Help shape GoConqr. What should we add next?

Quiz

Switch Questions

David Jimenez 10 questions

Take the quiz

Questions in this quiz (10)

  1. 1Refer to the exibit. Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data?Image for question 1
    1. ASwitch-1 will drop the data because it does not have an entry for that MAC address.
    2. BSwitch-1 will forward the data to its default gateway.
    3. CSwitch-1 will flood the data out all of its ports except the port from which the data originated.
    4. DSwitch-1 will send an ARP request out all its ports except the port from which the data originated.
  2. 2A technician has installed SwitchB and needs to configure it for remote access from the management workstation connected SwitchA. Which set of commands is required to accomplish this task?Image for question 2
    1. ASwitchB(config)#interface FastEthernet 0/1
      SwitchB(config)#ip address 192.168.8.252 255.255.255.0
      SwitchB(config)#no shutdown
    2. BSwitchB(config)#ip default-gateway 192.168.8.254
      SwitchB(config)#interface vlan 1
      SwitchB(config)#ip address 192.168.8.252 255.255.255.0
      SwitchB(config)#no shutdown
    3. CSwitchB(config)#interface vlan 1
      SwitchB(config)#ip address 192.168.8.252 255.255.255.0
      SwitchB(config)#ip default-gateway 192.168.8.254 255.255.255.0
      SwitchB(config)#no shutdown
    4. DSwitchB(config)#ip default-network 192.168.8.254
      SwitchB(config)#interface vlan 1
      SwitchB(config)#ip address 192.168.8.252 255.255.255.0
      SwitchB(config)#no shutdown
  3. 3A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?
    1. AMore collision domains will be created.
    2. BIP address utilization will be more efficient.
    3. CMore bandwidth will be required than was needed previously.
    4. DAn additional broadcast domain will be created.
  4. 4Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem? (Choose three)Image for question 4
    1. AEnsure that the Ethernet encapsulations match on the interconnected router and switch ports.
    2. BEnsure that cables A and B are straight-through cables.
    3. CEnsure cable A is plugged into a trunk port.
    4. DEnsure the switch has power.
    5. EReboot all of the devices.
    6. FReseat all cables.
  5. 5Refer to the exhibit. What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN? (Choose two)Image for question 5
    1. AThe number of collision domains would remain the same.
    2. BThe number of collision domains would decrease.
    3. CThe number of collision domains would increase.
    4. DThe number of broadcast domains would remain the same.
    5. EThe number of broadcast domains would decrease.
    6. FThe number of broadcast domains would increase.
  6. 6Refer to the exhibit. Give this output for SwitchC, what should the network administrator’s next action be?Image for question 6
    1. ACheck the trunk encapsulation mode for SwitchC’s fa0/1 port.
    2. BCheck the duplex mode for SwitchC’s fa0/1 port.
    3. CCheck the duplex mode for SwitchA’s fa0/2 port.
    4. DCheck the trunk encapsulation mode for SwitchA’s fa0/2 port.
  7. 7Which three statements accurately describe layer 2 Ethernet switches? (choose three)
    1. AMicrosegmentation decreases the number of collisions on the network.
    2. BIf a switch receives a frame for an unknown destination.it uses ARP to resolve the address.
    3. CSpanning Tree Protocol allows switches to automatically share vlan information.
    4. DIn a properly functioning network with redundant switched paths, each switched segment will contain one root bridge with all its ports in the forwarding state. All other switches in that broadcast domain will have only one root port.
    5. EEstablishing vlans increases the number of broadcast domains.
    6. FSwitches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
  8. 8Why will a switch never learn a broadcast address?
    1. ABroadcast frames are never sent to switches.
    2. BBroadcast addresses use an incorrect format for the switching table.
    3. CA broadcast address will never be the source address of a frame.
    4. DBroadcasts only use network layer addressing.
    5. EA broadcast frame is never forwarded by a switch.
  9. 9Refer to the exhibit. Which two statements are true of the interfaces on Switch1? (Choose two)Image for question 9
    1. AInterface FastEthernet0/2 has been disabled.
    2. BMultiple devices are connected directly to FastEthernet0/1.
    3. CFastEthernet0/1 is configured as a trunk link.
    4. DFastEthernet0/1 is connected to a host with multiple network interface cards
    5. EFastEthernet0/5 has statically assigned MAC addresses.
    6. FA hub is connected directly to FastEthernet0/5
  10. 10The network administrator normally establishes a Telnet session with the switch from host A. The administrator’s attempt to establish a connect via Telnet to the switch from host B fails, but pings from host B to other two hosts are successful. What is the issue for this problem?Image for question 10
    1. AHost B and the switch need to be in the same subnet.
    2. BThe switch needs an appropriate default gateway assigned.
    3. CThe switch interface connected to the router is down.
    4. DHost B need to be assigned an IP address in vlan 1.

Information

Description
Certificate CCNA (ICND1) Quiz on Switch Questions, created by David Jimenez on 14/04/2016.
Language
Español
Views
1
Tags
ccnaicnd1certificate
Rating
No ratings yet
Rate this quiz
Rate this quiz

Feedback

What is it about?

What should we add next?