Quiz
CCNA Basic Questions
Erstelle ein kostenloses Konto, um dieses Quiz zu beenden
Speichere deinen Fortschritt und sieh dir dein Endergebnis an.
oder mit deiner E-Mail registrieren
Schon ein Konto? Anmelden
Fragen in diesem Quiz (12)
1What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?
- AThe Layer 2 switch drops the received frame
- BThe Layer 2 switch floods packets to all ports except the receiving port in the given VLAN
- CThe Layer 2 switch sends a copy of a packet to CPU for destination MAC address learning
- DThe Layer 2 switch forwards the packet and adds the destination MAC address to Its MAC address table
2What is the destination MAC address of a broadcast frame?
- A00:00:0c:07:ac:01
- Bff:ff:ff:ff:ff:ff
- C43:2e:08:00:00:0c
- D00:00:0c:43:2e:08
- E00:00:0crfHfrff
3Which action is taken by a switch port enabled for PoE power classification override?
- AWhen a powered device begins drawing power from a PoE switch port a syslog message is generated
- BAs power usage on a PoE switch port is checked data flow to the connected device is temporarily paused
- CIf a switch determines that a device is using less than the minimum configured power it assumes the device has failed and disconnects
- DIf a monitored port exceeds the maximum administrative value for power, the port is shutdown and err-disabled
4In which way does a spine and-leaf architecture allow for scalability in a network when additional access ports are required?
- AA spine switch and a leaf switch can be added with redundant connections between them
- BA spine switch can be added with at least 40 GB uplinks
- CA leaf switch can be added with a single connection to a core spine switch
- DA leaf switch can be added with connections to every spine switch
5A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented? (Choose two)
- Arunts
- Bgiants
- Cframe
- DCRC
- Einput errors
6What are two reasons that cause late collisions to increment on an Ethernet interface? (Choose two)
- Awhen the sending device waits 15 seconds before sending the frame again
- Bwhen the cable length limits are exceeded
- Cwhen one side of the connection is configured for half-duplex
- Dwhen Carrier Sense Multiple Access/Collision Detection is used
- Ewhen a collision occurs after the 32nd byte of a frame has been transmitted
7What is the function of a server?
- AIt transmits packets between hosts in the same broadcast domain
- BIt provides shared applications to end users
- CIt routes traffic between Layer 3 devices
- DIt creates security zones between trusted and untrusted networks
8What is a function of TFTP in network operations?
- Atransfers a configuration files from a server to a router on a congested link
- Btransfers IOS images from a server to a router for firmware upgrades
- Ctransfers a backup configuration file from a server to a switch using a username and password
- Dtransfers files between file systems on a router
9What are two functions of a server on a network? (Choose two)
- Aruns applications that send and retrieve data for workstations that make requests
- Bachieves redundancy by exclusively using virtual server clustering
- Choused solely in a data center that is dedicated to a single client
- Druns the same operating system in order to communicate with other servers
- Ehandles requests from multiple workstations at the same time
10What is the primary function of a Layer 3 device?
- Ato analyze traffic and drop unauthorized traffic from the Internet
- Bto transmit wireless traffic between hosts
- Cforward traffic within the same broadcast domain
- Dto pass traffic between different networks
11What is the same for both copper and fiber interfaces when using SFP modules?
- AThey support an inline optical attenuator to enhance signal strength
- BThey accommodate single-mode and multi-mode in a single module
- CThey offer reliable bandwidth up to 100 Mbps in half duplex mode
- DThey provide minimal interruption to services by being hot-swappable
12Which two statements about the purpose of the OSI model are accurate? (Choose two)
- AA. Defines the network functions that occur at each layer
- BB. Facilitates an understanding of how information travels throughout a network
- CC. Changes in one layer do not impact other layer
- DD. Ensures reliable data delivery through its layered approach
Informationen
- Beschreibung
- CCNA Information Technology Quiz am CCNA Basic Questions, erstellt von Daniel Delano am 26/08/2021.
- Autor
- Daniel Delano
- Sprache
- English
- Aufrufe
- 4
- Schlagwörter
- Bewertung
- Noch keine Bewertungen Bewerte dieses Quiz