Quiz
sistemas 10
Create a free account to finish this quiz
Save your progress and see your final score.
Already have an account? Sign in
Questions in this quiz (200)
1a loss of streght resulting from cyclic loading is know
- Ametal fatigue
- Bage hardening
- Cfail safe
2zone 320 under ATA system is
- Avertical stabiliser
- Bcentral stabiliser
- Chorizontal stabiliser
3the fuel drain of a combustion heater must be protected from
- Aice build-up
- Blightning strike
- Caccidental damage
4engine mounts provide for
- Alogitudinal movement
- Btorsional movement
- Clateral movement
5dyna engine mounts
- Areduce vibration from engine to airframe
- Bprevent all vibration from engine to airframe
- Care constructed from plastic
6how is damadge to the nose cone of an aircraft prevented during a lighting strike
- Aearthing strap
- Bbonding strip
- Cspecial paint
7tension is the stress of
- Aeloganting or strench
- Bcrush or comprension
- Ctwisting
8a fuselage station
- Alateral point on aircarft fuse
- Blogitudinal point on the aircraft fuselage
- Clateral point on aircarft wing
9composite materials are bonded by
- Aspecial paint
- Bcopper wire
- Caluminium wire
10ata zone 100 is
- Aupper fuselage
- Blower fuselage
- Cleft-hand wing
11what forceis an I-Beam subjected to
- Atension
- Bbending
- Cshear
12in ATA 100 zonal system the passenger entry door will have a designation of
- A400
- B800
- C600
13wings stations are measured
- Aoutboard from the wing root
- Binboard from the wing upper surface
- Coutboard from the fuselage centreliine
14wich of following is primary structure?
- Astringer
- Bframe
- Cskin
15bending stresses are combination of
- Atension and compresion stress
- Btorsional and compression streses
- Ctension and shear stresses
16to prevent a system being affected by high current flows after lighting strike a composite aircraft electricity is discharged throught
- Aelectrically conected primary conductors
- Bsprayed coat of non-conductive paint
- Ca sparayed coat of conductive paint
17wrinkling of the skin on the upper surface of fuselage indicates
- Asagging
- Bsheding
- Chogging
18when applying a doubler plate,what els could you use for estra strength
- Athicker material
- Ba waffle plate
- Ca tripler plate
19Hi-lock fastener installation requieres that
- Aan interference fit hole is drilled
- Bthe shank is lubricated
- Cthe fastener is accurately torqued
20contact betwen titanium and phosphate ester fluid should be avoided beacuse
- Athere is no effect
- Bit makes the titanium soft
- Cit makes the titanium brittle
21the optimum atmospheric conditions for painting aircraft is
- Abetwen 65º F and 75ºF with less than 75% relative humidity
- Bbetwen 65º F and 75ºF with more than 75% relative humidity
- Cbetwen 60º F and 77ºF with less than 75% relative humidity
22to remove a rivet you should
- Adrill it all way throught
- Bdrill to the depth of the head
- Cdrill half way trough
23kevlar should be stored
- Ahorizontally
- Bin moisiture prof bags
- Cvertically
24blowout panels fitted to floors of pressurised aircraft to
- Aprovide acces for pressurising cargo bays
- Bprovide acces for pressurising the cabin
- Cprovide venting should a differential pressure build up across the floor
25what are passanger windows normally made from
- Aglass
- Bacrylic
- Cacrylic/gass laminate
26a firewall bulkhead is usually made from
- Atungsten
- Btitanium
- Csteel
27acrylic windows must be able to flex in-situ because they have
- Aslight shrinkage due to age
- Bsmaller coefficient of expansion than souronding structure
- Clarger coefficient of expansion than souronding structure
28a cargo bay must have sings stating
- Amaximum loading
- Bmaximum dimensions
- Cno harzardous cargo
29zone d cargo compartment windows
- Aare made from fire retardan Perpex
- Bmust be blanked off
- Cmust have blinds pulled down
30windscreen delamination is
- Aseparation of the glass from the vinyl interlayer
- Bbubbling of the glass due to overheat
- Cwindscreen peeling away from the airframe
31what is the ideal storatge temperature for windscreen panels
- A50ºC to 70ºC
- B30ºC to 50ºC
- C50ºF to 70ºF
32what is the maximum temperature of warm water which is used to clean dirty aircraft acrylic panels?
- A125ºF
- B104ºF
- C40ºF
33how are passenger doors pressure load transmitted to the fuselage structure?
- Aby door stops
- Bby pressure seals
- Cthrought the latching mechanism
34passenger cabin windows are constructed with two panes and seal betwen them . Under normal flight conditions wich panels take the differential pressure loads
- Ainner
- Bboth
- Couter
35how are passenger seats secured to the flor
- Aby the front legs while the back attachmends provide anti rattle
- Bby both front and back legs
- Cby the back legs while front attachment provides anti rattle
36a material commonly used for pressure bulkhead sealing is
- Asoft rubber
- Baluminium
- CPTFE
37when acrylic and sheet metal is joined toghether , allowance should be made for
- Agalvanic corrosion of the metal
- Bexpansion of the acrylic due to heat
- Cexpansion of the metal due to heat
38which of following is perspex resistant to
- Aacetone
- Bmek
- Ckerosene
39in a pressurised aircraft cabin window , the differential pressure can be taken by
- Athe sracth panel
- Bthe inner pane only
- Cboth main panes
40the purpose of the vinyl interlayer in window construction is
- Ato increase static strenght
- Bto improve on brittle behaviour
- Cto enable inclusion of heater film
41on passanger waircraft of two or more zones
- Athere should be at least one exit per zone
- Bthe seat back fold forward at over wing emergency exits
- Cthe emergency exits are to be clearly signed
42class d cargo bay windows require
- Adouble acrylic panels
- Bthe blind down for flight
- Cfire proof coatings
43cargo bay panels are normally constructed from
- Amonolithic Nomex
- Bfibreglass and resin
- Ckevlar
44the aftigue life of a pressure hull is based on
- Athe number of negative differential pressure aplications
- Bthe number of explosive decompressions
- Cthe total number of pressurizations
45in pressurized aircraft , undercarrige bays
- Aare unpressurised
- Bmaybe presurized or unpressurized
- Care pressurized
46the main logitudinal membres in fuselage are called
- Aspars
- Bframes
- Clongerons
47a partition within the aircraft structure is called a
- Abulkheads
- Bcleats
- Cframe
48when inspecting a stowage doors , special attention should be given to the
- Acatches
- Blight microsiwthes
- Ctrim
49seat track cutouts provide for various seat spacings , usually in
- Ahalf inch increments
- Bone foot increments
- Cone inch increments
50wall mounted flight attendant seats are fixed to
- Atracks
- Bstanchions
- Crails
51windshields are heated to
- Amaintain stregth and toughness only
- Bdemist , anti-ice and maintaint strenght and toughness
- Cprevent misting and icing only
52the internal doors of an aircraft
- Aonly carry pressure load ehrn the aircraft is at cruise altitude
- Bcarry pressure loads
- Cnever carry pressure loads
53a pressure door warning light illuminates only when the door is
- Anot locked
- Blocked
- Cnot fully opened
54if an electrally operated cargo door lifting actuator fails , it may be operated
- Aby electrical ground power
- Bby alternate actuators
- Cmanually by winding
55after installation of an acrylic window panel , protective paper and adhesive remaining on the panel may be removed by use of soap and water and
- Acellulose thinners
- Bmethylated spirits
- Cmek
56if heat is applied to the vinyl interlayer of an aircraft windscreen , its ability to withstand impact will
- Aincrease
- Bdecrease
- Cnot change
57when fitting a transparent plastic panel (acrylic)to metal frame , provision must be made for the realtive movement of the panek and the frame for the reason of
- Athe know slight shrinkage of the panel due to ageing
- Bthe lower coefficient of expansion of the transparent panel when compared with the frame
- Cthe higher coefficient of expansion of the transparent panel when compared with the frame
58perpex is resistant to
- Aparaffin
- BC.T.C
- Cacetone
59moisiture drain valves in a pressurised fuselage
- Aare open all the time to ensure the bilge are well drained
- Bare open when the cabin is depressurised
- Cre open whrn the cabin is pressurised
60wide body transport aircraft have cabin floor vents
- Ato equalise pressures above and below the floor after the loss of a cargo compartment door
- Bto enure adequate ventilation of the underfloor areas
- Cto provide acces to class A cargo compartments in the event of fire
61on an inspection , you are aware of vinyl bubbling . What accion is requeired
- Areplace the defective windows
- Bonly replace the window if the bubblig affects vision
- Cno accions is requiered with this defect
62passanger windows in a jet transport aircraft normally have
- Atwo structural panes
- Bone structural pane
- Cthree structural panes
63a plug type window is fitted
- Afrom the outside
- Bfrom the inside
- Cfrom ethier side
64air is used to seal the cabin door in pressure cabins . The source of this air is usually
- Acabin pressurised air
- Bfrom storatge bottles
- Cambient pressurised air
65drain valves are normally closed by
- Arubber strips
- Bcabin air pressure
- Cspring pressure
66drain holesin unpressurised areas are
- Aalways closed
- Balways open
- Cethier open or closed
67a cargo compartment in which there is a separated approved smoke fire detector system to give warning and means to shut off the warning airflow to the compartment
- AClasse E compartment
- BClasse B compartment
- CClasse C compartment
68aircraft frames are constructed of
- AU section
- BI section
- CZ sections
69the life of a fuselge depends on
- Athe pressurisation cycles excluding maximum differential
- Bthe pressurisation cycles not including ground cycles
- Call pressurisation cycles
70passenger cabin seat rails form part of the
- Alongerons
- Bstringers
- Cframes
71a false rib is usually used to
- Asupport and give aerodynamic shape to the wing leading edge
- Blose a torsion box structure
- Callow the fitment of aileron control tubes through a wing
72one purpose of a rib is to
- Amantain the correct countour of an aerofoils covering
- Bsupport the bending loads on a fuselage
- Cfrom the main lateral member in an aerofoil
73what is canteliver wing
- Aone that has external supporting struts
- Bone that has no external supporting struts
- Cone that folds for acces to limited space
74a wing leading edge would have provisions and linkages for slats and
- Aleading edge flaps
- Bslots
- Ctrailing edge flaps
75Aileron reversal is caused by a structure that has a low stiffness in
- Atorsion
- Bbending
- Cshear
76the principle load bearing members of the wing are
- Astruts
- Brib
- Cspars
77upper wing skin on a large transport aircraft is made from
- A7075
- B2024
- C7118
78variable incidence tailplane
- Amove rapidly when trimming the aircaraft during the leading approach and slowly at all other times
- Bmove rapidly when trimming the aircaraft during climb out and landing approach and slowly during cruise
- Calways move slowly
79to correct for nose haviness on an aircraft fitted with a variable incidence tailplane , the incidence of tailplane would be
- Aincreased , wich is done by loweing the leading edge
- Bdecreased , wich is done by loweing the treailing edge
- Cdecreased , wich is done by loweing the leading edge
80costrucction such as horn balance and inset hinge balance installed on control surface assembly
- Ais meant to trim CG of control surfaces
- Bserves as a "servo"system of balance
- Chas same effect of balance tab
81ATA chapter for nacelles / Pylons is
- A54
- B55
- C53
82wing mounted podded engines and integral fuel tanks
- Areduce tailplane download
- Bprovide increased safety if undercarriage collapses on landing
- Cprivide wing bending relif
83the mounting bolts are tightened so the engine can move
- Afore and aft
- Blaterally , longitudinally , vertically
- Ctorsionally
84a pack valve controls
- Aair flow
- Bair temperature
- Ctrim air
85in a large air conditioning systems , the main fan is activated to
- Aensure conditioner air is distuied
- Bensure conditioned air is distribuied and mantain positive duct pressure
- Censure positive duct pressure is maintained
86acm compressor will
- Arise
- Bfall
- Cremain the same
87cockpit ventilation is requiered to be
- A10 litres per crew member per minute
- B10 cu/ft per crew member per minute
- Cselected by the crew
88a large aircraft air cnditioning system`s cabin temperature control
- Ais selectable for each zone individually from the flight station
- Binvolves modulating the pack valve
- Call zone temperatures are controlled from one master switch
89an adventatge of using air cycle system over the vapour cycle system in aircraft is
- Aboth air conditioning and pressuritzation are obtined
- Bwheight reduction by avoiding big tanks carrying freon gas
- Cless hazardous than vapour cycle system
90what is the maximum allowable concentration (by volume)of carbon monoxide in occupied aircraft compartment?
- A0.005%(50 p.p.m)
- B0.02% ( 200 p.p.m)
- C0.01% (100 p.p.m )
91the first component that the charged air enters from the IP compressor is
- Athe bleed valve
- Bthe check valve
- Cthe pre-cooler
92the termostatic valve sensing bulb is located just before
- Athe evaporator
- Bthe compressor
- Cthe condenser
93in typical vapour cycle system , the sub-cooler
- Ais heat exchanger to superheat the vapour
- Bcools the vapour further to prevent slugging
- Cdelivers extra cooling effect when the aircraft is on ground
94in air conditioning system , heat is added to air by
- Aresticting compressor inlet
- Bresticting the compressor outlet
- Crestricting duct outlets
95before filling a vapour cycle cooling system
- Apre-heat the system to 100 ºF
- Bflush the system with a solvent
- Capply suction to remove air and moisture
96subsequent to passing throught the primary heat exchanger , the supply air in a turbo-fan cold air systems flows to the
- Aintercooler or secondary heat exhanger
- Bturbine
- Cfan
97pressurisation system may be inhibited by
- Aair/ground microswitches
- Bflap microswitches
- Cthrottle microswitches
98cabin outflow valve provide
- Aoutflow of cabin pressure and pressure warning
- Boutflow of cabin pressure and ventilation
- Ccabin positive pressure and negative (suction) pressure
99on the ramp , the pre-cooler obtains its cooling by
- Afan inducement
- Bgas expansion
- Cram air
100the electricall spill-valve operates on signals from
- Athe venturi metering duct
- Bthe latching solenoid
- Cthe pressure controller
101during taxiing , the cabin pressure in a large aircraft is
- Abelow atmospheric pressure
- Babove atmospheric pressure
- Cat atmospheric pressure
102cabin pressure is normally controlled by the rate of
- Aair discharge
- Bclimb or descent
- Cair supply
103a standby ADI uses
- Avertical gyro
- Ba space gyro
- Can erth gyro
104indicator glasses are bloomed to
- Areduce reflection
- Bminimise parallex error
- Crender dust unable to settle
105slat asymetri may be monitored by using
- Aposition pick-off
- Bspring actuators
- Ctorque sensors
106A standby compass has a pair of magnets for adjustment . They are initially placed
- Aparallel with each other
- B90 degrees to each other
- C45 degrees to each other
107component P affects
- Acoefficient B
- Bcoefficient A
- Ccoefficient C
108a vacuum mercury gauge reads 5 in. This pressure is
- Aabove zero pressure
- Bbelow ambient pressure
- Cabove ambient pressure
109a gyro spinning on a vertical axis will detect the aircraft's
- Ayaw and pitch
- Byaw only
- Croll and pitch
110an artificial horizon uses
- Aa directional gyro
- Ba vertical gyro
- Ca rate gyro
111vibration levels are indicated to the flight crew in
- Arelative amplitude
- Bphons
- Cdb
112th rigging of a non magnetic proximity sensor requieres
- Acheking the target clearance in the FAR position againts reference figures
- Bcheking the target clearance in the NEAR position againts reference figures
- Censuring the target contacts the sensor
113how you detect and locate the leak in a pitot-static system ?
- Aisolate the component and perform a system check , starting from the instrument
- Bpressurize the system and use the soap buble detection method
- Cdisconect each line in a turn and pressure leak test
114following reaplacment of a separately mounted compass corrector box , a compass calibration swing will be requiered
- Awithout exception
- Bonly if initial variation is grater than 5 degrees
- Conly if correctors are not mached to the ones being removed
115A +/. symbol on a compass system indicates
- Amagnetic deviation and compass card are alignment and direcctional gyro are being synchronised
- Bcompass card and direcctional gyro are being synchronised
- Cfailure of the compass systemik
116during a climb the pressure in the VSI capsule will be
- Aequal to the pressure in the case
- Bgrater than the pressure in the case
- Clower than the pressure in the case
117corrections to a mechanical ASI are for
- Asquare law and temperature
- Bsquare law
- Csquare law error and temperature
118two fundemental properties of a gyro are
- Awander and rigidity
- Brigidity and precession
- Cprecession and wander
119vertical gyros are limited to 85 º degrees movement in pitch to prevent
- Agyro topple
- Bgimbal lock
- Cpitch overshoot
120a tacho generator pointer is moved by a
- Adrag cup coupling
- Ban AC servo motor
- Ca torque synchro reciver
121an altimeter in a pressurised aircraft at altitude has a case leak . The altimeter will
- Aover read
- Bnot be affected
- Cunder read
122under what condition is indicated altitude the same as true altitude ?
- Anever
- Bat sea level in standard conditions (ISA)
- Cwhen at 18.000 feet MSL with altimeter set at 29.92
123the earth's magnetin dip affects standby compass
- Aabove its pivot only
- Bequally above and below its pivot
- Cbelow its pivot only
124an electrical gyro has usually speed of
- A10.000 RPM
- B5.000 RPM
- C20.000 RPM
125A flux valve is used to
- Aaling the directional gyro with the earth's magnetic field
- Baling the standby compass with the earth's magentic field
- Cdrive HSI
126what instrument connects to pitot pressure?
- Aboth the airspeed indicator and
- Bthe vertical speed indicator
- Cthe airspeed indicator
127The TX and RX rotors of a control synchro are 90º degrees shifted . The output is
- Azero
- Bhigh
- Clow
128when testing using a thermocouple test set
- Ano power is requeired
- Ba serviciable bttery is requiered
- Ca 28 VDC supply is requiered
129a positive coefficient A adjustments of a compass will give heading
- Aincrease on East/West heading
- Bincrease in all headings
- Cdecrease in all heading
130A tacho generator has
- Aits own independent electric system
- B28 V applied
- C115 V apllied
131what could cause fluctuations in instruments
- Awater in static line
- Bstatic blocked
- Cpitot blocked
132a compass swing would be requiered after replacing a
- Acompass amplifier
- BH.S.I
- Ccompass sensing unit
133on a turn and slip indicator , the needle points to the right , and the ball is to the left . The aircarft is
- Aover-banked , slipping into the turn
- Bover-banked , slipping out the turn
- Cunder-banked ,skidding out of the turn
134the true airspeed computed from IAS takes into account
- Aradar altitude
- Btemperature only
- Ctemperature and altitude
135where is the altitude director gyro stator situated
- Ainside the rotor
- Bunderneath the rotor
- Caround the rotor
136what is the error in the lubber line called?
- Acoefficiant B
- Bcoefficiant P
- CIndex eror
137the maximum deviation an a standby magnetic compass must not be more than
- A5º
- B3º
- C1º
138compass base classification Class 2 is periodically re-surveyed every
- A1 year
- B5 years
- C2 years
139the aircraft heading is 270º . The magnetic deviation is -1º . The pilot should fly
- A271º
- B270º
- C269º
140true rundway heading is
- AQFU
- BQDM
- CQDR
141Apparent drift of a vertical gyro is a function of
- Asin of latitude
- Bcos of latitude
- Ctan of latitude
142a machmeter works
- Aalways escept on the ground
- Babove 10.000 ft
- Calways
143radio marker information is displayed on
- AADI
- BEICAS
- CHSI
144angle of attack alarm is souronding too close stall . Rectification is to
- Amove probe down
- Bmove probe laterally
- Cmove probe up
145where is alpha angle used
- Aaccelerometer
- BIRS
- CAngle of attack
146where is the spinup/rundown brake on a gyro instrument
- Ainner gimbal
- Broatating vane
- Couter gimbal
147on repleacing a pre-indexed flux valve you would
- Afit serviciable pre indexed flux valve into the same position as the unserviciable pre indexed flux valve was removed from
- Bcarry out a check swing afet fitment
- Caling the aircraft onto its "A" coefficient so that error is induced
148IN airways flying , what is the barometic scale of the altimeter set to ?
- A1013.25
- BQFE
- CQNH
149vivbration monitoring signals are sent
- Avia signal conditioner to the gauge
- Bvia half-wave rectifier to the gauge
- Cdirect to the gauge
150the vacuum system gauge reads 5 inches of mercury . This is from
- Aambient and minus
- Bzero and positive
- Czero and minu
151the boundary layer of a body in a moving airstream is
- Aa layer of air over the surface where the airspeed is changing from free stream velocity to zero velocity
- Ba layer of air which is moving at free stream speed
- Ca thin airflow changes from subsonic to supersonic flow
152the transition point located on the wing is the point where
- Athe boundary layer change from laminar to turbulent flow
- Bsirflows starts separating from the wing
- Cthe airflow changes from subsonic to supersonic flow
153the aeroplane fin is of symmetrical aerofoil section and will therefore provide a side-load
- Aonly if situable angle of attack develops due to yaw
- Bonly when rudder is moved
- Cif a situable angle of attack develops due ethier yaw or rudder movement
154the direcctional Gyro is cheked every 15 minuts
- Adrift
- Btoppling
- Cerection
155in a directional gyro , the inner/outer gimbal is corrected to
- A15 sine longitude
- B15 cosine latitude
- C15 sine latitude
156A desicant used in the storatge of instruments
- Ais sodium-bicarbonate
- Bis silical-gel
- Cis anti-freeze oil
157an aircraft with Mach warning will warn
- Awhen M (base=crit) is reached
- Bwhen Mach 1 is exceeded
- Cwhen envelope limit is reached
158SELCAL is used to
- Aalert ground stations
- Balert other aircraft
- Cmonitor ground signals
159HF comunication frequency is in the range
- A23-30 khz
- B3-30 Mhz
- C108-118 Mhz
160the polythene sleeving over a HF antenna is to stop
- Alghtning strike
- Bprecipitation static
- Cmositure ingres and corrosion
161the term HIRF means
- Ahigh interference radiated fields
- Bhigh intensity radiated fields
- Chigh intensity radio fields
162the fundamental theory of operation of a ranging radar is
- Afrequency of returns
- Bpercentatge of emitted signal returned
- Ctime to taken to receive returns
163on aircraft cummunication system , HIRF interference is most prominent
- Aduring transmissions only
- Bat specific frequencies
- Cacross the whole frequency spectrum
164what clock is used in a GPS satellite?
- Aclock with baterry
- Batomic
- Cquartz
165with control wheel stering (cws) , if the flight path is disturbed by the pilot , the course will be corrected by the
- Aautopilot panel
- Bflight director input
- Cnormal flight control
166an HF coupling is used to match the
- Areciver
- Bboom-set (headphones and mic)
- Caerial
167On an aircarft's navigation display , distance mesuring equipment gives
- Aslant range to beacon
- Bhigh and range to beacon
- Cground range to beacon
168IN GPS system what type of clock is in the receiver?
- AAtomic
- BQuartz
- CBattery
169what is the purpose of the autopilot?
- Ato relive the flight crew of their duties during long haul flights
- Bto reduce the flight crew's workload
- Cto enable the aircarft to land in bad weather
170On ATC radio readability scale , what is satisfactory reception
- A1
- B3
- C5
171An ADF system includes
- Aa sense antenna
- Bboth a sense and loop antenna
- Ca loop antenna
172a category 2 landing rvr is
- A400 m
- B200 m
- C800 m
173frequencies used for a microwave Landing System are
- A5-5.1 khz
- B5-5.1 ghz
- C5-5.1 mhz
174where is the anntena located for waching the tv
- Aon the fuselage roof
- Bin stabiliser tip
- Cnear the wingtips , away from the cabin
175in a servo loop , an LVDT provides
- Arate feedback
- Bethier rate or position feedback
- Cposition fedback
176transmitter aerials radiate
- Aelectromagnetic enregy only
- Belectrostatic and electromagnetic energy
- Celectrostatic energy only
177when a turbulence mode is selected , wich other mode will not be available?
- Aheading hold
- BALT hold
- CVOR
178priority messages in aircraft centralised warning system , go in order of (lowest to highest
- ATCAS , GPWS , windshear
- BGPWS ,windshear, TCAS
- CTCAS , windshear , GPWS
179full scale defelction of the glideslope pointer from yhe centerline is
- A0.5º
- B2.5º
- C3º
180IRS obtains basic position information by
- Aintegrating tha ccelerometer output
- Bintegrating twice the acceleramoter output
- Cdiferentiating tha ccelerometer output
181TCAS antena is
- Aomnidirectional blade type L-band
- Bphased-array L-band
- Cdirectional antena
182MLS frequency is
- A600-6100 MHz
- B5050-6050 MHz
- C5000-6000 MHz
183which colour on the weather radar screen does the pilot ovoid fly-through in order not to encounter strong thunderstrome and havy rain ?
- AMagenta
- BYellow
- CBlue
184GPWS is
- AW-band
- BX-band
- CL-band
185to minimize cross cable interference
- Aplace filter in power supply
- Brun radiating and affected cables as separate blundles
- Crun cables as single bundle
186wich 30 Hz signal from VOR ground station is frequency modulated
- Athe reference signal , wich is constant
- Bthe ident tone
- Cthe variable signal
187how is the gildeslope frequency chosen on the navigation control panel ?
- Ait is not manually chosen , It is paired with the VOR frequency
- BVia the G/S selector knob
- CIt is not manually chosen .IT is paired with the localizer frequency
188how many times does the INS ( Inertial navigation system ) integrate the acceleration signal it recives from the accelerometers to get the distance the aircraft has flow
- Atwice
- Bthree times
- Conce
189Radar altimeter uses what frequency
- A1200 MHz
- B2300 Mhz
- C4000 MHz
190Alert and deciosion heights differ in that
- Athe alert height is based on ILS equiptment and Decision height is based on RVR
- Bthe decision height is based on ILS equiptment and Alert height is based on RVR
- CThe alert height is based on Aircraft charecteristics and decision height is based on the airport facilities
191DME compares what measurement of slant distance ?
- Apulse transmission and return echo
- Bpulse pairs
- CAircraft range and height
192A TCAS blade aerial is
- Aa 1 -band omnidireccional array
- Bunidirecional
- Ca 1-band directional array
193FM improvements affect what system
- AVHF , VOR and ILS
- BADF , VOR and ILS
- CADF , VHF and ILS
194digital weather radar is on map mode . What happens ?
- ADisplay alerts
- Bswitches antennas
- CAntenna tilts down
195ACARs sends information from base to aircraft via
- Aprinter
- BFMS
- Cvoice
196what does 7700 indicate on an ATC control panel
- Ahijack
- BEmergency
- CRadio failure
197The number of VHF frequency channels is
- A360
- B720
- C760
198In an INS , vertical aceleration is calculated by
- Aaccelerometer and laser gyro
- Ban accelerometer
- Ca laser gyro
199the number of VHF frequency channels is
- A360
- B720
- C760
200In a VHF comms , with 8.33 kHz spacing , how many channels are used
- A720
- B350
- C2280
Information
- Description
- Test en sistemas 10, creado por oriol arrufat en 15/04/2020.
- Author
- oriol arrufat
- Language
- English
- Views
- 7
- Rating
- No ratings yet Rate this quiz
More on Airframe Structures and Design