Quiz
CCNA Basic Questions
Create a free account to finish this quiz
Save your progress and see your final score.
Already have an account? Sign in
Questions in this quiz (12)
1What is the default behavior of a Layer 2 switch when a frame with an unknown destination MAC address is received?
- AThe Layer 2 switch drops the received frame
- BThe Layer 2 switch floods packets to all ports except the receiving port in the given VLAN
- CThe Layer 2 switch sends a copy of a packet to CPU for destination MAC address learning
- DThe Layer 2 switch forwards the packet and adds the destination MAC address to Its MAC address table
2What is the destination MAC address of a broadcast frame?
- A00:00:0c:07:ac:01
- Bff:ff:ff:ff:ff:ff
- C43:2e:08:00:00:0c
- D00:00:0c:43:2e:08
- E00:00:0crfHfrff
3Which action is taken by a switch port enabled for PoE power classification override?
- AWhen a powered device begins drawing power from a PoE switch port a syslog message is generated
- BAs power usage on a PoE switch port is checked data flow to the connected device is temporarily paused
- CIf a switch determines that a device is using less than the minimum configured power it assumes the device has failed and disconnects
- DIf a monitored port exceeds the maximum administrative value for power, the port is shutdown and err-disabled
4In which way does a spine and-leaf architecture allow for scalability in a network when additional access ports are required?
- AA spine switch and a leaf switch can be added with redundant connections between them
- BA spine switch can be added with at least 40 GB uplinks
- CA leaf switch can be added with a single connection to a core spine switch
- DA leaf switch can be added with connections to every spine switch
5A frame that enters a switch fails the Frame Check Sequence. Which two interface counters are incremented? (Choose two)
- Arunts
- Bgiants
- Cframe
- DCRC
- Einput errors
6What are two reasons that cause late collisions to increment on an Ethernet interface? (Choose two)
- Awhen the sending device waits 15 seconds before sending the frame again
- Bwhen the cable length limits are exceeded
- Cwhen one side of the connection is configured for half-duplex
- Dwhen Carrier Sense Multiple Access/Collision Detection is used
- Ewhen a collision occurs after the 32nd byte of a frame has been transmitted
7What is the function of a server?
- AIt transmits packets between hosts in the same broadcast domain
- BIt provides shared applications to end users
- CIt routes traffic between Layer 3 devices
- DIt creates security zones between trusted and untrusted networks
8What is a function of TFTP in network operations?
- Atransfers a configuration files from a server to a router on a congested link
- Btransfers IOS images from a server to a router for firmware upgrades
- Ctransfers a backup configuration file from a server to a switch using a username and password
- Dtransfers files between file systems on a router
9What are two functions of a server on a network? (Choose two)
- Aruns applications that send and retrieve data for workstations that make requests
- Bachieves redundancy by exclusively using virtual server clustering
- Choused solely in a data center that is dedicated to a single client
- Druns the same operating system in order to communicate with other servers
- Ehandles requests from multiple workstations at the same time
10What is the primary function of a Layer 3 device?
- Ato analyze traffic and drop unauthorized traffic from the Internet
- Bto transmit wireless traffic between hosts
- Cforward traffic within the same broadcast domain
- Dto pass traffic between different networks
11What is the same for both copper and fiber interfaces when using SFP modules?
- AThey support an inline optical attenuator to enhance signal strength
- BThey accommodate single-mode and multi-mode in a single module
- CThey offer reliable bandwidth up to 100 Mbps in half duplex mode
- DThey provide minimal interruption to services by being hot-swappable
12Which two statements about the purpose of the OSI model are accurate? (Choose two)
- AA. Defines the network functions that occur at each layer
- BB. Facilitates an understanding of how information travels throughout a network
- CC. Changes in one layer do not impact other layer
- DD. Ensures reliable data delivery through its layered approach
Information
- Description
- CCNA Information Technology Quiz on CCNA Basic Questions, created by Daniel Delano on 26/08/2021.
- Author
- Daniel Delano
- Language
- English
- Views
- 4
- Tags
- Rating
- No ratings yet Rate this quiz