arrufat
- Language
- English
- Views
- 1
- Rating
- No ratings yet Rate this quiz